fantastic furniture STOCKHOLM BOOKCASE LARGE NARROW User manual

Version 1.0
STOCKHOLM
BOOKCASE LARGE NARROW
fantasticfurniture.com.au

fantasticfurniture.com.au PAGE 2
Looks like you’ve found
your Fantastic!
Love it? Share it!
Fantastic buy! Share how it looks at home for your
chance to win a $250 Fantastic Furniture Gift Card!
fantasticfurniture
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 10kgs/shelf.

PAGE 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Left Side Panel (P2);
Right Side Panel (P3);
Bottom Panel (P4);
Inner Top Panel (P5);
3 x Shelf Panels (P6);
2 x Inner Side Panels (P7);
Rail(P8);
3 x Back Panels (P9);
Shelf Panel (P10);
Back Panel (P11);
Door (P12);
4 x Legs (P13);
Drawer Front (P14);
Left Drawer Side (P15);
Right Drawer Side (P16);
Drawer Base (P17);
Drawer Back (P18);
Hardware pack
Left Drawer
Side (P15)
Right Drawer
Side (P16)
Drawer Back
(P18)
Drawer
Base
(P17)
Drawer Front
(P14)
Top Panel
(P1)
Right
Side
Panel
(P3)
Bottom Panel
(P4)
Back
Panel
(P9)
Door
(P12)
Inner
Top Panel
(P5)
Left
Side
Panel
(P2)
Shelf
Panel
(P6)
Shelf
Panel
(P6)
Shelf
Panel
(P6)
Inner
Side
Panel
(P7)
Inner
Side
Panel
(P7)
Back
Panel
(P9)
Back
Panel
(P9)
Back
Panel
(P11)
Shelf
Panel
(P10)
Rail
(P8)
4 x Legs
(P13)
26 x Cam
Bolts
(H3)
26x Cam
Nuts
(H4)
2 x Pin
Screws
(H12)
30 x Dowels
(H1)
18 x Small
Screws
(H5)
1 x CL
Runner
Track
(H6)
1 x CR
Runner
Track
(H7)
1 x DR
Runner
(H9)
1 x DL
Runner
(H8)
8 x Long
Screws
(H2)
2 x Hinges
(H11)
16 x Bolts
(H15)
1 x Allen
Key
(H16)
20 x Screws
(H17)
1 x Safety
Strap Screw
(H21)
1 x Safety
Strap
(H20)
2 x Washers
(H22)
4 x Wedges
(H18)
4 x Wedge
Screws
(H19)
2 x Magnetic
Catches
(H13)
12 x Small
Screws
(H10)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
PAGE 4
fantasticfurniture.com.au
DO NOT USE
4 x Leg Plates
(H23)
8 x Long
Bolts
(H14)

(P3)
(P3)
(P2)
(P2)
(P7)
(P7)
1 x CL Runner
Track (H6)
You will need
Step 1
6 x Small
Screws (H5)
Phillips Head
Screwdriver
1 x CR Runner
Track (H7)
H6
CL
H5
H7
CR
H5
H17
H17
H7
H5
H5
Step 2
You will need
Phillips Head
Screwdriver
H3
H3 H1
22 x Cam Bolts
(H3)
Attach 2 x Inner Side Panels (P7)
to Left Side Panel (P2) and Right
Side Panel (P3) with 16 x Screws
(H17) by tightening with the Phillips
Head Screwdriver. Attach 1 x CL Runner
Track (H6) to Left Side Panel (P2) and 1 x CR Runner Track (H7) to Right Side Panel (P3) with
6 x Small Screws (H5) by tightening with the Phillips Head Screwdriver.
Secure 22 x Cam Bolts (H3) to Left and
Right Side Panels (P2&P3) by tightening
with the Phillips Head Screwdriver. Insert 11 x
Dowels (H1) into Left Side Panel (P2) as shown.
16 x Screws
(H17)
11 x Dowels
(H1)
H6
fantasticfurniture.com.au PAGE 5

You will need
Step 3
8 x Small
Screws (H5)
Insert 11 x Cam Nuts (H4) into Inner Top Panel (P5),
3 x Shelf Panels (P6), Shelf Panel (P10) and Rail (P8)
and attach to Left Side Panel (P2) by tightening each
Cam Nut with the Phillips Head Screwdriver.
Note: Before securing panels - ensure all Cam Nuts are on the bottom of
each shelf panel except for the Inner Top Panel which should face upwards.
Phillips Head
Screwdriver
2 x Magnetic
Catches (H13)
Step 4
You will need
11 x Cam Nuts
(H4)
Attach 2 x Magnetic Catches (H13) to each side of Rail (P8) with 8 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
Phillips Head
Screwdriver
FLIP
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
(P8)
H5
H13
(P2)
(P6)
(P6)
(P8)
(P5)
H4 (P6)
fantasticfurniture.com.au
fantasticfurniture.com.au PAGE 6
(P8)
H5
H13
(P10)
H5
H13
Please note the position
of the head of the Catch
before fixing.
Ensure the Top Panel (P5), Shelf Panels (P6x3)
& Shelf Panel (P10) are aligned so that the
grooves are all at the back as shown.
PVC
PVC

