Feig Electronic OBID i-scan ID ISC.M02 User manual

INSTALLATION MANUAL
final – public (B)
2016-03-17 – M20301-4e-ID-B.doc
ID ISC.M02
(English)

OBID
i-scan
®
HF
Installation
ID ISC.M02
FEIG ELECTRONIC GmbH Page 2 of 27 M20301-4e-ID-B.doc
Note
Copyright 2002 – 2016 by
FEIG ELECTRONIC GmbH
Lange Strasse 4
D-35781 Weilburg-Waldhausen
Tel.: [phone]
http://www.feig.de
With the edition of this document, all previous editions become void. Indications made in this manual may be
changed without previous notice.
Copying of this document, and giving it to others and the use or communication of the contents thereof are
forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved
in the event of the grant of a patent or the registration of a utility model or design.
Composition of the information in this document has been done to the best of our knowledge. FEIG
ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this
manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,
despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.
The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC
GmbH does not give any guarantee promise for perfect function in cross environments and does not give
any guaranty for the functionality of the complete system which incorporates the subject of this document.
FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed
with components and testing methods for a level of reliability suitable for use in or in connection with surgical
implants or as critical components in any life support systems whose failure to perform can reasonably be
expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application
designer must take reasonably prudent steps to protect against system failures.
FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this docu-
ment and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does
not convey any license under its patent rights nor the rights of others.
OBID®and OBID i-scan®is a registered trademark of FEIG ELECTRONIC GmbH.
All brand names, trademarks or logos are property of their respective owners.

OBID
i-scan
®
HF
Installation
ID ISC.M02
FEIG ELECTRONIC GmbH Page 3 of 27 M20301-4e-ID-B.doc
Content
ID ISC.M02 1
1Safety Instructions / Warning - Read before start-up ! 5
2Performance Characteristics of the ID ISC.M02 Reader Module 6
2.1 Performance Characteristics.................................................................................6
2.2 Available module and antenna types....................................................................7
2.3 Scope of delivery ...................................................................................................7
2.4 Optional available ..................................................................................................7
3Installation and wiring 8
3.1 Dimensions.............................................................................................................8
3.2 Wiring......................................................................................................................9
3.2.1 Supply voltage........................................................................................................10
3.2.2 RS232 interface (TTL)............................................................................................11
3.2.3 Data/Clock interface...............................................................................................12
3.2.4 Optional Security Module ID SAM.M02 ..................................................................13
3.3 Display elements..................................................................................................14
3.4 Operating elements..............................................................................................15
3.4.1 Operating/Programming Mode: Jumper J1.............................................................15
3.4.2 Internal/External antenna: Terminal X2, Jumpers J2 and J3...................................16
3.4.3 Retuning the internal antenna: Trim capacitor C65.................................................17
3.5 Installation notes..................................................................................................19
3.5.1 Metallic surroundings .............................................................................................19
3.5.2 EMC effects on cables ...........................................................................................19
3.5.3 EMC effects from magnetic fields...........................................................................20
4Radio Approvals 21
4.1 Europe (CE) ..........................................................................................................21
4.2 Declaration of Conformity ...................................................................................22
4.3 USA (FCC) and Canada (IC).................................................................................23
4.3.1 USA (FCC) approved antennas..............................................................................24

OBID
i-scan
®
HF
Installation
ID ISC.M02
FEIG ELECTRONIC GmbH Page 4 of 27 M20301-4e-ID-B.doc
4.3.2 Canada (IC) approved antennas............................................................................24
4.4 Label Information Reader ID ISC.M02-B.............................................................25
5Technical Data 26

OBID
i-scan
®
HF
Installation
ID ISC.M02
FEIG ELECTRONIC GmbH Page 5 of 27 M20301-4e-ID-B.doc
1 Safety Instructions / Warning - Read before start-up !
•The device may only be used for the purpose intended by the manufacturer.
•The operation manual should be kept readily available at all times for each user.
•Unauthorized changes and the use of spare parts and additional devices which have not been
sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such
unauthorized measures shall exclude the manufacturer from any liability.
•The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid
for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors,
or omissions in the manual or automatically set parameters for a device or for an incorrect
application of a device.
•Repairs may only be undertaken by the manufacturer.
•Installation, operation, and maintenance procedures should only be carried out by qualified
personnel.
•Use of the device and its installation must be in accordance with national legal requirements
and local electrical codes .
•When working on devices the valid safety regulations must be observed.
•Before touching the device, the power supply must always be interrupted. Make sure that the
device is without voltage by measuring. The fading of an operation control (LED) is no indicator
for an interrupted power supply or the device being out of voltage!
•Special advice for wearers of cardiac pacemakers:
Although this device doesn't exceed the valid limits for electromagnetic fields you should keep
a minimum distance of 25 cm between the device and your cardiac pacemaker and not stay in
the immediate proximity of the device’s antenna for any length of time.

