Fermax DUOX iLOFT Assembly instructions

iLoft Duox Telephone
INSTALLATION AND PROGRAMMING MANUAL
INSTALLATION AND PROGRAMMING MANUAL

Page 2
Cod. 970113I V10_18
Technical publication of an informative nature published by FERMAX ELECTRONICA.
As part of its constant improvement policy, FERMAX ELECTRONICA reserves the right to
modify the content of this document and the characteristics of the products referred to in it at
any time and without prior notice.
Any modification will be reflected in subsequent editions of this document.
CONGRATULATIONS ON PURCHASING THIS QUALITY PRODUCT!
Fermax Electronica manufactures and develops top class equipment which fulfil the highest
design and technology standards.
Your FERMAX telephone will allow you to communicate with the entry panel and open the
front door if you wish.
We hope you enjoy its range of functions.
www.fermax.com.
This product is protected with the following patents and utility models:
PATENTS: US 9215410, US 9762852, BE1023440, AU2014203706.
UTILITY MODELS: ES1187384U, ES1141495U, FR3038192, DE202016000632U1,
CN205987229(U).

Page 3
INDEX
iLOFT DUOX TELEPHONE 4
Installation 4
Connections 5
Diagrams 5
Description 7
- Buttons 7
- Leds 8
Available Functions 9
Capacities 9
Technical Characteristics 10
Programming the telephone 10
- a) From the Panel 11
- b) From the doorbell 12
Telephone set tings 13
- Selecting ringtones 13
*From Panel 13
*From Guard Unit 13
- Simplex conversation mode (Push to Talk) 14
- Call Volume Controller 15
Resetting Parameters 16
Operating 17
* Answering a call 17
·Activating audio 17
·Hanging up 17
·Auto-start 17
*Opening the door 19
·In conversation 19
·Upon receiving a call 19
* Audio volume controller cancelling ringtone 19
* Call to Guard Unit 19
F1 (Additional Functions) 20

Page 4
TELEPHONE installation
1.60m
5.25 feet
(*)
(*)
1 2 3 4

Page 5
CONNECTIONS:
Connection Terminals:
B, B : DUOX Bus: Power, data and audio.
T, -: Connection House entrance "door bell." (P1).
A, -: Call extension connection or light and bell activator
F1: Button for additional functions. It provides a negative upon being activated.
JP1: Line adaptation bridge:
• Right: Without line adaptation.
• Centre: Type C adaptation.
• Left: Type A adaptation.
DIAGRAMS
Wiring: 2 non-polarised wires.
T
+A
-F1
B
in
B
in
B
out
B
out
T
+A
-F1
B
in
B
in
B
out
B
out
T
+A
-F1
B
in
B
in
B
out
B
out

Page 6
T
+ A
-F1
B
in
B
in
B
out
B
out
P1
Call extension
P1 (T, -):You can place an external button to make a call to the "Door bell" (this bell would
replace the ding-dong of the home entrance).
Notes:
- The doorbell can not be changed and is different from those selected for entry panels or
guard unit.
- The do not disturb function silences this tone.
- You can program the phone’s address with this button. See chapter: Programming the
phones address via the doorbell.
A, -: The phone has these terminals, to which you can connect a call extender ref. 2040
oralightand doorbellactivator ref.2438, whichare activatedwhen acall isreceived
or from a outdoor panel, guard unit or from the home’s frontdoor.
Note: If the call disconnection (do not disturb mode), is activated, the terminal will continue
working. Through this, the same tone sounds as that configured for the call answering tone
from the panel, guard unit or doorbell.
-A+A
Red
F1 2A
2A.
Ma . 2A
+A -A
110-240Vac
50-60Hz
REF. 2438
ADS LIGHT COMMANDER
ACTIVADOR DE LUCES ADS
110-240Vac 110-240Vac
T
+ A
-F1
B
in
B
in
B
out
B
out

Page 7
iLOFT DUOX TELEPHONE DESCRIPTION
Buttons
Audio activation, hang up and auto-start button.
On receiving a call the user has 30 seconds to answer. (The red led flashes during
this time to indicate a pending call).
· Audio activation: When a call is received, press this button to speak to the visitor.
The audio channel is opened from the panel entrance to residence, (the blue led
lights up indicating a conversation with the panel entrance, and everything said
will be heard by it).
·Hang-Up: Pressto terminatecommunication. (Whenfinished theblue ledlight again
turns off and the red light is turned on).
The conversation is limited to 90".
The conversation is private, no other terminal can hear it.
· Auto-start (panel 0 in the same block): In standby, press and release this button
(the blue led lights up). If the panel or channel is busy, you will hear a busy tone
and return to standby.
Auto-start: Only with video outdoor panel.
Door open / guard unit call button (function available depending on type of instal-
lation).
· While in conversation with the Outdoor Panel (audio activated), pressing it will
activate the open door lock-release.
· Upon receiving a call (audio not activated). If the phone is not answered you have
30 seconds to open the door.
· When you press this button with the telephone hung-up (standby) a call will be
made to the guard unit (where one exists).
Notes:
- "Hands free" mode is default mode.
- While the audio channel is open the input audio can be regulated with the potentiometer, without affect-
ing the call volume. The selected setting will not be altered if the call volume is subsequently adjusted.
Leds
Micro
1
2
3
4
1Red LED
2Green LED
3Blue LED
4Buttons
Potentiometer