Step 5
Slide 3 x Back Panels (P9) into the grooves of Inner Top & Shelf Panels (P5&P6x3).
Insert 11 x Dowels (H1) and 11 x Cam Nuts (H4) into Inner Top Panel (P5), 3 x Shelf
Panels (P6), Shelf Panel (P10) and Rail (P8) and attach to Right Side Panel (P3) by
tightening each Cam Nut with the Phillips Head Screwdriver.
(P6) (P6)
(P5)
(P9)
(P9)
(P9)
Ensure laminated
side of panel is
facing inwards.
You will need
Phillips Head
Screwdriver
11 x Dowels
(H1)
Step 6
11 x Cam Nuts
(H4)
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
(P6)
H4
H1
(P6)
(P6)
(P5)
(P6)
(P3)
(P8)
fantasticfurniture.com.au PAGE 7
H4
Required
Two People
(P10)

You will need
Phillips Head
Screwdriver
Step 7
Insert 4 x Dowels (H1) into the top of Left & Right Side Panels (P2&P3) and secure
Top Panel (P1) to the top of the unit with 4 x Long Screws (H2) by tightening with the
Phillips Head Screwdriver. Slide Back Panel (P11) into the grooves of Left and Right
Side Panels (P2&P3) at the bottom of the unit.
Insert 4 x Dowels (H1) into the bottom of Left & Right Side Panels (P2&P3) and
secure Bottom Panel (P4) to the bottom of the unit with 4 x Long Screws (H2) by
tightening with the Phillips Head Screwdriver.
4 x Dowels
(H1)
4 x Long
Screws (H2)
(P1)
(P2)
(P3)
H2
H1
(P11)
Ensure laminated
side of panel is
facing inwards.
H2
H1
(P2)
(P3)
(P4)
You will need
Phillips Head
Screwdriver
Step 8
4 x Dowels
(H1)
4 x Long
Screws (H2)
fantasticfurniture.com.au PAGE 8

(P14)
You will need
Step 10
Step 9
You will need
H15
H16
Attach 4 x Cam Bolts (H3) and 1 x Pin Screw (H12) to Drawer Front (P14) by
tightening with the Phillips Head Screwdriver.
H3
16 x Bolts
(H15)
1 x Allen Key
(H16)
1 x Pin
Screw (H12)
H12
Secure 4 x Leg Plates (H23) to 4 x Legs (P13) with 8 x Long Bolts (H14) by tightening with
the Allen Key (H16). Attach 4 x Legs (P13) to Bottom Panel (P4) with 16 x Bolts (H15) by
tightening with the Allen Key (H16).
(P2)
(P3)
(P4) H15
(P13)
4 x Cam Bolts
(H3)
Phillips Head
Screwdriver
fantasticfurniture.com.au PAGE 9
(P13)
H23
H14
H16
Phillips Head
Screwdriver
4 x Leg Plates
(H23)
8 x Long
Bolts (H14)
Ensure the countersunk holes on the
Leg Plate are face up, so that the
Screws sit flush with the top of the
Leg Plate once attached.

(P18)
(P17)
(P14)
(P15)
(P16)
(P15)
(P16)
You will need
Step 11
Step 12
H4
H4
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Insert 4 x Cam Nuts (H4) into Left & Right Drawer Sides (P15&P16) and attach to
Drawer Front (P14) by tightening Cam Nuts with the Phillips Head Screwdriver.
Attach Drawer Back (P18) to Left & Right Drawer
Sides (P15&P16) with 4 x Screws (H17) by tightening
with the Phillips Head Screwdriver. Before securing - Ensure the Bottom
Panel lines up with the grooves the whole way around the drawer.
H17
Ensure laminated
side of panel is
facing inwards.
4 x Cam Nuts
(H4)
Phillips Head
Screwdriver
Slide the Drawer Base (P17) into the grooves of Left & Right Drawer Sides (P15&P16) as shown.
Phillips Head
Screwdriver
You will need
Step 13
4 x Screws
(H17)
(P15)
(P16)
fantasticfurniture.com.au PAGE 10