OBID
i-scan
®
HF
Installation
ID ISC.M02
FEIG ELECTRONIC GmbH Page 6 of 27 M20301-4e-ID-B.doc
2 Performance Characteristics of the ID ISC.M02 Reader Module
2.1 Performance Characteristics
The ID ISC.M02 Reader Module is designed for reading and writing passive transponders, so-
called “Smart Labels”, with an operating frequency of 13.56 MHz. It is suitable for any application in
which short read ranges and small reader dimensions are required.
The module has an integrated antenna which eliminates the need for additional external antenna
components.
Depending on the requirements, an external 50Ωantenna may also be optionally connected.

OBID
i-scan
®
HF
Installation
ID ISC.M02
FEIG ELECTRONIC GmbH Page 7 of 27 M20301-4e-ID-B.doc
2.2 Available module and antenna types
The following module types are currently available:
Module type Description
ID ISC.M02-B Reader Module with integrated antenna, RS232-TTL and data/clock
interface, for a supply voltage of 5 V DC
The following antenna types are currently available:
Antenna Description
ID ISC.ANT100/100-A PCB-Antenna, 50Ω, 100mm x 100mm (3,94inch x 3,94inch)
ID ISC.ANT40/30-A PCB-Antenna, 50Ω, 40mm x 30mm (1,57inch x 1,57inch)
2.3 Scope of delivery
The following components are included:
Module type Included
ID ISC.M02-B 1 x Reader Module ID ISC.M02-B
2.4 Optional available
The following components are optional available. This parts are necessary if the reader ID
ISC.M02 should be connect to a PC COM-Port.
Module type Order number
ID CAB.A-A Cable for Adaption 2259.000.00.00
ID CAB.RS-A Cable for RS232/485 and Power supply 1690.000.00.00
RS232-TTL Converter 1962.000.00
ID Net.5V 1689.000.00
ID ISC.ANT100/100-A HF Antenna 1968.000.00
ID ISC.ANT40/30-A HF Antenna 1967.000.00

OBID
i-scan
®
HF
Installation
ID ISC.M02
FEIG ELECTRONIC GmbH Page 8 of 27 M20301-4e-ID-B.doc
3 Installation and wiring
3.1 Dimensions
Fig. 1 shows the dimensions of the ID ISC.M02 Reader Module in mm.
Fig. 1: Dimensions of the ID ISC.M02 Reader Module in mm
26,1
2,1
Ø3,3
Ø3,3
Ø3,3
Ø3,3
14,0
11,5
J2
J3
X2
X3
X4
44,0
24,0
3,5
X1
J1
V2
V1
C65
44,0
50,0
C73

OBID
i-scan
®
HF
Installation
ID ISC.M02
FEIG ELECTRONIC GmbH Page 9 of 27 M20301-4e-ID-B.doc
3.2 Wiring
Fig. 2 and Table 1 show the pin assignments for Terminal X1. The pin connector is designed for
flat cable connection using an IDC multipoint socket connector with 2.54 mm pin spacing.
Fig. 2: Pin assignments for Terminal X1
X1
Pin no. Function Description
ID ISC.M02-B
1 DAT Data line for the data/clock interface
2 CLK Clock line for the data/clock interface
3 TxD RS232-TTL – Transmit Data
4 GND ** GND
5 RxD RS232-TTL – Receive Data
6 --- not connected
7 CLS CLS line for the data/clock interface
8 VCC + 5 V DC *
9 GND ** GND
10 --- not connected
* Use only regulated DC power supplies !
** GND-Pins 4 and 9 are to be connected directly to each other
on the Reader Module
Table 1: Pin assignments for Terminal X1
X1
J1
V2V1
C65
X1
12
4 3
5
7
9
6
8
10
J2
J3
X2
X3
X4
C73

OBID
i-scan
®
HF
Installation
ID ISC.M02
FEIG ELECTRONIC GmbH Page 10 of 27 M20301-4e-ID-B.doc
3.2.1 Supply voltage
The reader has to supplied by a limited power supply (e.g. NEC Class 2/LPS power supply) ac-
cording IEC EN 60950, only.
The ID ISC.M02-B must be supplied only by a regulated power supply.
If switching power supplies are used with the module, be sure that there is adequate filtering.
Noise from the power supply can result in a reduction of the read/write range of the module.
The cable length from the power supply should be as short as possible, and should in any case not
exceed 3 m.
X1
Pin no. Function Description
ID ISC.M02-B
8 VCC * + 5 V DC ±5%
9, 4 GND ** GND
* Use only regulated power supplies !
** GND-
Pins 4 and 9 are to be connected directly to each
other on the Reader Module
Table 2: Pin assignments for X1
NOTE:
•Reversing the polarity of the supply voltage may destroy the device.
•Supply voltages outside the specifications may destroy the device.