fantastic furniture Forbes Credenza File Cabinet User manual

Forbes
Version 1.0
www.fantasticfurniture.com.au
Credenza File Cabinet

Enjoy
Your purchase from
Australia’s Best Value Furniture Store
www.fantasticfurniture.com.au PA E 2

www.fantasticfurniture.com.au PA E 3
Assembly checklist
Useful Information
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label ot website for
product care instructions.
!if you are having any difficulties assembling your product, missing any hardware or components
please visit our website Help Centre for further assistance.
Read through the instructions carefully
before you begin
Make sure you have all the requires tools.
Never use power tools unless instructed.
Identify and lay out all of the components
before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.

P1
P3
P4
P2
P5
P11
P6
P7
What you need
To assemble the product
Parts List
Base Panel (P1); Left Side Panel (P2); Right Side Panel (P3); Left Side Division (P4); Right Side
Division (P5); Left And Right Back Panel (P6); Centre Back Panel (P7); Adjustable Shelves (P8);
Fixed Middle Shelf (P9); Top Panel (P10); Left & Right Side Door (P11); Small Drawer Front (P13);
Large Drawer Front (P14); Drawer Sides (P15); Small Drawer Back (P16); Large Drawer Back
(P17); Drawer Bottoms (P18)
www.fantasticfurniture.com.au PA E 4
P8
P8
P6
P9
P10
P11
P13
P14
P15 P16
P17

12 x CONFIRMAT SCREWS
(H2)
8 x CONFIRMAT SCREW
CAPS (H3)
2 x LUE
(H4)
62 x WOODEN DOWELS
(H5)
24 x 13mm C/S SCREWS
(H1)
2 x PAIRED DRAWERS
RUNNERS (H6)
2 x FILE RODS (H10)
8 x EURO SCREWS
(H7)
www.fantasticfurniture.com.au PA E 5
Hardware
24 x 5/8 PAN HEAD SCREWS
(H9)
6 x CASTER WHEEL
(H8)
8 x SELF SUPPORTS
(H11) 4 x HIN E BLOCK &
HIN E (H12)
4 x FORBES HANDLE
(H13)

STEP 1
P3
You will need:
4 x Hinge Block (H12) 1 x Glue (H4)
8 x Wooden Dowels (H5)
Raw Edge
Top
1 Insert a small amount of lue (H4) into the holes provided in the top of
panels P2 & P3.
2. Insert the Wooden Dowels (H5) into the holes that you have just put
glue into and tap in with a mallet.
3. Fix the Hinge Blocks (H12) to P2 & P3 . As per picture
www.fantasticfurniture.com.au PA E 6
Raw Edge
P2
When attaching the hinge
lock (H12) ensure that it is
positioned as shown a ove.
FACING
FRONT
OF UNIT
FACING
REAR OF
UNIT
Front Edge Front Edge

1 Insert a small amount of lue (H4) into the holes provided in the top and
bottom of panels P4 & P5.
2. Insert the Wooden Dowels (H5) into the holes that you have just put
glue into and tap in with a mallet.
3. Using the flat side of the drawer runners (H6), fix Drawer runner to P4 &
P5 using the Euro Screws (H7).
*** NOTE: line up the holes on the runner to the holes on P3 & P4 rom
the second (2nd) hole rom the wheel on the runner and make sure the
wheel o the runner is closest to the edged side***
EURO SCREWS
HOLES 2 & 11
P4 & P5
STEP 2
You will need:
4 x Drawer runners (H6) 1 x Glue (H4)
8 x Euro screws (H7) 16 x Wooden Dowels (H5)
www.fantasticfurniture.com.au PA E 7
P5
P4
Raw Edge Raw Edge
Front Edge Front Edge

STEP 3
You will need:
1 x Glue (H4) 14 x Wooden Dowels (H5) 4 x Confirmat Screws (H2) 4 x Confirmat
Screw Caps (H3)
1 Insert a small amount of lue (H4) into the holes provided on both
sides of panel (P7 and P9)
2 Insert the Wooden Dowels (H5) into the holes that you have just put
glue into and tap in with a mallet.
3 Insert a small amount of glue into the holes provided in panels P4 & P5
4 Align dowels on P7 & P9 with holes on P4 and bring together.
5 Align dowels on P7 & P9 with holes on P5 and bring together.
6. Using 4 x Confirmat screws (H2) fix panels P4 & P5 in place.
7 Insert Confirmat End Caps (H3) into the screws
LUE ALL DOWEL JOINTS
P4
P9
P7
www.fantasticfurniture.com.au PA E 8
P5

P4
P9
P5
P1
STEP 4
You will need:
1 x Glue (H4) 8 x Wooden Dowels (H5) 4 x Confirmat Screws (H2)
LUE ALL DOWEL JOINTS
1 Insert a small amount of lue (H4) into the holes provided in the sides
of panel (P1)
2 Insert the Wooden Dowels (H5) into the holes that you have just put
glue into and tap in with a mallet.
3 Insert a small amount of lue (H4) into the larger holes provided in P1
4 Align dowels on P4 & P5 with holes on P1 and bring together
5 Using 4 x Confirmat screws (H2) fix panels P4 & P5 in place
through the bottom of P1
www.fantasticfurniture.com.au PA E 9

