Festo CPX-AP-I-4IOL-M12 User manual

CPX-AP-I-4IOL-M12
IO-Link master
Operating instruc-
tions
8166341
2022-03a
[8166343]

Translation of the original instructions
IO-Link® is a registered trademark of its respective trademark holder in certain countries.

Festo — CPX-AP-I-4IOL-M12 — 2022-03a
3
Table of contents
1 About this document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Applicable documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Product version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Product labelling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Specified standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3 Training of qualified personnel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.4 UL certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Product overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.1 Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.2 Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2.1 Product design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2.2 LED displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.2.3 Connecting elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7 Commissioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7.1 Address space (data length inputs/outputs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.2 IO-Link Device description file (IO-Link Device Description). . . . . . . . . . . . . . . . . . . . . . . 12
8 Parameterisation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9Diagnostics and fault clearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9.1 Diagnostic messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9.2 LED displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
9.3 Event codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9.3.1 Master event codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9.3.2 Device event codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4
Festo — CPX-AP-I-4IOL-M12 — 2022-03a
About this document
1 About this document
1.1 Applicable documents
All available documents for the product è www.festo.com/sp.
Document Contents
Operating instructions for automation system
CPX-AP-I
Instruction manual and important information on
assembly, electrical installation and maintenance
tasks as well as description of the automation
system CPX-AP-I
Tab. 1: Applicable documents
1.2 Product version
This document refers to the following product versions:
Product Version
CPX-AP-I-4IOL-M12 IO-Link Master CPX-AP-I-4IOL-M12 revision 1 or later
Tab. 2: Product version
The product version can be determined from the product labelling.
There may be an updated version of this document for this or later product versions
è www.festo.com/sp.
1.3 Product labelling
The product labelling is located on the right-hand side of the module. The Data Matrix code is on
the connection side. Scanning the printed Data Matrix Code with an appropriate device opens the
Festo Support Portal with the information appropriate for the product. Alternatively, the Product Key
(11-digit alphanumeric code on the product labelling) can be entered in the search field of the Support
Portal è www.festo.com/sp.
1.4 Specified standards
Version
IEC 60204-1:2016-10 EN 60529:1991-10
EN 60204-1:2018-09 –
Tab. 3: Standards specified in the document

Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Product overview
5
2 Safety
2.1 Safety instructions
–Take the legal regulations for the installation location into account.
–Operate the product only within the defined values è 10 Technical data.
–Observe the identifications on the product.
–Observe further applicable documents.
–Store the product in a dry environment protected from UV and corrosion
–If there is a connection to other circuits at one of the connections for inputs or outputs, the circuits
must also comply with SELV/PELV.
–Before working on the product:
Switch off the power supply and secure it against being switched on again.
2.2 Intended use
The product described in this document is intended only for use as an interface between an automa-
tion system CPX-AP and devices with IO-Link Port.
Use the product only as follows:
–Use only in an industrial environment. Outside industrial environments, e.g. in commercial and
residential/mixed-use areas, it may be necessary to take measures to suppress radio interference.
–Use only in combination with modules and components that are approved for the applicable
product variant è www.festo.com/catalogue.
–Only use the product if it is in perfect technical condition.
2.3 Training of qualified personnel
Work on the product should only be conducted by qualified personnel. The qualified personnel must
be familiar with installation of electrical control systems.
2.4 UL certification
The information in the operating instructions for the automation system CPX-AP-I in combination with
the UL inspection mark on the product is also applicable to ensure compliance with the certification
conditions of Underwriters Laboratories Inc. (UL) for USA and Canada è 1.1 Applicable documents.
3 Additional information
–Contact the regional Festo contact if you have technical problems è www.festo.com.
–Accessories è www.festo.com/catalogue.
4Product overview
4.1 Function
The module provides four IO-Link Ports Class B (type B) for connecting IO-LinkDevicesto an automa-
tion system CPX-AP.
The module behaviour can be parameterised è 8 Parameterisation.
Status and error messages are indicated by LED displays on the module and reported to the interface
via system communication.

