fantastic furniture STOCKHOLM User manual

Version 1.0
STOCKHOLM
BOOKCASE LARGE WIDE
fantasticfurniture.com.au

fantasticfurniture.com.au PAGE 2
Looks like you’ve found
your Fantastic!
Love it? Share it!
Fantastic buy! Share how it looks at home for your
chance to win a $250 Fantastic Furniture Gift Card!
fantasticfurniture
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable
surface. Connecting attachments for your wall are not included
since dierent surface materials require dierent attachments.
Please seek professional advice if you are in doubt of what wall
connections to use.
Recommended weight capacity : 10kgs/shelf.

PAGE 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
!Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
!Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
!Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
!Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
!If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
!Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Left Drawer
Side (P18)
Right Drawer
Side (P19)
Drawer Back
(P22)
Drawer
Base
(P21)
Drawer Front
(P17)
Top Panel
(P1) Right
Side
Panel
(P4)
Bottom
Panel
(P2)
Door
(P15)
Back
Panel
(P10)
Back
Panel
(P11)
Back
Panel
(P11)
Shelf Panel
(P8)
Inner Top Panel
(P7)
Inner
Side
Panel
(P5)
Door
(P15)
4 x Legs
(P6)
Left
Side
Panel
(P3)
Inner
Side
Panel
(P5)
Shelf
Panel
(P16)
Back
Panel
(P9) Shelf Panel
(P8)
x 2
Back
Panel
(P9)
4 x Pin
Screws
(H12)
Rail
(P20)
Rail
(P14)
Rail
(P12)
Rail
(P13)
Parts list
Top Panel (P1);
Bottom Panel (P2);
Left Side Panel (P3);
Right Side Panel (P4);
2 x Inner Side Panels (P5);
4 x Legs (P6);
Inner Top Panel (P7);
2 x Shelf Panels (P8);
2 x Back Panels (P9);
Back Panel (P10);
2 x Back Panels (P11);
Rail(P12);Rail(P13);Rail (P14);
2 x Doors (P15);
Shelf Panel (P16);
2 x Drawer Fronts (P17);
2 x Left Drawer Sides (P18);
2 x Right Drawer Sides (P19);
2 x Rails (P20);
2 x Drawer Bases (P21);
2 x Drawer Backs (P22);
Hardware pack
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
PAGE 4
DO NOT USE
fantasticfurniture.com.au
4 x Leg
Plates
(H22)
8 x Long
Bolts
(H23)
34 x Cam
Bolts
(H3)
34x Cam
Nuts
(H4)
28 x Dowels
(H1)
36 x Small
Screws
(H5)
2 x CL
Runner
Tracks
(H6)
2 x CR
Runner
Tracks
(H7)
2 x DR
Runners
(H9)
2 x DL
Runners
(H8)
8 x Long
Screws
(H2)
4 x Hinges
(H11)
16 x Bolts
(H14)
1 x Allen
Key
(H15)
22 x Screws
(H16)
1 x Safety
Strap Screw
(H20)
1 x Safety
Strap
(H19)
2 x Washers
(H21)
8 x Wedges
(H17)
8 x Wedge
Screws
(H18)
4 x Catches
(H13)
24 x Small
Screws
(H10)

(P4)
(P4)
(P3)
(P3)
(P5)
(P5)
2 x CL Runner
Tracks (H6)
You will need
Step 1
12 x Small
Screws (H5)
Phillips Head
Screwdriver
2 x CR Runner
Tracks (H7)
H6
CL
H5
H7
CR
H5
H16
H16
H5
H5
H6
H6
H7
H7
H5
H5
Step 2
You will need
Phillips Head
Screwdriver
H3
H3 H1
24 x Cam Bolts
(H3)
Attach 2 x Inner Side Panels (P5)
to Left Side Panel (P3) and Right
Side Panel (P4) with 12 x Screws
(H16) by tightening with the Phillips
Head Screwdriver. Attach 2 x CL Runner
Tracks (H6) to Left Side Panel (P3) and 2 x CR Runner Tracks (H7) to Right Side Panel (P4) with
12 x Small Screws (H5) by tightening with the Phillips Head Screwdriver.
Secure 24 x Cam Bolts (H3) to Left and
Right Side Panels (P3&P4) by tightening
with the Phillips Head Screwdriver. Insert 10 x
Dowels (H1) into Left Side Panel (P3) as shown.
12 x Screws
(H16)
10 x Dowels
(H1)
fantasticfurniture.com.au PAGE 5

