fantastic furniture Como Dresser 3 Drw User manual

Version 1.0
Como
Dresser 3 Drw
fantasticfurniture.com.au

fantasticfurniture.com.au Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 18kgs/Drawer.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Left Side Panel (P2);
Right Side Panel (P3);
2 x Rails (P4);
Rail (P5);
Rail (P6);
Rail(P7);
Rail (P8)
2 x Back Panels (P9);
Connect Stick (P10);
3 x Drawer Front (P11);
3 x Left Drawer Side (P12);
3 x Right Drawer Side (P13)
3 x Drawer Base (P14);
3 x Drawer Back (P15);
3 xSupport Rail (P16)
Hardware pack
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
Left
Drawer
Side (P12)
Drawer Front
(P11)
×3
Right Drawer
Side (P13)
Drawer Back
(P15)
Drawer
Base (P14)
Support
Rail
(P16)
Top Panel
(P1)
Right Side
Panel
(P3)
Left Side
Panel
(P2)
Rail
(P4)
Rail
(P4)
Rail
(P5)
Rail
(P6)
Rail
(P7)
Rail
(P8)
2 x Back
Panels
(P9)
Connect Stick
(P10)
25 x Dowels
(H1)
18 x Long Screws
(H2)
48 x Small Screws
(H5)
3 x CL Runner
Tracks
(H6)
12 x Cam Bolts
(H3)
12 x Cam Nuts
(H4)
15 x Small
Cam Nuts
(H11)
3 x CR Runner
Tracks
(H7)
3 x DL Runners
(H8)
3 x DR Runners
(H9)
15 x Small
Cam Bolts
(H10)
4 x Plastic
Glides
(H15)
1 x Screw
(H13)
1 x Safety Strap
(H12)
2 x Washers
(H14)

You will need
Step 3
8 x Dowels
(H1)
Phillips Head
Screwdriver
8 x Cam Bolts
(H3)
H5
H5
H6
H6
H6
H5
H5
H5
H5
H5
H5
H5
H6
CL
H5
H5
H5
H5
H5
H5
H5
H5
H7
H7
H7
H5
H5
(P3)
H7
CR
H5
H3
H3
H3
(P3)
(P2)
H1
H1
H1
H1
H1
H1
H3
H1
H1
H3
H3
H3
H3
9 x Small
Screws (H5)
9 x Small
Screws (H5)
(P2)
Attach 3 x CL Runner Tracks (H6) to Left Side Panel (P2) with 9 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
Attach 2 x CR Runner Tracks (H7) to Right Side Panel (P3) with 6 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au Page 5
Insert 8 x Dowels (H1) into Left Side Panels (P2).
Attach 8 x Cam Bolts (H3) into Side Panels (P2) and (P3) as shown..
You will need
Step 2
Phillips Head
Screwdriver
You will need
Step 1
Phillips Head
Screwdriver
3 x CL Runne
Tracks (H6)
3 x CR Runne
Tracks (H7)

Step 5
You will need
8 x Dowels
(H1)
4 x Cam Nuts
(H4)
Phillips Head
Screwdriver
Step 4
You will need
4 x Cam Nuts
(H4)
Phillips Head
Screwdriver
Insert 4 x Cam Nuts (H4) into the holes of Rails (P5)
and (P6,P7,P8).Rotate the cam nuts so the arrows point
towards the incoming cam bolts. Attach 2 x Rails (P4), Rails (P5) and (P6,P7,P8) to
Left Side Panel (P2), then tighten the cam nuts..
Insert 8 x Dowels (H1) into 2 x Rails (P4) and
(P5,P6,P7,P8).Insert 4 x Cam Nuts (H4) into
the holes of Rails (P5) and (P6,P7,P8).Rotate
the cam nuts so the arrows point towards the
incoming cam bolts.Push Right Side Panel (P3)
into place and tighten the cam nuts..
(P2)
(P5)
(P4)
(P4)
(P6)
(P8)
(P7)
H4
H4
H4
H4
(P2)
(P3)
(P5) (P4)
(P4) (P6) (P8)
(P7)
H4
H4
H4
H1 H1
H1
H1
H1
H1
H1
H4
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
fantasticfurniture.com.au Page 6
H4

