Feig Electronic ID ISC.ANT.U500/270 User manual

INSTALLATION
final - public (B)
2018-04-18 –M71110-0e-ID-B.doc
ID ISC.ANT.U500/270
Type DM Direction Mode

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 2 of 48
M71110-0e-ID-B.doc
Note
Copyright 2017 by
FEIG ELECTRONIC GmbH
Lange Strasse 4
D-35781 Weilburg
Tel.: [phone]
http://www.feig.de
With the edition of this document, all previous editions become void. Indications made in this manual may be
changed without previous notice.
Copying of this document, and giving it to others and the use or communication of the contents thereof are
forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved
in the event of the grant of a patent or the registration of a utility model or design.
Composition of the information in this document has been done to the best of our knowledge. FEIG
ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this
manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,
despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.
The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC
GmbH does not give any guarantee promise for perfect function in cross environments and does not give
any guaranty for the functionality of the complete system which incorporates the subject of this document.
FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed
with components and testing methods for a level of reliability suitable for use in or in connection with surgical
implants or as critical components in any life support systems whose failure to perform can reasonably be
expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application
designer must take reasonably prudent steps to protect against system failures.
FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this docu-
ment and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does
not convey any license under its patent rights nor the rights of others.
OBID®and OBID i-scan®are registered trademarks of FEIG ELECTRONIC GmbH.
my-d®is a registered trademark of Infineon Technologies AG
I-CODE®is a registered trademark of Philips Electronics N.V.
Tag-itTM is a registered trademark of Texas Instruments Incorporated.
General information's regarding this document
The sign "" indicates extensions or changes of this manual compared with the former issue.
If bits within one byte are filled with "-", these bit spaces are reserved for future extensions or for internal
testing- and manufacturing-functions. These bit spaces must not be changed, as this may cause faulty
operation of the reader.
The following figure formats are used:
0...9: for decimal figures
0x00...0xFF:for hexadecimal figures,
b0...1 for binary figures.
The hexadecimal value in brackets "[ ]" marks a control byte (command).

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 3 of 48
M71110-0e-ID-B.doc
Contents
ID ISC.ANT.U500/270 1
Type DM Direction Mode 1
1Safety Instructions / Warning - Read before Start-Up ! 5
2Maintenance 6
3Performance Features 7
3.1 Scope of delivery........................................................................................................ 7
3.1.1 Antenna ID ISC.ANT.U500/270 Type DM (Direction Mode)......................................7
3.2 Performance Features of the ID ISC.ANT.U500/270 Antennas ................................ 7
3.3 Available Antenna Types ...........................................................................................8
4Installation and Wiring 9
4.1 Mounting Preparation................................................................................................ 9
4.2 Installing the antenna............................................................................................... 10
4.2.1 Dimensions of the antenna..................................................................................... 10
4.2.2 Drilling the Mounting Holes ....................................................................................11
4.2.3 Installing the Antenna on the wall or ceiling............................................................12
4.2.4 Disassembly of the Antenna (for replacement/repair).............................................16
5Typical Antenna Configuration 18
5.1 Project Notes Antenna .............................................................................................18
5.2 Antenna Configuration and Setup the Antenna......................................................21
5.2.1 Required Components ...........................................................................................21
5.2.2 Configuration of the Antenna..................................................................................22
5.2.3 Interface Connections ............................................................................................23
5.2.3.1 LAN / TCP/IP................................................................................................23
5.2.3.1 USB Mini Interface on connector X3.............................................................24
5.2.4 Digital Input / Output ..............................................................................................25
5.2.4.1 Digital Input on connector X4........................................................................25
5.2.4.1 Digital Output on connector X4.....................................................................26
5.2.4.1 DC Output on connector X4..........................................................................27
5.2.5 Reader/Antenna Configuration...............................................................................28
5.3 Testing the Gate Antenna.........................................................................................32
5.3.1 Reading a Serial Number.......................................................................................32

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 4 of 48
M71110-0e-ID-B.doc
5.3.2 Testing the performance ........................................................................................33
5.3.3 Reducing false readings......................................................................................... 34
5.3.4 Using the Trigger function with the digital Input......................................................36
5.4 Activating the Automatic Mode................................................................................38
5.4.1 Testing the antenna in Buffered Read Mode..........................................................38
5.4.2 Configuration and Test in Notification Mode...........................................................40
5.5 Reader Diagnostic .................................................................................................... 42
6Configure the reader in accordance with national RF regulations 44
6.1.1 EU reader according to EN 302 208.......................................................................44
6.1.2 FCC Reader according to FCC 47 Part 15.............................................................46
7Technical Data 47
7.1 Antenna ID ISC.ANT.U500/270 Type DM.................................................................. 47