Page 8
Leds
- If the telephone is configured in “simplex mode”, (press to speak and release to listen), the audio chan-
nel will be activated to hear sound at street level.
- If making a call from the 0 panel to another home, during the 30 second wait for the home to answer,
auto-start with the 0 panel will not be possible. If the line is busy or there is another busy telephone in
the same home either.
- During the conversation “hands free” can be adjusted to “simplex mode”.
- If there are various telephones in the same home, the audio will only come from the first one picked-up,
leaving the remaining phones in standby.
Auxiliary F1 function.
F1 configured as exit:
· It is initially configured, by default, as an exit and sends a negative.
Note:
- From the telephone you can activate an auxiliary relay connected to a F1 terminal for an extra function
such as the landing light, alarm activation, etc.
- When you press the F1 button the telephone generates a beep and via the bus transmits a command
to activate a Duox relay (if installed). Simultaneously the F1 terminal provides a negative, as the but-
ton is pressed.
Red LED:
On. Programmed telephone (standby)
RAPID blinking. Telephone not programmed (standby).
SLOW blinking. Indicates that the do not disturb function is activated.
Blue Led:
On. Conversation in hands free audio model.
On/Blinking. Conversation in simplex audio mode
Green LED: According to configuration.
LED FUNCTIONS BLUE led GREEN led RED led
Not programmed
Standby
Call/Called
Handsfree audio
Output Audio (simplex mode)
Input Audio (simplex mode)
Do not Disturb
Doormatic (depending on configuration)

Page 9
AVAILABLE FUNCTIONS
The functions available on the telephone are summarised in the following list:
·Guard Unit Call
·Opening the door
·Call to Guard Unit.
·Ringtone selection.
·Programming from panel and door bell
·Audio connection upon picking up
·Volume regulation
·Auxiliary F1 function.
·Doorbell
·Light and Doorbell Activation
·Hands free audio mode / "simplex (Push to talk)"
·DOORMATIC (depending on configuration)
CAPACITIES
·Numberofterminals perhome: maximum3. Properlysizeconsumptionofthe powersource.
· Number of terminal addresses per sub-block: 99.
· Number of terminal addresses per block: 9999.
·Number of blocks: 99.
·Address for each telephone: 6 decimal digits: 000000. 999999. The address 000000 is the
default address and the telephone does not work.
·Number of conversation channels: 2 per BUS (If there is only audio amplifiers in the instal-
lation).
·Wiring: 2 non-polarised wires, depending on the wire, distances and terminal charges are
stipulated.
·Number of different optional ringtones: 5.
· Call Volume Regulation.
· Input and output audio volume regulation.
· Maximum conversation time. 90 seconds
· Maximum time to pick up on receiving the call: 30 seconds
· Maximum time to programme the telephone: 2.5 minutes.

Page 10
PROGRAMMING THE iLOFT DUOX TELEPHONE
Notes:
- The telephone will not function until it has been programmed.
-You can see that the telephone does not have a programmed address because the led blinks. Once
the telephone’s address is programmed it is indicated via a fixed red light.
- Programming is always done from the panel activated as the master panel. Configuring as master
panel Press the SW1 button 3 consecutive times quickly. After 2 seconds, a confirmation tone is
heard,andthemaster panelisactivated.Oncehavingcompletedthemonitor’sprogramming,deacti-
vatetheMASTERpanelby pressing the SW1 button 3 consecutive times. You can also configure
it via a code on the keypad.For more information see the DUOX Panel Settings at www.fermax.es.
- The programming from the Doorbell is only available if the telephone has not been previously
programmed, that is, if no address is recorded.
- If there is a guard unit, it must be in night mode.
There are two options to program the phone:
a) From the Panel.
b) From the Doorbell.
TECHNICAL FEATURES
Call Ring tone Selection
Operating Temperature
Power supply (non-polarised)
Consumption (±5%)
in standby + led
maximum
IP: 30 / IK: 04
Maximum number of terminals per residence
Telephone address: 6 decimal digits
Number of conversation channels: 2 per BUS
-5º, +40ºC
3
000001...999999
18 Vdc
18 mA
210 mA
Telephone Dimensions (Height x Width x Depth*.):
146 x 90 x 20 mm
Notes:
-this telephone can beinstalleddirectly at surface level,
to the wall or in a standard flush mounted box.
- XX : standard box.
146mm
90mm 20mm