fantastic furniture VISION User manual

Assembly Instructions
VISION
Display Cabinet
TEMPERED GLASS SHOULD ALWAYS BE
HANDLED WITH CARE
Ver:1.1

Read Instructions carefully.
Check no parts are missing
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Separate and identify each component from the
hardware pack and rest each one in its proper
location before fastening.
DO NOT fully tighten screws (leave slightly
loose). When the item is fully assembled
tighten the screws –but do not over tighten.
DO NOT set glue until you are certain that the
parts belong together.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Page 2

As wall materials vary, screws for fixing to wall are
not included. For advice on suitable screw systems,
contact your local specialised dealer.
TEMPERED GLASS should be handled with care. Scratches,
chips, sudden changes in temperature, hairline fractures or other
minor impurities may cause the glass to break suddenly and
without warning. This glass is designed to break into small,
relatively harmless pieces and not sharp fragments.
Care Instructions:
- Wipe clean with a cloth dampened in water or window cleaner
only.
-Wipe dry with a clean cloth.
Good to know:
- Never place extremely hot or cold objects directly onto the
glass surface. This may weaken the integrity of the glass and
cause it to break suddenly and without warning.
- Dropping heavy, glass, ceramic, metal or similar objects on the
table may cause unseen damage to the table leading it to
break suddenly and without warning.
Page 3

Top (P5)
Side Panel
(P4)
Side Panel
(P4)
Shelf (P7)
Door
(P6)
Base (P1)
Back
(P2)
Joiner strip
(P3)
(Tools are not provided)
Phillips screwdriver
What You Need
Page 4
4 x Rear Corner Brackets
(H1)
4 x Front brackets
(H2)
8 x M3 x 13 mm Screws
(H3)
12 x Bolts
(H4)
4 x Feet
(H5)
4x M4 x 22 mm Screws
(H6)
12 x Shelf lugs
(H7)
2 x Magnetic Catch
(H9)
1 x Door handle/Foam Insert
(H11) 1 x Wall Strap
(H12)
1x M4 x 14 mm Screws
(H13)
2 x Washer
(H14)
1 x Strike Plate/Foam Insert
(H10)
2 x Sleeve
(H15)
Please make sure you have all these parts before you start
Joiner Strip
(P3)
Shelf (P7)
Shelf (P7)
2 x Door hinges
(H8)

Step 1
Step 2
4x M4 x 22 mm
Screws
(H6)
4 x 20 x 44 mm
Feet
(H5)
You will need:
Back
(P2)
Base
(P1)
Base
(P1)
H5
H5
H6
H5
H6
H5
H6
Page 5
Attach Feet (H5) to Base (P1) using 4 x Screws (H6) and tighten using phillips head screwdriver.
Turn the Base (P1) to let it stand on its feet.
Insert one short edge of Back Panel (P2) into the groove of Base (P1)
H6

Step 3
Step 4
Back
(P2)
Base
(P1)
Strip Joiner
(P3)
Side Panel
(P4) Side Panel
(P4)
Page 6
With the help of another person, attach 2x Strip Joiners (P3) to the sides of Back Panel (P2).
Insert one short edge of Side Panel (P4) into the groove of Base (P1) and the adjacent
long edge into the Strip Joiner (P3). Repeat with the other Side Panel (P4).
Base
(P1)

Top (P5)
Side
Panel
(P4)
Side
Panel
(P4)
Back
(P2)
Step 5
Step 6
4 x
Front brackets
(H2)
8 x M3 x 13 mm
Screws
(H3)
12 x
Bolts
(H4)
4 x
Rear Corner Brackets
(H1)
You will need:
H4
H3
H4
H3 H2
H4
H4
H1
H3
Page 7
Place Top (P5) so that the top edges of the two Side Panels (P4) and Back (P2) are in the grooves
of Top (P5)
Attach 4 x Rear Corner Brackets (H1) to Back (P2), Side Panels (P4), Top (P5) and Base (P1) with
4 x Screws (H3) and 8 x Bolts (H4).
Top (P5)
Base (P1)
Side
Panel
(P4) Side
Panel
(P4)
Back
(P2)
Attach 4 x Front Brackets (H2) to Side Panels (P4), Top (P5) and Base (P1) with
4 x Screws (H3) and 4 x Bolts (H4).

Step 7
Step 8
12 x
Shelf lugs
(H7)
2x
Door Hinges
(H8)
You will need:
You will need:
H7 H7
Door (P6)
Note: This installs the door to open from the left.
To install the door to open from the right, install the Catch (H9) on the right side.
2 x
Magnetic Catch
(H9)
H9
H9
H8
Page 8
Insert a magnetic catch (H9) each into the top (P5) and Base (P1).
Attach 12 x shelf lugs (H7) to the side panels (P4).
Top (P5)
Base (P1)
Side
Panel
(P4)
Side
Panel
(P4)
Back
(P2)
Peel off the backing from foam inserts and paste them on two corners of the Door (P6).
Attach the Door Hinges (H8) to the Door (P6) using the hinge bolts with a Phillips screw driver.

You will need:
Step 9
Step 10
1x
Door Handle/Foam Insert
(H11)
You will need:
1 x
Strike Plate/Foam Insert
(H10)
H10
H11
Note:
This installs the door to open from the left.
If you have set up the magnetic catches in step 7
to open from the right, please install the door
from the left side.
H10
2 x
Sleeve
(H15)
Door
(P6)
H15
Page 9
Loosen the door hinge (H8) on the top of Door (P6) with a Phillips screw driver.
Insert the top hinge into the sleeve (H15) on the Top (P5).
Slide the top corner of Door (P6) into the hinge.
Tighten the bolts on the top door hinge with a Phillips screw driver.
Remove the foam insert from the Strike Plate (H10).
Peel off the backing from foam insert and paste it onto the bottom
corner of the Door (P6). Slide the Strike Plate (H10) into position.
Repeat with the Door Handle (H11) at the top corner of the door.
Insert a Sleeve (H15) each into the Top (P5) and
Base (P1).
Place the door (P6) with its hinge into the Sleeve
(H15) in base (P1).
H15

Step 11
Step 12
You will need:
1 x
Wall Strap
(H12)
It is recommended that the unit is fixed to a wall.
As wall materials vary, screws for fixing to wall are not
included. For advice on suitable screw systems, contact your
local specialised dealer.
H12
Page 10
F
Shelf
(P7)
Shelf
(P7)
Shelf
(P7)
Move the cabinet to the desired position against a wall.
Mark a line on the wall at the center top edge of the cabinet.
Remove the cabinet, mark a point about 10 cm below the line.
Attach the wall strap (H12) with the appropriate screw system and
washer (H14).
Carefully move each Shelf (P7) into the cabinet above the
lugs. Place each Shelf (P7) onto the lugs, making sure it
sits firmly on all four lugs.
1 x
Washer
(H14)