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 5 of 48
M71110-0e-ID-B.doc
1 Safety Instructions / Warning - Read before Start-Up !
The device may only be used for the intended purpose designed by for the manufacturer.
The operation manual should be conveniently kept available at all times for each user.
Unauthorized changes and the use of spare parts and additional devices which have not been
sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such
unauthorized measures shall exclude any liability by the manufacturer.
The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid
for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors,
or omissions in the manual or automatically set parameters for a device or for an incorrect
application of a device.
Repairs may only be executed by the manufacturer.
Installation, operation, and maintenance procedures should only be carried out by qualified
personnel.
Use of the device and its installation must be in accordance with national legal requirements
and local electrical codes .
When working on devices the valid safety regulations must be observed.
Please observe that some parts of the device may heat severely.
Before touching the device, the power supply must always be interrupted. Make sure that the
device is without voltage by measuring. The fading of an operation control (LED) is no indicator
for an interrupted power supply or the device being out of voltage!
For installation and dismantling you should wear suitable safety gloves, because parts of an-
tenna housing could be sharp-edged.
The Antenna is not water proof and should not be exposed to rain or humidity.
Under extreme circumstances water could seep into the antenna and damage the electronic
circuits.
Special advice for wearers of cardiac pacemakers:
Although this device doesn't exceed the valid limits for electromagnetic fields you should
keep a minimum distance of 25 cm between the device and your cardiac pacemaker and
not stay in an immediate proximity of the reader’s antennas for any length of time.
CAUTION! Do not look directly into the Alarm LED light. There is a danger of
injury of the eyes!

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 6 of 48
M71110-0e-ID-B.doc
2 Maintenance
The antenna ID ISC.ANT.U500/270 is a design product with high quality surfaces, and should al-
ways be handled with caution. The antenna was designed to work reliably and flawlessly for years
without special maintenance.
Attention! The surfaces should be cleaned with a clean, soft cloth dampened in a
dishwashing liquid –water solution. The use of alcohol, spirit, thinners, glass clean-
ers or other harsh cleaning liquids is prohibited and will damage the surface.
To improve the durability and the appearance, please follow the instructions below:
Keep the antenna clean and take care the antenna is not scratched. Also regularly apply spe-
cific antistatic products for acrylic surfaces.
Regularly remove dust and other impurities with a soft cloth and a solution of water with a little
dishwashing liquid.
Keep the antenna dry. All kinds of moisture should be avoided during operation and storage.
Precipitation, humidity and liquids contain minerals that will corrode electronic circuits and
damaging transparent plastic parts.
Protect the antenna from high temperatures. Mount the antenna away from heaters and other
heat sources. Operation under direct sunlight can cause extreme high temperatures and a fad-
ing cause of the surface.
Avoid storing or operating the antenna at dirty or wet locations. The surfaces or electronic
components may be-damaging.
Handle the device with care. Shocks may break internal circuit boards.
Do not try to open the antenna during operation or outside maintenance periods. Non-
professional management can result in damage to the device.
If any device not working properly, please contact the appropriate representative.

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 7 of 48
M71110-0e-ID-B.doc
3 Performance Features
3.1 Scope of delivery
3.1.1 Antenna ID ISC.ANT.U500/270 Type DM (Direction Mode)
Antenna ID ISC.ANT.U500/270 incl. UHF Reader Module and Mounting bracket.
Mounting Instruction
3.2 Performance Features of the ID ISC.ANT.U500/270 Antennas
The ID ISC.ANT.U500/270-DM (Direction Mode) antenna is a version with integrated Long Range
Reader ID ISC.LRU1002
Depending on the antenna configuration, one, two or all three read orientations of the Smart Tags
and various distances are possible.
The antenna can be used for detecting both product and persons. Another feature is that the
antenna gives the information of the moving direction of the detected transponders when passing
the antenna.
It is for indoors use, only.