Step 7
You will need
Phillips Head
Screwdriver
You will need
Step 6
Join 2 x Back Panels (P9) with Connect Stick (P10),then put into the groove on the back of
the chest,screw it with 18 x Small Screws (H5)
Hammer 4 x Plastic Glides (H15) on Side Panels (P2) and (P3)
(P2)
(P3)
H5
H5
(P9)
(P9)
(P10)
4 x Plastic
Glides (H15) Hammer
fantasticfurniture.com.au Page 7
18 x Small
Screws (H5)
H15
20mm
H15
H15
H15
H15

Attach 4 x Cam Bolts (H3) into Top Panel (P1) as shown.
(P2)
(P3)
H1
H1
H4
H4
H4
H1
Insert 6 x Dowels (H1) into Side Panels (P2,P3) and Rail (P7).
Insert 4 x Cam Nuts (H4) into the holes of Side Panels (P2) and (P3).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Top Panel (P1) and tighten the cam nuts.
Step 8
You will need
Phillips Head
Screwdriver
4 x Cam Bolts
(H3)
fantasticfurniture.com.au Page 8
(P1)
H3
H3
H3
H3
You will need
Step 9
Phillips Head
Screwdriver
4 x Cam Nuts
(H4)
6 x Dowels
(H1)

Insert 5 x Small Cam Nuts (H11) into the
holes ofDrawer Sides (P12,P13) and Support
Rail (P16). Rotate the cam nuts so the arrows
point towards the incoming cam bolts.Push
Drawer Sides (P12,P13) and Support Rail (P16)
into place and tighten the cam nuts..
H10
H10
(P11)
H10
H10
H10
H1
Insert 1 x Dowel (H1) into Drawer Front (P11) Attach 5 x Small Cam Bolts (H10) as shown.
fantasticfurniture.com.au Page 9
You will need
Step 11
Phillips Head
Screwdriver
5 x Small Cam
Nuts (H11)
You will need
Step 10
5 x Small Cam
Bolts (H10)
1 x Dowel
(H1)
Step 12
Slide Drawer Base (P14) into the groove
in Drawer Sides (P12) and (P13) .
H11
H11
H11
(P11)
(P12)
(P16)
(P13)
H11 H11
(P11)
(P14)
(P12)
(P13)
Phillips Head
Screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.

fantasticfurniture.com.au Page 10
You will need
Step 13
Phillips Head
Screwdriver
You will need
Step 14
Step 15
4 x Small
Screws (H5)
Phillips Head
Screwdriver
1 x DR
Runner (H9)
1 x DL
Runner (H8)
Attach Drawer Back (P15) to Drawer Sides (P12,P13)with 4 x Long Screws (H2), then attach
Drawer Back (P15) to Support Rail (P16) with 2 x Long Screws (H2). Make sure that the groove
lines up the whole way around the drawer.
H9
H8
DR
DL
H5
H5
H5
H5
H2
H2H2
(P15)
(P12)
(P13)
H2
H2
H2H2
(P15)
(P12)
(P13)
H2
H2
H2
6 x Long
Screws (H2)
H2
H2
Attach 1 x DL Runner (H8) to the bottom of Left Drawer Side (P12)
and 1 x DR Runner (H9) to the bottom of Right Drawer Side (P13) with
4 x Small Screws (H5).
Repeat step 10 to step 14 to
assemble other drawers.

fantasticfurniture.com.au
Step 16
Page 11
Please make sure your chest is sitting squarely on the floor, then tighten
all the screws and bolts – being careful not to over tighten
Insert the assembled drawers into the corresponding compartments as shown.
Ensure the drawers slide easily along the rails.

H12
H13
H14
fantasticfurniture.com.au Page 12
You will need
Step 17
Phillips Head
Screwdriver
Attach Safety Strap (H12) to the Top Panel (P1) using 1 x Screw (H13) and 1 x Washer (H14)
1 x Safety Strap
(H12)
1 x Screw
(H13)
1 x Washer
(H14)
Move the chest to the final position. Attach the safety strap to the wall.
Make sure it is firmly attached and make sure it is snug fit.
Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
We strongly advise that you use
the wall safety strap provided to
prevent the unit toppling
Seek advice from a qualified
trades person on how to
attach this safety strap to
your specific wall.
wall
Screw
H14
Phillips Head
Screwdriver
You will need
Step 22
1 x Washer
(H14)
Screw and Wall Plug
are not provided.
Please use appropriate
fixtures for your wall.