fantastic furniture Pod Bedside User manual

Version 1.0
Pod
Bedside 1 Drawer
fantasticfurniture.com.au

fantasticfurniture.com.au Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 10Kg/Drawer.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
!Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
!Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
!Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used as they may not fit through a door once assembled.
!Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
!If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
!Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Bottom Panel (P2)
Left Side Panel (P3);
Right Side Panel (P4);
Back Panel (P5);
Shelf Panel (P6);
Drawer Front (P8);
Left Drawer Side (P9);
Right Drawer Side (P10);
Drawer Base (P11);
Drawer Back (P12);
Hardware pack
Left Drawer
Side (P9)
Right Drawer
Side (P10)
Drawer Back
(P12)
Drawer
Base (P11)
Drawer
Front (P8)
Top Panel
(P1)
Right Side
Panel (P4)
Left Side
Panel
(P3)
Bottom
Panel
(P2)
Back Panel
(P5)
Shelf Panel
(P6)
Leg
(P7) x4
1 x Washer
(H19)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
12 x Cam
Bolts
(H3)
12 x Cam
Nuts
(H4)
12 x Dowels
(H1)
10 x Small
Screws
(H5)
1 x CL Runner
Track
(H6)
1 x CR Runner
Track
(H7)
1 x DR Runner
(H9)
1 x Handle
(H10)
1 x DL Runner
(H8)
8 x Long
Screws
(H2)
4 x Leg
Plates
(H12)
8 x Long
Bolts
(H13)
16 x Short
Bolts
(H14)
4 x Wedges
(H15)
4 x Wedge
Screws
(H16)
1 x Allen Key
(H17)
4 x Plastic
Glides
(H18)
1 x Handle
Screw
(H11)

6 x Small
Screws (H5)
(P3)
(P4)
(P1)
You will need
Step 1
H7
CR
H5
Step 2
You will need
Phillips Head
Screwdriver
4 x Cam Bolts
(H3)
Attach 4 x Cam Bolts (H3) to Top Panel (P1) by tightening with the Phillips Head Screwdriver.
Attach 1 x CL Runner Track (H6) and 1 x CR Runner Track (H7) to Left & Right
Side Panels (P3 & P4) with 6 x Small Screws (H5) by tightening with the Phillips
Head Screwdriver.
fantasticfurniture.com.au Page 5
1 x CL Runner
Track (H6)
H6
CL
H5
H7
1 x CR Runner
Track (H7)
Phillips Head
Screwdriver
H3
H3
H3
H3
H6
H5
H5

You will need
Step 3
Step 4
You will need
Attach 4 x Cam Bolts (H3) to Left & Right Side Panels (P3 & P4) by tightening with the Phillips
Head Screwdriver.
Insert 4 x Cam Nuts (H4) and 4 x Dowels (H1) into Shelf Panel (P6) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Left & Right Side Panels (P3 & P4) to Shelf Panel (P6) by tightening all cam
nuts with the Phillips Head Screwdriver.
Phillips Head
Screwdriver
4 x Cam Nuts
(H4)
Phillips Head
Screwdriver
4 x Dowels
(H1)
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
Ensure that (P6) is
facing the right way.
The front of (P6) will
be flush with front of
(P3) and (P4).
(P3)
(P3)
(P4)
(P4)
fantasticfurniture.com.au
fantasticfurniture.com.au Page 6
4 x Cam Bolts
(H3)
H3
H3
H3
H3
(P6)
H1
H1
H1
H1
H4
H4
H4
H4

Slide Back Panel (P5) into the grooves of Left & Right Side Panel (P3 & P4) and
Top panel (P1).
Step 6
Step 5
You will need
4 x Cam Nuts
(H4)
Phillips Head
Screwdriver
4 x Dowels
(H1)
Insert 4 x Dowels (H1) into Top Panel (P1). Insert 4 x Cam Nuts (H4) into Left & Right Side
Panels (P3 & P4) as shown. Rotate the cam nuts so the arrows point towards the incoming
cam bolts. Attach Top Panel (P1) to Left & Right Side Panels (P3 & P4) by tightening all cam
nuts with the Phillips Head Screwdriver.
(P3)
(P3)
(P5)
(P1)
(P4)
(P4)
(P1)
fantasticfurniture.com.au Page 7
H1
H4
H4
H1
H1

