fantastic furniture HAVANA Bookcase User manual

Version 1.0
HAVANA
Bookcase
www.fantasticfurniture.com.au
REQUIRED
TWO PEOPLE

www.fantasticfurniture.com.au PAGE 2
Enjoy
Your purchase from
Australia’s Best Value Furniture Store
Recommended weight capacity : 10KG/Shelf.
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied with a
wall strap to prevent toppling. We strongly recommend that this product is
permanently fixed to the wall or other suitable surface. Connecting
attachments for your wall are not included since different surface materials
require different attachments. Please seek professional advice if you are in
doubt of what wall connections to use.

Assembly checklist
Useful Information
www.fantasticfurniture.com.au PAGE 3
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Please see page 2 for any safety requirements or weight restrictions.

Top Panel (P1)
34 x Cam Bolts
(H3)
4 x Bolts
(H2)
72 x Dowels
(H1) 34 x Cam Nuts
(H4)
4 x Bracket
(H8)
4 x Plastic Glide
(H7)
20 x Screws
(H5) 1 x Allen key
(H6)
Parts list
Top Panel (P1)
Bottom Panel (P2)
Left Legs (P3) x2
Right Legs (P4) x2
Divider Panels (P5) x3
Shelf Middle Panels (P6) x2
Shelf Top Panel (P7) x2
Shelf Bottom Panel (P8) x2
Small Shelf Panel (P9) x2
Side Panels (P10) x2
www.fantasticfurniture.com.au PAGE 4
What you need
to assemble the product
Additional Tools Required
Phillips head screwdriver;
Hammer
DO NOT USE
Hardware pack Bottom Panel
(P2)
Divider
Panel
(P5)
Side
Panel
(P10)
Side
Panel
(P10)
Shelf Top
Panel (P7)
Divider
Panel
(P5)
Left Leg
(P3)
Left Leg
(P3)
Right Leg
(P4)
Right Leg
(P4)
Shelf Bottom
Panel (P8)
2 x Large Screws
(H12)
1 x Safety
Strap
(H9)
2 x Washers
(H11)
1 x Safety
Strap Screw
(H10)
Small Shelf
Panel (P9)
Shelf Middle
Panel (P6)
Shelf Middle
Panel
(P6)
Small Shelf
Panel (P9)
Divider
Panel
(P5)
Shelf Top
Panel (P7)
Shelf Bottom
Panel (P8)

PAGE 5
You will need
Step 1
www.fantasticfurniture.com.au
Phillips head
screwdriver
Step 2
Secure 4 x Cam Bolts (H3) to each Left Leg (P3x2) and 4 x Cam Bolts (H3) to each
Right Leg (P4x2) by tightening Cam Bolts (H3) with a Phillips Head Screwdriver.
Secure 2 x Cam Bolts (H3) to Top Panel (P1) by tightening Cam Bolts (H3) with a
Phillips Head Screwdriver.
H3
You will need
(P3)
(P4)
16 x Cam Bolts
(H3)
Phillips head
screwdriver
2 x Cam Bolts
(H3)
(P1)
H3
H3
H3
H3
H3
H3
H3
H3
H3
x2
x2

www.fantasticfurniture.com.au PAGE 6
Step 3
You will need
You will need
Step 4
Insert 2 x Dowels (H1) into Shelf Top Panel (P7) and attach Divider Panel (P5) with
2 x Screws (H5) by tightening with a Phillips Head Screwdriver. Repeat this step for
the second Shelf Top Panel (P7) and Divider Panel (P5).
H3
H3
H3
H3
H3
H3
(P8)
(P6)
(P7)
Phillips head
screwdriver
16 x Cam Bolts
(H3)
Phillips head
screwdriver
4 x Dowels
(H1) 4 x Screws (H5)
(P5)
(P7)
Secure 2 x Cam Bolts (H3) to each Shelf Middle Panel (P6x2), 2 x Cam Bolts (H3) to each
Shelf Bottom Panel (P8x2) and 4 x Cam Bolts (H3) to Shelf Top Panel (P7) by tightening
Cam Bolts (H3) with a Phillips Head Screwdriver.
H3
H3
x2 x2
x2
H1
H1
H5
H5 x2

