fantastic furniture Pod Desk User manual

Version 1.0
Pod
fantasticfurniture.com.au
Desk 1 Drawer

fantasticfurniture.com.au Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 10Kg/Drawer.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Hardware Pack
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
DO NOT USE
Page 4
fantasticfurniture.com.au
Top Panel
(P1)
Bottom Panel
(P2)
x4
Right Side
Panel
(P4)
Rail
(P6)
Leg
(P7)
Back Panel
(P5)
Left Side
Panel
(P3)
Left
Drawer Side
(P9)
Right
Drawer Side
(P10)
Drawer Back
(P12) Drawer
Base
(P11)
Support
Rail
(P13)
Drawer Front
(P8)
Parts list
Top Panel (P1);
Bottom Panel (P2):
Left Side Panel (P3);
Right Side Panel (P4);
Back Panel (P5);
Rail (P6);
4 x Legs (P7);
Drawer Front (P8);
Left Drawer Side (P9);
Right Drawer Side (P10);
Drawer Base (P11);
Drawer Back (P12);
Support Rail (P13)
9 x Cam
Bolts
(H3)
9 x Cam
Nuts
(H4)
12 x Dowels
(H1)
10 x Small
Screws
(H5)
1 x CL Runner
Track
(H6)
1 x CR Runner
Track
(H7)
1 x DR Runner
(H9)
1 x Handle
(H10)
1 x DL Runner
(H8)
15 x Long
Screws
(H2)
16 x Short
Bolts
(H12)
3 x Long
Bolts
(H13)
1 x Allen Key
(H14)
1 x Handle
Screw
(H11)
1 x Washer
(H15)

You will need
Step 1
You will need
Step 2
Page 5
fantasticfurniture.com.au
Attach 4 x Cam Bolts (H3) to Top Panel (P1) by tightening with the Phillips Head Screwdriver.
Attach Rail (P6) to Top Panel (P1) with 3 x Long Bolts (H13) by tightening with the Allen Key (H16).
Attach 1 x CL Runner Track (H6) and 1 x CR Runner Track (H7) to Left & Right Side
Panels (P3 & P4) with 6 x Small Screws (H5) by tightening with the Phillips Head
Screwdriver.
4 x Cam Bolts
(H3)
Phillips head
screwdriver
H5
H5
H5
H5
H5
H5
H6
H7
Phillips Head
Screwdriver
1 x CL Runner
Tracks (H6)
1 x CR Runner
Tracks (H7)
6 x Small
Screws (H5)
1 x Allen Key
(H16)
3 x Long
Bolts (H13)
H7
CR
H5
H6
CL
H5
H3
H13
H13
H13
H3
H3
H3
(P1)
(P6)
(P1)
(P3)
(P4)
H13
(P6)
H16

You will need
Step 3
You will need
Step 4
Page 6
fantasticfurniture.com.au
Insert 4 x Dowels (H1) into Top Panel (P1). Insert 4 x Cam Nuts (H4) into Left & Right Side
Panels (P3 & P4) as shown. Rotate the cam nuts so the arrows point towards the incoming
cam bolts. Attach Left & Right Side Panels (P3 & P4) to Top Panel (P1) by tightening
all cam nuts with the Phillips Head Screwdriver.
Phillips Head
Screwdriver
H2
H1
H1
H2
H1
H2
H2
H1
H1
H1
H1
H4
H4
H4
4 x Cam Nuts
(H4)
4 x Dowels
(H1)
Phillips Head
Screwdriver
4 x Dowels
(H1)
4 x Long
Screws (H2)
Insert 4 x Dowels (H1) into Left & Right Side Panels (P3 & P4).
Attach Bottom Panel (P2) to Left & Right Side Panels (P3 & P4) with 4 x Long Screws
(H2) by tightening with the Phillips Head Screwdriver.
(P1)
(P3)
(P4)
(P2)
(P3)
(P4)
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
H2

You will need
Step 6
You will need
Step 5
Page 7
fantasticfurniture.com.au
Phillips head
screwdriver
Attach 4 x legs (P7) to Bottom Panel (P2) with 16 x Short Bolts (H12) by tightening
with the Allen Key (H14).
H12
H12
H12
H12
H12
H14
H12
16 x Short
Bolts (H12)
1 x Allen Key
(H14)
5 x Cam Bolts
(H3)
Attach 5 x Cam Bolts (H3) to Drawer Front Panel (P8) by tightening with the Phillips Head
Screwdriver.
(P8)
(P2)
(P7)
(P7)
(P7)
(P7)
H3
H3
H3

Step 7
You will need
Page 8
fantasticfurniture.com.au
Phillips Head
Screwdriver
Step 8
Attach Drawer Back (P12) and Support Rail (P13) to Left & Right Drawer Side (P9 & P10) with
5 x Long Screws (H2) by tightening with the Phillips Head Screwdriver.
Slide the Drawer Base (P11) into the grooves of Left & Right Drawer Sides (P9 & P10)
and Drawer Back (P12) as shown.
5 x Long
Screws (H2)
H2
H2
H2
H2
H2
(P9)
(P9)
(P11)
(P13)
(P12)
(P12)
(P10)
(P10)

You will need
Step 10
Page 9
fantasticfurniture.com.au
Phillips head
screwdriver
You will need
Step 9
Insert 5 x Cam Nuts (H4) into Left & Right Drawer Side (P9 & P10) and Support Rail (P13)
as shown. Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Drawer Front (P8) to Left & Right Drawer Side (P9 & P10) and Support Rail (P13)
by tightening all cam nuts with the Phillips Head Screwdriver.
Ensure that the Drawer Base (P11) is slotted into the grooves of Drawer Front (P8).
Phillips head
screwdriver
H4H4
H4
H4
H4
5 x Cam Nuts
(H4)
(P9)
(P9)
(P8)
(P11)
(P13)
(P10)
(P10)
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
Attach 1 x DL Runner (H8) to the bottom of Left Drawer Side (P9) and 1 x DR Runner (H9)
to the bottom of Right Drawer Side (P10) with 4 x Small Screws (H5) by tightening with the
Phillips Head Screwdriver.
H5
H5
H5
H8
H9
H5
4 x Small
Screws (H5)
1 x DR
Runner (H9)
1 x DL
Runner (H8)

Page 10
fantasticfurniture.com.au
Phillips head
screwdriver
You will need
Step 11
Attach 1 x Handle (H10) to Drawer Front (P8) with 1 x Handle Screw (H11) by tightening
with the Phillips Head Screwdriver.
1 x Handle
(H10)
1 x Handle
Screw (H11)
Step 12
Insert the assembled drawer into the corresponding compartment as shown.
Ensure the drawer slide easily along the rails.
(P8)
H10
H11