You will need
Phillips Head
Screwdriver
Step 7
4 x Dowels
(H1)
Insert 4 x Dowels (H1) into Left & Right Side
Panels (P3 & P4).
Attach Bottom Panel (P2) to Left & Right Side
Panels (P3 & P4) with 4 x Long Screws (H2) by
tightening with the Phillips Head Screwdriver.
Ensure that the Back Panel (P5) is slotted into
the grooves of Bottom Panel (P2).
(P2)
(P3)
(P4)
fantasticfurniture.com.au Page 8
4 x Long
Screws (H2)
H1
H2
H2
H1
H2
H2
You will need
Step 8
Phillips Head
Screwdriver
Ensure the countersunk
holes on the Leg Plate are
facing up, so that the Screws
sit flush with the top of
the Leg Plate once attached.
(P7)
H12
H14
H13
4 x Leg
Plates (H12)
8 x Long Bolts
(H13)
16 x Short
Bolts (H14)
1 x Allen Key
(H17)
H17
H17
4 x Plastic
Glides (H18)
Hammer
H18
H2
H1
H18
H18
H18
H18
(P7)
(P7)
(P7)
(P7)
H14
H14
H14
H14
Secure 4 x Leg Plates (H12) to 4 x Legs (P7) with 8 x Long Bolts (H13)
by tightening with an Allen Key (H17).
Attach 4 x Legs (P7) to Bottom Panel (P2) with 16 x Short Bolts (H14)
by tightening with an Allen Key (H17).
Hammer 4 x Plastic Glides (H18) onto the bottom of Legs (P7).

Attach 4 x Cam Bolts (H3) to Drawer Front Panel (P8) by tightening with the Phillips Head
Screwdriver.
Slide the Drawer Bases (P11) into the grooves of Left & Right Drawer
Sides (P9 & P10) and Drawer Back (P12) as shown.
You will need
Step 10
Step 11
You will need
Step 9
(P8)
fantasticfurniture.com.au Page 9
Phillips Head
Screwdriver
Phillips Head
Screwdriver
4 x Long
Screws (H2)
H3 H3
4 x Cam Bolts
(H3)
H3 H3
Attach Drawer Back (P12) to Left & Right Drawer Side (P9 & P10) with 4 x Long Screws (H2) by
tightening with the Phillips Head Screwdriver.
(P9)
(P10)
(P12)
(P12)
H2
H2
H2
H2
(P9)
(P10)
(P11)

You will need
Step 12
Attach 1 x DL Runner (H8) to the bottom of Left Drawer Side (P9) and 1 x DR Runner (H9)
to the bottom of Right Drawer Side (P10) with 4 x Small Screws (H5) by tightening with
the Phillips Head Screwdriver.
4 x Cam Nuts
(H4)
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
(P9)
(P10)
Phillips Head
Screwdriver
fantasticfurniture.com.au Page 10
You will need
Step 13
4 x Small
Screws (H5)
Phillips Head
Screwdriver
1 x DR
Runner (H9)
1 x DL
Runner (H8)
H5
H5
H5
H8
H9
H5
Insert 4 x Cam Nuts (H4) into Left & Right Drawer
Side (P9 & P10) as shown.
Rotate the cam nuts so the arrows point towards the incoming
cam bolts.
Attach Drawer Front (P8) to Left & Right Drawer Side (P9 & P10) by tightening all cam nuts
with the Phillips Head Screwdriver.
Ensure that the Drawer Base (P11) is slotted into the grooves of Drawer Front (P8).
(P8)
(P11)
(P9)
(P10)
H4
H4
H4H4