Insert 2 x Dowels (H1) into Side Panel (P10) and 2 x Dowels (H1) into Side Middle Panel (P6)
then attach to Shelf Bottom Panel (P8) with 4 x Screws (H5) by tightening with the Phillips Head
Screwdriver. Repeat these steps for second set of panels.
www.fantasticfurniture.com.au PAGE 7
Step 5
You will need
Phillips head
screwdriver
(P7)
(P6)
(P10)
(P6)
(P10)
(P8)
8 x Cam Nuts
(H4)
8 x Dowels
(H1)
You will need
Phillips head
screwdriver
8 x Dowels
(H1) 8 x Screws
(H5)
Insert 2 x Dowels (H1) into Side Panel (P10) and 2 x Dowels (H1) into Side Middle Panel (P6) then
attach to Shelf Top Panel (P7) as shown. Insert 2 x Cam Nuts (H4) into Side Panel (P10) and 2 x Cam
Nuts (H4) into Side Middle Panel (P6). Ensure the arrows on the cam nuts are facing towards the
incoming cam bolts and secure by tightening cam nuts with a Phillips Head Screwdriver. Repeat these
steps for second set of panels.
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
x2
x2
Step 6
H1
H1
H1
H1
H4
H4
H4
H5
H5
H5
H5
H1
H1
H1
H1
H4
H4

www.fantasticfurniture.com.au PAGE 8
Step 7
(P8)
(P8)
(P6)
(P5)
(P10)
(P9)
(P9)
You will need
Phillips head
screwdriver
2 x Cam Nuts
(H4)
2 x Dowels
(H1)
You will need
Phillips head
screwdriver
4 x Cam Nuts
(H4)
4 x Dowels
(H1)
Insert 2 x Dowels (H1) into Divider Panel (P5) then attach to
Shelf Bottom Panel (P8). Insert 2 x Cam Nuts (H4) into Divider Panel (P5).
Ensure the arrows on the cam nuts are facing towards the incoming cam bolts
and secure by tightening cam nuts with a Phillips Head Screwdriver.
Insert 2 x Dowels (H1) into each Small Shelf Panel (P9x2) then attach to Side Middle Panels (P6x2)
as shown. Insert 2 x Cam Nuts (H4) into each Small Shelf Panel (P9x2). Ensure the arrows on the
cam nuts are facing towards the incoming cam bolts and secure by tightening cam nuts
with a Phillips Head Screwdriver.
(P6) (P6)
Step 8
H1
H1 H4
H1
H4
H4
H4
H1
H1
H4
H4

www.fantasticfurniture.com.au PAGE 9
Step 9
(P8) (P5)
(P5)
(P2)
You will need
Phillips head
screwdriver
2 x Cam Nuts
(H4)
2 x Dowels
(H1)
You will need
Phillips head
screwdriver
2 x Dowels
(H1) 2 x Large Screws (H12)
Insert 2 x Dowels (H1) into Divider Panel (P5) then attach to Shelf Bottom Panel (P8).
Insert 2 x Cam Nuts (H4) into Divider Panel (P5). Ensure the arrows on the cam nuts are
facing towards the incoming cam bolts and secure by tightening cam nuts with a Phillips
Head Screwdriver.
Insert 2 x Dowels (H1) into Divider Panel (P5), attach to Bottom Panel (P2) and secure
with 2 x Large Screws (H12) by tightening with a Phillips Head Screwdriver.
Step 10
H1
H1
H4
H1
H12
H12

www.fantasticfurniture.com.au PAGE 10
Step 11
(P3)
(P4)
You will need
Phillips head
screwdriver
8 x Cam Nuts
(H4)
16 x Dowels
(H1)
You will need
Phillips head
screwdriver
8 x Cam Nuts
(H4)
16 x Dowels
(H1)
(P7)
(P7)
(P2)
(P8)
(P8)
(P9)
(P9)
REQUIRED
TWO PEOPLE
REQUIRED
TWO PEOPLE
(P3)
(P4)
(P9)
(P7)
(P8)
(P9)
(P7)
(P8)
(P2)
Insert 8 x Dowels (H1) into Left Leg (P3) and 8 x Dowels (H1) into
Right Leg (P4). Attach Left & Right Legs (P3&P4) to partially assembled
unit as shown. Insert 2 x Cam Nuts (H4) into Bottom Panel (P2), 1 x Cam
Nut (H4) into each Shelf Bottom Panel (P8x2), 1 x Cam Nut (H4) into each
Small Shelf Panel (P9x2), and 1 x Cam Nut (H4) into each Shelf Top Panel (P7x2) as shown.
Ensure the arrows on the cam nuts are facing towards the incoming cam bolts and secure by
tightening cam nuts with a Phillips Head Screwdriver.
Carefully turn the bookcase over. Insert 8 x
Dowels (H1) into Left Leg (P3) and 8 x Dowels (H1)
into Right Leg (P4). Attach Left & Right Legs (P3&P4) to
partially assembled unit as shown. Insert 2 x Cam Nuts (H4)
into Bottom Panel (P2), 1 x Cam Nut (H4) into each Shelf Bottom
Panel (P8x2), 1 x Cam Nut (H4) into each Small Shelf Panel (P9x2),
and 1 x Cam Nut (H4) into each Shelf Top Panel (P7x2) as shown. Ensure
the arrows on the cam nuts are facing towards the incoming cam bolts and secure
by tightening cam nuts with a Phillips Head Screwdriver.
Step 12
H1
H4
H4
H4
H4
H4
H4
H4
H4
H1
H4
H4
H4
H4
H4
H4
H4
H4
H1
H4
H1
H4