Festo NEBM-M12G8-E S1G15 Series Assembly instructions

Translation of the original instructions
1 Applicable documents
All available documents for the product èwww.festo.com/pk.
2 Safety
2.1 Safety instructions
– Do not connect or disconnect plug connector when powered.
– Only assemble the product on components that are in a condition to be safely
operated.
2.2 Intended use
Connection of motor EMME-AS to motor controller CMMP-AS at connection X2B.
3 Configuration
3.1 Product design
1Socket M12, 8-pin, A-coded (1x)
2Plug Sub-D, 15-pin (1x)
3Cable (1x)
4Screw-type lock
5Screw (2x)
Fig. 1
6Filter (1x)
CAMF-C5-FC
7Screw (4x)
Fig. 2
The filter6 is only required for cable lengths of ³10m.
3.2 Contact assignment
Electrical connec
tion1
Field device side
Pin Signal Pin Electrical connec
tion2
Controller side
1 GND 3
2 Us 10
3 Data+ 12
4 Data– 5
5 +SIN 15
6 REFSIN 8
7 +COS 14
8 REFCOS 7
Tab. 1 Contact assignment
4 Mounting
4.1 Mounting of electrical connection1
Fig. 3
1. Align socket1 with the pins of the plug(A).
2. Lay out encoder cable3 so it is not twisted.
3. Connect socket1 to the plug(A).
4. Tighten screw-type lock4. Tightening torque: 0.4Nm±20%
ÄScrew-type lock4 is at distancex (approx.5.6mm) from the plug con-
nector(B).
Fig. 4
4.2 Mounting of electrical connection2
With cable lengths <10m
1. Align the plug2 to match the socket.
2. Insert the plug2 into the socket.
3. Tighten5 screws. Tightening torque: 0.1Nm±20%
With cable lengths ³10m
1. Align the plug2 to match the socket.
2. Insert the plug2 into the socket.
3. Mount filter6 between the controller (Anschluss X2B) and the plug2.
4. Tighten5 screws. Tightening torque: 0.1Nm±20%
5. Tighten7 screws. Tightening torque: 0.1Nm±20%
4.3 Mounting in energy chain
1. Lay the chain out lengthwise.
2. Place the cables in the chain, making sure they are not twisted.
3. Separate cables from each other using separators/drill holes.
4. Do not connect cables together.
Fig. 5
5. Maintain spaceX. X>10% of the cable diameterD.
If the chain is suspended vertically: increase the spaceX.
Fig. 6
6. Align chain in the operating position:
– Make sure that the radius is greater than the bending radius R of the
cables.
– Cables can move freely in the bending radiusKR of the energy chain.
ÄCables are not forced through the chain.
7. Mount the energy chain ècorresponding instructions.
8. Fasten cables:
– At both ends of the chain in case of short energy chains
– Only at the driver end in the case of long, sliding energy chains
8107328
NEBMM12G8E...S1G15
Encoder cable
8107328
2019-05b
[8107330]
Instructions|Assembly
Festo AG & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
[phone]
www.festo.com

Fig. 7
9. Do not bend cables all the way to the fastening point.
ÄMounting spaceA between the fastening point and bending movement is
observed.
NOTICE!
Damage to cables if the chain breaks.
• Replace cables after a chain break.
NOTICE!
Malfunction and material damage due to vertically suspended cables.
The cables stretch.
• Regularly check the length of the cables.
• Readjust the cables if required.
5 Technical data
NEBMM12G8E...S1G15
Cable characteristic Suitable for energy chains
Cable composition [mm²] 4 x 2 x 0.14
Shielding Shielded
Cable diameter D [mm] 6.8
Mounting space A [mm] 136
Operating voltage range AC/DC UB[V] 0…30
Bending radius
Fixed cable installation R [mm] ³34
Flexible cable installation R [mm] ³68
Ambient temperature
Fixed cable installation [°C] –40…+80
Flexible cable installation [°C] –5…+80
Material
Cable sheath TPE-U(PUR)
Electrical connection1
Function Field device side
Connection type Socket
Connection technology M12x1 A-coded to EN61076-2-101
Type of mounting Screw-type lock
Degree of protection IP65In assembled state
Electrical connection2
Function Controller side
Connection type Plug connector
Connection technology Sub-D
Degree of protection IP30In assembled state
Tab. 2 Technical data