STEP 5
www.fantasticfurniture.com.au PA E 10
You will need:
1 x Glue (H4) 16 x Wooden Dowels (H5)
LUE ALL DOWEL JOINTS
P1
P4
P5
P9
P6
P6
1 Insert a small amount of lue (H4) into the holes provided in the sides
of panels (P6)
2 Insert the Wooden Dowels (H5) into the holes that you have just put
glue into and tap in with a mallet.
3 Align dowels on P6 with holes on P4 & P5 and bring together

STEP 6
www.fantasticfurniture.com.au PA E 11
LUE ALL DOWEL JOINTS
P1
P4
P5
P9
P6
1 Insert a small amount of lue (H4) into the holes provided on panel P2 & P3
2 Align dowels on P1 & P6 with holes on P2 & P3 and bring together
3 Using 4 x Confirmat screws (H2) fix panels P2 & P3 in place.
4 Insert Confirmat End Caps (H3) into the screws
P6
P2
P3
You will need:
1 x Glue (H4) 4 x Confirmat Screws (H2) 4 x Confirmat Screw Caps (H3)

STEP 7
You will need:
1 x Glue (H4)
LUE ALL DOWEL JOINTS
www.fantasticfurniture.com.au PA E 12
P1
P10
P4
P5
P9
P6
P6
P2
P3
1 Insert a small amount of lue (H4) into the holes provided on panel P10
2 Align dowels on P2, P3, P4 & P5 with holes on P10 and bring together

STEP 8
You will need:
6 x Castor Wheel (H8) 24 x 5/8 Pan Head Screws (H9)
P1
P2
P3 P10
P5
P4
P9
1 Carefully place the unit onto its back
2 Using the holes provided in the bottom of P1, fix 6 x Castor Wheels (H8)
onto P1 using the 5/8 Pan Head Screws (H9)
www.fantasticfurniture.com.au PA E 13

STEP 9
You will need:
2 x Drawer runners (H6) 1 x Glue (H4)
4 x 13mm C/S screws (H1)
1 Insert a small amount of glue into the dowel holes provided on the
Drawer Front (P13) and the Drawer Back (P16).
2 Align dowels on drawer side (P15) with holes on Drawer Front (P13)
and bring together. Slide the Drawer Bottom (P18) into the groves on
the Drawer Sides (P15) making sure it finishes in the grove of the
Drawer Front (P13).
3. Align dowels on drawer side (P15) with holes on Drawer Back (P16)
and bring together.
2 Using the angled part of the drawer runners (H6), fix Drawer runners
(H6) to base of drawer AS SHOWN using the 13mm C/S Screws (H1).
Drawer Back
www.fantasticfurniture.com.au PA E 14
P15
P13
P16
P18

STEP 10
1 Insert a small amount of glue Into the dowel holes provided on the File
Drawer Front (P14) and the File Drawer Back (P17)
2 Align dowels on Drawer side (P15) and File Rod (H9) with holes on File
Drawer Front (P14) and bring together. Slide the Drawer Bottom (P18)
into the groves on the Drawer Sides (P15) making sure it finishes in the
grove of the Drawer Front (P14).
3. Align dowels on drawer side (P15) and File Rod (H9) with holes on
Drawer Back (P17) and bring together.
4 Using the angled part of the drawer runners (H6), fix Drawer runners
(H6) to base of drawer AS SHOWN using the 13mm C/S Screws (H1).
You will need:
2 x Drawer runners (H6) 1 x Glue (H4)
4 x 13mm C/S screws (H1) 2 x File Rods (H9)
www.fantasticfurniture.com.au PA E 15
P17
P14
P15
P18

STEP 11
You will need:
2 x For es Handle (H13) 4 x 13mm C/S Screws (H1) 8 x Shelf Supports (H11)
www.fantasticfurniture.com.au PA E 16
1 Using the holes provided on the back of both Drawer Fronts, fix Forbes
Handle (H13) to the top of the Drawer Fronts using the 13mm C/S Screw
(H1)
2 Using the holes provided in Panels P2, P3, P4, P5, insert the self supports
into the holes making sure that you use the corresponding hole on the
opposite panel. Insert Shelf P8 into unit.
P1
P10
P4
P14
P9
P8
P8
P2
P3
P13

STEP 12
1 Repeat the previous step to fix Forbes Handles (H13) to Doors P11 & P12
2 Attach hinge (H10) to doors (P11 & P12) using the 8 x 13mm C/S
Screw (H9) using the pilot holes as shown in picture above.
3 Working from the top down, Position the Hinge (H10) and the Hinge Block
(H10) together from the front of the Hinge Block first then simply click
together.
You will need:
4 x Hinge (H10)
8 x 13mm C/S Screw (H1)
2 x For es Handle (H13)
13mm C/S Screw
(H1)
Hinge (H10)
P11 & P12
Adjustment of Doors (More information on page 12)
Snap On System
The hinge arm is positioned on the mounting
plate and simply clipped on from front to
ack.
It can easily e removed from the mounting
plate y pressing the ack end of the hinge
arm which will release it from the lock
www.fantasticfurniture.com.au PA E 17

STEP 13
www.fantasticfurniture.com.au PA E 18

In the interest of our environment
Please dispose of all packaging thoughtfully.
www.fantasticfurniture.com.au PA E 19
Your Unit Is Now Complete