fantastic furniture KELLY User manual

Assembly Instructions
BUNK
KELLY
Ver1.2

Page 2
2
3
56
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
W
A
R
N
N
G
WARNING
Check no parts are missing.
4
fully tighten screws（leave slightly
loose.When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.

Page 3
28x Bolts
(M6x15mm)
(H1)
5x Small Endcap
(H5)
(H2)
4x Sleeve Nut
(M6x15mm)
(H4)
2x Top End
Panel
(P1)
Top Post
(P2)
Lower Post
(P10)
Side Rail
(P15)
Side Rail
(P16)
Lower Post
(P14)
Ladder
(P17)
Lower Post
(P13)
2x Base End
Panel
(P12)
Lower Post
(P11)
Front Guard
(P6)
Back Guard
(P7)
Top Post
(P3)
2x Slats
(P8)
Top Post
(P4)
4x Mid Post
(P9)
Top Post
(P5)
4x Bolts
(M6x35mm)
(H3)
7x Bolts
(M6x65mm)
4x Top Endcap
plus 4x Extra Top Endcap
4x Foot Endcap
plus 4x Extra foot Endcap
(H6) (H7)
M4-Allen key
What you Need
To Assemble the Body
(Tools not provided)
Mallet
Please make sure you have all these parts before you start.

Step 1
Step 2
You will need:
8x Bolts
M6 x 15mm
(H1)
(H1)
(P2) (P5)
(P4)
(P1)
(P3)
(P1)
(H3)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
(H3)
(H1)
(H5)
(H1)
(H3)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
4x Top Endcap
(H6)
(H6)
(H6)
(H6)
(H6)
You will need:
8x Bolts
M6 x 15mm
(H1)
3x Bolts
M6 x 65mm
(H3)
(P6)
(P7)
M4-Allen key provided
Attach Top Post (P2 & P3) to Top End Panel (P1) using 4x Bolts (H1). Insert 2x Top Endcap (H6) into
Attach the Front Guard (P6) to the Top Posts with 4x Bolts (H1) and 1x Bolt (H3),
attach Back Guard (P7) with 4x Bolts (H1) and 2x Bolts (H3). Insert 1x Small
Endcap (H5) as shown.
each Top Post. Repeat same for the other top bed end assembly as shown.
M4-Allen key provided
Assemble the top bed
Page 4
1x Small Endcap
(H5)

Step 3
Step 4
You will need:
4x Bolts
M6 x 15mm
(H1)
4x Bolts
M6 x 65mm
(H3)
4x Foot Endcap
(H7)
(Tools not provided)
Mallet
（P8）
Attach the Slats (P8).
Some effort is required to pull each slat into
position as the centre strap is designed to keep the slats tight.
Insert Mid Posts (P9) into Lower Posts (P10 & P11), then attach these to
Base End Panel (P12) using 2x Bolts (H1) and 2x Bolts (H3). Insert 2x Foot Endcap (H7)
into each Lower Post. Repeat same for the other base end as shown.
Well done. You have assembled the top bed, and now we will assemble the bottom bed.
Assemble the bottom bed
M4-Allen key provided
(P9)
(P9)
(H3)
(H1)
(H7) (H7)
(H7)
(H7)
(P10)
(P11) (P13)
(P14)
(H1) (H1)
(H1)
(H3) (H3)
(H3)
(P12) (P12)
(P9)
(P9)
Page 5

Step 5
Step 6
You will need:
8x Bolts
M6 x 15mm
(H1)
M4-Allen key provided
(P15)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
(P16)
Attach the Side Rails (P15 & P16) to the end assembles using 8x Bolts (H1).
(Tools not provided)
Mallet
note:holes for ladder
Attach the Slats (P8). Some effort is required to pull each slat into position as the centre strap is
designed to keep the slats tight.
(P8)
Well done. You have assembled the bottom bed. The two beds will now be put together to form
the bunk bed.
note: In the future if you require two single beds, the bunk can be disassembled. Remember to
remove the mid posts from the bottom bed and insert the spare end caps.
Page 6

Step 7
Step 8
Two people carefully lift the top bed into position. Note location of holes for ladder.
You will need:
4x Bolts
4x Small Endcap
M6 x 35mm
(H2)
(H2)
(H5)
4x Sleeve Nut
M6 x 15mm
(H5)
(H4)
(H5)
(H4)
M4-Allen key provided
Fit 4x Endcap (H5) to the Ladder (P17),
then attach ladder to the bunk using
4x Bolts (H2) and 4x Sleeve Nuts (H4).
Page 7