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 8 of 48
M71110-0e-ID-B.doc
3.3 Available Antenna Types
The following products are currently available:
Antenna Type
Description
ID ISC.ANT.U.500/270-DM
FCC
Order No. 4922.000.00
Antenna with Reader, Multiplexer and Mounting bracket
ID ISC.ANT.U500/270-DM
EU
Order No. 4923.000.00
Antenna with Reader, Multiplexer and Mounting bracket
ID NET.24V-B
Order No. 2557.000.00
Power Supply without power cable.
ID CAB.NET.24V-B-EU
Order No. 2558.000.00
Cable with European Plug
ID CAB.NET.24V-B-GB
Order No. 2559.000.00
Cable with GB/UK Plug
ID CAB.NET.24V-B-US
Order No. 2560.000.00
Cable with US Plug
Table 1: Available Antenna Types and Accessories

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 9 of 48
M71110-0e-ID-B.doc
4 Installation and Wiring
4.1 Mounting Preparation
For the assembly of the antenna it has to be carefully unpacked. This is done as described in the
following steps:
Place the packed antenna on the floor or table with the top side facing up. Carefully open the box
and then remove the antenna. Remove the mounting bracket from the antenna and use it as
drilling template.
Fig. 1: Packed Antenna

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 10 of 48
M71110-0e-ID-B.doc
4.2 Installing the antenna
4.2.1Dimensions of the antenna
The overall dimensions of the antenna are shown in Fig. 2
Fig. 2: Antenna outside dimensions
All dimensions are in mm with general tolerance according to ISO 2768 m (mean).

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 11 of 48
M71110-0e-ID-B.doc
4.2.2Drilling the Mounting Holes
If the position of the antennas has been marked or determined, the mounting holes can be marked
and drilled for the antenna mounting bracket. The mounting bracket could be used as drilling
template. It is also possible to mount the antenna bracket to a VESA bracket.
The dimensions are shown in Fig. 3:
Fig. 3: Mounting bracket dimensions
All dimensions are in mm with general tolerance to ISO 2768 m (middle)

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 12 of 48
M71110-0e-ID-B.doc
4.2.3Installing the Antenna on the wall or ceiling
The antenna could be mounted on the floor or ceiling with the mounting bracket directly or with the
use of a VESA bracket.
Step
Action
Note
1
Do not open the antenna
body !
2
Place the antenna with its
front side carefully on a desk
or a soft ground.
3
Unscrew the 4 screws of the
mounting bracket.
Do not remove !

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 13 of 48
M71110-0e-ID-B.doc
Step
Action
Note
4
Pull the mounting bracket
from the antenna housing.
5
Install the mounting bracket
at its position.
e.g. Here at the wall at 85cm
85cm

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 14 of 48
M71110-0e-ID-B.doc
Step
Action
Note
6
Hang the antenna on the
mounting bracket and fix the
antenna body at the
mounting bracket with the 4
screws.
1.
2.

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 15 of 48
M71110-0e-ID-B.doc
Step
Action
Note
7
Remove the plugs and make
the needed cabling.

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 16 of 48
M71110-0e-ID-B.doc
4.2.4 Disassembly of the Antenna (for replacement/repair)
Step
Action
Note
1
Do not open the antenna
body !
2
Remove the plugs and all
cable connections.
3
Unscrew the 4 screws of the
mounting bracket.
Do not remove !

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 17 of 48
M71110-0e-ID-B.doc
Step
Action
Note
4
Pull the antenna upwards
and away from the wall.
1.
2.

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 18 of 48
M71110-0e-ID-B.doc
5 Typical Antenna Configuration
The standard configuration of the antenna with three-dimensional tag orientation consists of one
ID ISC.ANT.U500/270-DM antenna with reader. If a tag moves, at horizontal line through the
detection area, it can be detected with a high reliability. Best performance could be achieved if the
antenna is mounted on the ceiling.
5.1 Project Notes Antenna
The antenna configuration as described allows detection of a tag moving at a horizontal line,
through the reading area. The tag orientation is non-critical. The tags are detected along a
horizontal axis of motion in certain regions within the antenna.
The reading area of the antenna is shown in the sketches below.
Ceiling mounted

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 19 of 48
M71110-0e-ID-B.doc
Ceiling mounted
Wall mounted
Fig. 4: Capture area of the antenna
Notes: Note that the entire reading area of the antenna is larger than the three-
dimensional area shown in the drawing (Fig. 4). This means tags can be detected outside
the reading area.
To get an optimal performance the reader has to be configured and run in one of the
Automatic Modes (Buffered Read or Notification Mode).

Identification
Installation
ID ISC.ANT.U500/270–DM
FEIG ELECTRONIC GmbH
Page 20 of 48
M71110-0e-ID-B.doc
To achieve three-dimensional reading of the tag in the reading area drawn above (Fig. 4), the
following conditions must be fulfilled:
-Use of modern sensitive tags
-Tag length not below 9cm
-The antenna should be at least 50 cm away from any metal parts and more than 1m for larger
metal parts
Supplementary equipment (e.g. light barrier, lighting, etc.) or cables, mounted directly on the
antenna or in the immediate vicinity of the antenna can interference with the functioning of the
system. A minimum distance of 20 cm is required.
Metal walls and metal doors should be a few meters away from the antenna.