(P3)
You will need
Step 4
You will need
Step 3
12 x Cam Nuts
(H4)
Phillips Head
Screwdriver
16 x Small
Screws (H5)
4 x Catches
(H13)
Insert 12 x Cam Nuts (H4) into Inner Top Panel (P7),
2 x Shelf Panels (P8), Shelf Panel (P16) and Rails
(P12&P13&P14) as shown and attach to Left Side Panel (P3)
by tightening each Cam Nut with the Phillips Head Screwdriver.
Note: Before securing panels - ensure all Cam Nuts are on the bottom of
each shelf panel except for the Inner Top Panel which should face upwards.
Attach 4 x Catches (H13) to each side of Rail (P14) and Rail (P13) with 16 x Small Screws (H5)
by tightening with the Phillips Head Screwdriver.
Phillips Head
Screwdriver
(P14)
(P14)
(P13)
FLIP
H5
H5
H5
H5
H13
H13
H13
H13
(P8)
(P8)
(P13)
(P14)
(P12)
(P16)
(P7)
H4
H4
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
fantasticfurniture.com.au
fantasticfurniture.com.au PAGE 6

(P8)
(P8)
(P16)
(P7)
(P9)
(P9)
(P10)
(P11)
(P12)
You will need
Step 6
Phillips Head
Screwdriver
10 x Dowels
(H1)
Step 5
12 x Cam Nuts
(H4)
Ensure laminated
side of panel is
facing inwards.
Insert 10 x Dowels (H1) and 12 x Cam Nuts (H4) into Inner
Top Panel (P7), 2 x Shelf Panels (P8), Shelf Panel (P16) and
Rails (P12&P13&P14) and attach to Right Side Panel (P4) by
tightening each Cam Nut with the Phillips Head Screwdriver.
Slide 2 x Back Panels (P9) and Back Panels (P10&P11)
into the grooves of Inner Top & Shelf Panels (P7&P8x2) and
Rail & Shelf Panel (P12&P16).
H4
H1
(P8)
(P8)
(P16)
(P7)
(P12)
(P13) (P14)
(P4)
H4
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Required
Two People
fantasticfurniture.com.au PAGE 7

(P1)
(P3)
(P4)
H2
H1
(P3)
(P11)
(P4)
Ensure laminated
side of panel is
facing inwards.
Step 8
You will need
Step 7
Phillips Head
Screwdriver
4 x Long
Screws (H2)
Insert 4 x Dowels (H1) into the top of Left & Right Side Panels (P3&P4) and secure
Top Panel (P1) to the top of the unit with 4 x Long Screws (H2) by tightening with the
Phillips Head Screwdriver.
Slide Back Panel (P11) into the grooves of Left and Right
Side Panels (P3&P4) at the bottom of the unit.
4 x Dowels
(H1)
fantasticfurniture.com.au PAGE 8

Secure 4 x Leg Plates (H22) to 4 x Legs (P17) with 8 x Long Bolts (H23) by tightening with
the Allen Key (H15). Attach 4 x Legs (P17) to Bottom Panel (P2) with 16 x Bolts (H14) by
tightening with the Allen Key (H15).
Insert 4 x Dowels (H1) into the bottom of Left & Right Side Panels (P3&P4) and
secure Bottom Panel (P2) to the bottom of the unit with 4 x Long Screws (H2) by
tightening with the Phillips Head Screwdriver.
You will need
Step 9
Phillips Head
Screwdriver
4 x Long
Screws (H2)
4 x Dowels
(H1)
You will need
Step 10
H2
H1
(P3)
(P4)
(P2)
(P3)
(P4)
(P2)
Phillips Head
Screwdriver
4 xLeg Plates
(H22)
8 x Long
Bolts (H23)
16 x Bolts
(H14)
1 x Allen Key
(H15)
H14
(P17)
H15
(P17)
H14
fantasticfurniture.com.au PAGE 9
(P17)
H22
H23
H15

(P15)
(P15)
(P15)
You will need
Step 12
H10 H10
H11 H11
Attach the Doors (P15x2) to the unit by securing 2 x Hinges (H11) to Left & Right
Side Panels (P3&P4) with 16 x Small Screws (H10) by tightening with the Phillips
Head Screwdriver.
Attach 4 x Hinges (H11) and 2 x Pin Screws (H12) to both Doors (P15x2) with 8 x Small
Screws (H10) by tightening with the Phillips Head Screwdriver.
Step 11
Phillips Head
Screwdriver
You will need
Phillips Head
Screwdriver
8 x Small
Screws (H10)
16 x Small
Screws (H10)
H11
H10
x 2
(P3)
(P4)
H11
H10
H13
H11
H10
To open the door, firmly press the
middle or top left of the door front
to trigger the Catch to bounce the
door open.
If the door does not pop open when
pressed or is not sitting flush with
the front of the unit, reach under the
Rail and adjust the Catch by gently
turning left or right to reach the right
resistance.
4 x Hinges
(H11)
fantasticfurniture.com.au PAGE 10
2 x Pin Screws
(H12)
H12