fantastic furniture Niva Lowline 1500mm User manual

Version 1.0
Niva
Lowline 1500mm
fantasticfurniture.com.au
Required
Two People

fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
Page 2
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram
for you chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
!Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
!Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
!Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
!Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
!If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
!Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au Page 3

Parts list
Box 1: Top Panel (P1); Left Side Panel (P2); Right Side Panel (P3); 4 x Leg (P5); Lower Divider Panel (P9);
2 x Drawer Left Side (P11); 2 x Drawer Right Side (P12); 2 x Drawer Back (P13); 2 x Drawer Base (P14);
2 x Drawer Rail (P15); Drawer Front (P16); Drawer Front (P17); Big Middle Leg (P18);
Small Middle Leg (P19); Hardware Pack.
Box 2: 2 x Short Rail (P6); 2 x Long Rail (P7); Upper Divider Panel (P8); Shelf (P10); Back Panel (P20).
Top Panel (P1)
What you need
to assemble the product
Othe tools you need
Flat head screwdriver; Phillips head
screwdriver; Mallet
fantasticfurniture.com.au
Page 4
Shelf (P10)
Left Side
Panel (P2)
Right Side Panel
(P3)
Bottom Panel (P4)
Leg (P5)
Leg (P5)
Leg (P5)
(P5)
Short Rail
(P6)
Short Rail
(P6)
Long Rail (P7)
Long Rail (P7)
Upper Divider
Panel (P8)
Lower Divider
Panel (P9)
Drawer Left
Side (P11)
Drawer Right
Side (P12)
Drawer Back (P13)
Drawer Base (P14)
Drawer Rail (P15)
(P11)
Drawer Front (P16)
(P15)
(P14)
(P13)
Drawer Front (P17)
(P12)
Big Middle
Leg (P18)
Small Middle
Leg (P19)
Back Panel (P20)

fantasticfurniture.com.au
Page 5
Hardware Pack
57 x Cam Bolts
(H1)
45 x Big Cam
Nuts (H2)
44 x Dowels
(H3)
12 x Small Cam
Nuts (H4)
24 x Screws
(H6)
#6x12 mm
4 x Screws
(H9)
#10x38 mm
1 x Adjustable
Foot (H10)
19x Screws
(H5)
#10x38 mm
4 x Felt Feet
(H8)
4 x Slides
(H7)

Step 1
Page 6fantasticfurniture.com.au
You will need
13 x Cam bolts
(H1)
Screw 13 x cam bolts (H1) into bottom panel (P4) as shown,
tighten with a Phillips head screwdriver.
Step 2
Phillips head
screwdriver
You will need
14 x Dowels
(H3) Mallet
Insert 3 x dowels (H3) into each short rail (P6) as shown.
Insert 4 x dowels (H3) into each long rail (P7) as shown.
Use a mallet to gently tap the dowels into place if needed.
(P4)
H1
(P7)
(P6)
H1
H1
H1
H1
H1
(P6)
(P7)
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H1
H1
H1 H1
H1
H3
H3

Step 3
Page 7fantasticfurniture.com.au
You will need
8 x Cam bolts
(H1)
Screw 2 x cam bolts (H1) into each leg (P5) using a Phillips head screwdriver.
Attach 1 x felt foot (H8) onto each leg (P5) as shown.
Step 4
Phillips head
screwdriver
You will need
4 x Big cam
nuts (H2)
Fit each short rail (P6) between 2 x legs (P5).
Insert 2 x big cam nuts (H2) each into short rail (P6).
Using a flat head screwdriver, turn the big cam nuts (H2) clockwise to lock.
4 x Felt feet
(H8)
(P5)
H1
H1
H8
X4
Flat head
screwdriver
H2
(P5)
(P6) (P5)
(P5)
(P5)
(P6)
H2
H2
H2
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.

Step 5
Page 8fantasticfurniture.com.au
You will need
Position 2 x long rails (P7) between the assembled units as shown.
Insert 4 x big cam nuts (H2) into long rails (P7), using a flat head screwdriver
turn clockwise to lock.
Step 6
You will need
10 x Big cam
nuts (H2)
Position the leg assembly onto bottom panel (P4), making sure the cam bolts on
the bottom panel (P4) are inserted into the holes on the leg assembly.
Insert 10 x big cam nuts (H2) into short rails (P6) and long rails (P7),
using a flat head screwdriver turn clockwise to lock.
Carefully turn the unit over.
Flat head
screwdriver
Flat head
screwdriver
4 x Big cam
nuts (H2)
(P5)
(P7)
(P7)
H2
H2
H2
(P5)
(P5)
(P5)
(P7)
(P7)
(P4)
(P6)
(P6)
H2
H2
H2
H2 H2

Step 7
Page 9fantasticfurniture.com.au
You will need
Step 8
You will need
Insert 2 x dowels (H3) into small middle leg (P19) and big middle leg (P18).
Attach small middle leg (P19) to big middle leg (P18) with 1 x screw (H5),
tighten with a Phillips head screwdriver.
Position middle legs (P18) & (P19) to bottom panel (P4).
Insert 3 x big cam nuts (H2) into middle legs (P18) & (P19), and turn clockwise to lock
using a flat head screwdriver.
Screw 1 x adjustable foot (H10) into big middle leg (P18) as shown.
H3
H5
(P19) (P18)
(P19)
(P18)
H3
2 x Dowels
(H3)
Phillips head
screwdriver
1 x Screw
(H5)
1 x Adjustable
foot (H10)
3 x Big cam
nuts (H2)
Flat head
screwdriver
(P4)
(P18) (P19)
H10
#10x38 mm
H2
H2

Step 9
Page 10fantasticfurniture.com.au
You will need
Screw 6 x cam bolts (H1) into bottom panel (P4) as shown,
tighten with a Phillips head screwdriver.
Screw 4 x screws (H9) into bottom panel (P4), tighten with a Phillips head screwdriver.
Step 10
You will need
Phillips head
screwdriver
Phillips head
screwdriver
Screw 6 x cam bolts (H1) into top panel (P1), tighten with a Phillips head screwdriver.
6 x Cam bolts
(H1)
6 x Cam bolts
(H1)
4 x Screws
(H9)
H1
H9
(P1)
H1
H1
H1
H1
H1
H1
H9
H9
H9
(P4)
#10x38 mm
H1
H1
H1
H1
H1