6
Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Product overview
4.2 Structure
4.2.1 Product design
1
2
3
4
5
6
7
8
9
10
11
12
13
Fig. 1: Product design
1
Mounting interface connection side top
2
IO-Link port 0 [X0] connection
3
IO-Link port 1 [X1] connection
4
IO-Link port 2 [X2] connection
5
IO-Link port 3 [X3] connection
6
Connection for system communication trans-
mission [XF20]
7
Connection for system communication
[XF10]
8
Connection for voltage forwarding [XD2]
9
Connection for power supply [XD1]
10
Mounting interface connection side bottom
and functional earth FE connection
11
Mounting interface, lateral bottom and con-
nection for functional earth FE
12
Inscription label (optional)
13
Mounting interface, lateral top

Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Product overview
7
4.2.2 LED displays
1
2
3
4
5
6
Fig. 2: LED displays
1
Module diagnostics [MD] (green, red)
2
Status/diagnostics of IO-Link port 3 [X3.3]
(green, red, yellow)
3
Status/diagnostics of IO-Link port 2 [X2.2]
(green, red, yellow)
4
Status/diagnostics of IO-Link port 1 [X1.1]
(green, red, yellow)
5
Status/diagnostics of IO-Link port 0 [X0.0]
(green, red, yellow)
6
Status/diagnostics for load supply [PL]
(green, red)

8
Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Product overview
4.2.3 Connecting elements
Connection for power supply [XD1]
M8 plug, 4-pin, A-coded Signal
1 +24 V DC logic supply PS
2 0 V DC load supply PL
3 0 V DC logic supply PS
4 +24 V DC load supply PL
Tab. 4: Connection for power supply
Observe the information on the power supply, see the operating instructions for the automation
system CPX-AP-I è 1.1 Applicable documents.
Connection for voltage forwarding [XD2]
M8 socket, 4-pin, A-coded Signal
1 +24 V DC logic supply PS
2 0 V DC load supply PL
3 0 V DC logic supply PS
4 +24 V DC load supply PL
Tab. 5: Connection for voltage forwarding
Connection for system communication [XF10]
Socket M8, 4-pin, D-coded Signal
1 TX– Transmitted data –
2 RX+ Received data +
3 TX+ Transmitted data +
4 RX– Received data –
Tab. 6: Connection for system communication

Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Commissioning
9
Connection for system communication [XF20]
Socket M8, 4-pin, D-coded Signal
1 RX– Received data –
2 TX+ Transmitted data +
3 RX+ Received data +
4 TX– Transmitted data –
Tab. 7: Connection for system communication
IO-Link Ports [X0] … [X3] connection
M12 socket, 5-pin, A-coded Signal
1 L+ +24 V DC operating voltage supply PS
2 P24 +24 V DC load voltage supply PL
3 L– 0 V DC operating voltage supply PS
4 C/Q Standard IO (in SIO mode) or IO-Link communication (in
IOL mode)
5 N24 0 V DC load voltage supply PL
Tab. 8: IO-Link connection Ports
If there is a connection to other circuits at one of the connections for inputs or outputs, the circuits
must also comply with SELV/PELV.
5Assembly
• Carry out assembly according to the automation system CPX-AP-I operating instructions è 1.1
Applicable documents.
6Installation
• Carry out installation according to the automation system CPX-AP-I operating instructions è 1.1
Applicable documents.
•When connecting Devices Class A with 4 or 5-pin cables, do not connect pins 2 and 5.
7 Commissioning
•Commission the automation system CPX-AP-I in accordance with the operating instructions for the
automation system CPX-AP-I è 1.1 Applicable documents.

10
Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Commissioning
Response of the display components of the module after error-free commissioning
[MD] [PL]
green light green light
Tab. 9: Response of the LED displays of the module after error-free commissioning
Information on troubleshooting in the event of incorrect behaviour:
è Instruction manual for automation system CPX-AP-I è 1.1 Applicable documents
è 9 Diagnostics and fault clearance

Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Commissioning
11
7.1 Address space (data length inputs/outputs)
The address space (data length inputs/outputs) provided by the module can be set using software.
The following variants for setting the address space (data length inputs/outputs) are possible:
Variant Module code
(hex/dec)
Supported net-
work1)
Module [byte] per port [byte]
Inputs2) Outputs Inputs Outputs
2 0x200E/8206 PB, EP, EC 12 8 2 2
2_OE 0x200F/8207 PN, EP 123)
4 0x2010/8208 PB, EP, EC 20 16 4 4
4_OE 0x2011/8209 PN, EP 203)
84) 0x2009/8201 PB, EP, EC 36 32 8 8
8_OE 0x200D/8205 PN, EP 363)
16 0x2012/8210 PB, EP, EC 68 64 16 16
16_OE 0x2013/8211 PN, EP 683)
32 0x2014/8212 EP, EC 132 128 32 32
32_OE 0x2015/8213 PN, EP 1323)
1) PB = PROFIBUS; PN = PROFINET; EP = EtherNet/IP; EC = EtherCAT
2) The last 4 input bytes contain the IO-Link port qualifier information bytes for port 0 … 3.
3) The last 4 output bytes contain the IO-Link OutputEnable bytes for port 0 … 3.
4) Factory setting
Tab. 10: Variants for setting the address space
The "Festo IO-Link Tool" software can be used to set the address space (data length inputs/outputs)
è www.festo.com/sp.
The setting is saved permanently in the module. Changes only become effective after a restart of the
automation system CPX-AP.
OutputEnable Bytes
Bit Contents Description
Bit 0 OutputEnable Traffic jams OutputEnable
–0: output data are invalid
–1: output data are valid
Tab. 11: OutputEnable Bytes
The OutputEnable status is automatically adopted by the PROFINET interface. With the EtherNet/IP
interface, the OutputEnable bit can be set as a validity indicator in the direction of the IO-Link device.

12
Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Parameterisation
Port Qualifier Information Bytes
Bit Contents Description
Bit 7 PQ Port Qualifier: PD status bit copied from IO-Link device in
CKS
–0: input data is invalid
–1: input data is valid
Bit 6 DevErr Device Error:
–1: there is at least one error or warning on the device or
port
–0: there are no errors or warnings on the device or port
Bit 5 DevCom DevCOM:
–1: device is in status PREOPERATE or OPERATE
–0: device is not connected or not yet in operation
Bit 4 Reserved –
Bit 3
Bit 2
Bit 1
Bit 0
Tab. 12: Port Qualifier Information (PQI)
7.2 IO-Link Device description file (IO-Link Device Description)
The "Festo IO-Link Tool" software can be used to configure a IO-Linkdevice è www.festo.com/sp.
Search by part number or type, download in "Software" section.
8 Parameterisation
Various parameters are available for reading out information about the modules in an automation
system CPX-AP and adapting the modules to the application situation.

Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Parameterisation
13
Fieldbus startup parameters
ID Parameter Instances Data type Access1) Arraysize
20022 Configuration of voltage monitoring
load supply PL
–0: load voltage monitoring inactive
–1: load voltage monitoring active,
with suppression of diagnostics at
switch-off (factory setting)
–2: load voltage monitoring active
Only valid for the IO-Link master
module: load voltage diagnostics of
connected IO-Link devices are reported
in all cases.
1 UINT8 rw –
20049 Target cycle time [ms]2)
–0: as fast as possible (factory set-
ting)
–16: 1.6 ms
–32: 3.2 ms
–48: 4.8 ms
–68: 8.0 ms
–73: 10.0 ms
–78: 12.0 ms
–88: 16.0 ms
–98: 20.0 ms
–133: 40.0 ms
–158: 80.0 ms
–183: 120.0 ms
4 UINT8 rw –
20050 Activation of diagnostics for IO-Link
device lost (factory setting TRUE)
4 BOOL rw –
20071 Port mode
–0: DEACTIVATED (factory setting)
–1: IOL_MANUAL
–2: IOL_AUTOSTART
–3: DI_CQ
–97: PREOPERATE3)
4 UINT8 rw –

14
Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Parameterisation
ID Parameter Instances Data type Access1) Arraysize
20072 Review and backup2)
–0: no test (factory setting)
–1: device compatible V1.0
–2: device compatible V1.1
–3: device compatible V1.1
Data storage Backup+ Restore
–4: device compatible V1.1
Data storage Restore
4 UINT8 rw –
20073 Target vendor ID2) 4 UINT16 rw –
20080 Setpoint device ID2) 4 UINT32 rw –
1) ro = read only; rw = read write
2) Changes only become effective when the port mode is changed (ID 20071).
3) Only supported in combination with IO-Link V1.1 devices.
Tab. 13: Fieldbus startup parameters
Fieldbus parameters (status/information)
ID Parameter Instances Data type Access1) Arraysize
20074 Port status information
–0: NO_DEVICE (factory setting)
–1: DEACTIVATED
–2: PORT_DIAG
–3: PREOPERATE
–4: OPERATE
–5: DI_CQ
–6: DO_CQ
–254: PORT_POWER_OFF
–255: NOT_AVAILABLE
4 UINT8 ro –
20075 Revision ID 4 UINT8 ro –
20076 Transmission rate
–0: not detected
–1: COM1
–2: COM2
–3: COM3
4 UINT8 ro –
20077 Actual cycle time [in 100 µs] 4 UINT16 ro –
20078 Actual vendor ID 4 UINT16 ro –
20079 Actual device ID 4 UINT32 ro –

Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Parameterisation
15
ID Parameter Instances Data type Access1) Arraysize
20108 Input data length 4 UINT8 ro –
20109 Output data length 4 UINT8 ro –
1) ro = read only; rw = read write
Tab. 14: Fieldbus parameters (status/information)
AP parameter
ID Parameter Instances Data type Access1) Arraysize
246 Fieldbus serial number 1 UINT32 ro –
791 Product Key 1 CHAR ro 12
960 Firmware Version 1 CHAR ro 30
20000 Module code 1 UINT32 ro –
20085 Measured value of temperature AP-
ASIC [°C]
1 INT16 ro –
20087 Current measured value of logic supply
PS [mV]
1 UINT16 ro –
20088 Current measured value of load supply
PL [mV]
1 UINT16 ro –
20090 IO-Link variant
–8201: variant 8 (factory setting)
–8205: variant 8 OE
–8206: variant 2
–8207: variant 2 OE
–8208: variant 4
–8209: variant 4 OE
–8210: variant 16
–8211: variant 16 OE
–8212: variant 32
–8213: variant 32 OE
1 UINT16 rw –
20093 Hardware version 1 UINT8 ro –
20097 Activation of the operating voltage
supply for all 4 ports
(factory setting TRUE)
1 BOOL rw –
1) ro = read only; rw = read write
Tab. 15: AP parameter

16
Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Diagnostics and fault clearance
9 Diagnostics and fault clearance
9.1 Diagnostic messages
Diagnostic messages of an IO-Link device are sent to the IO-Link Master via event codes. The event
code is mapped in the IO-Link Master to a diagnostics ID è 9.3 Event codes.
For all diagnostic messages of the automation system as well as information on the grouping and
display of the diagnostic messages see the operating instructions for the automation system CPX-AP-I
è 1.1 Applicable documents.
The following table contains the diagnostic messages of the IO-Link master.
ID hex (dec) Message Description
01 | 01 | 010B
(16843019)
Short circuit / Over-
load sensor supply
A short circuit/overload of the sensor supply was detected
Abhilfe –Check the connected sensors for proper
function, especially current consumption.
–Check sensor cable.
Diagno-
sestatus
Error
01 | 01 | 017A
(16843130)
Short circuit at I/Q Short Circuit at I/Q signal (IO-Link)
Remedy –Check wiring
Diag-
nostic
status
Error
01 | 01 | 017B
(16843131)
Short circuit at C/Q (if
digital output)
Short circuit at C/Q (if digital output)
Remedy –
Diag-
nostic
status
Error
01 | 01 | 017C
(16843132)
Overcurrent at I/Q Overcurrent at I/Q
Remedy –
Diag-
nostic
status
Error
01 | 01 | 017D
(16843133)
Overcurrent at C/Q (if
digital output)
Overcurrent at C/Q (if digital output)
Remedy –
Diag-
nostic
status
Error
02 | 01 | 0016
(33619990)
Undervoltage in logic
supply (PS) 24 V DC
Undervoltage in logic supply (PS) 24 V DC
Abhilfe –Check power supply.

Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Diagnostics and fault clearance
17
ID hex (dec) Message Description
02 | 01 | 0016
(33619990)
Undervoltage in logic
supply (PS) 24 V DC
Diagno-
sestatus
Error, Warning
02 | 01 | 0017
(33619991)
Overvoltage in logic
supply (PS) 24 V DC
Overvoltage in logic supply (PS) 24 V DC
Abhilfe –Check power supply.
Diagno-
sestatus
Warning
02 | 01 | 0105
(33620229)
Undervoltage in load
supply (PL) 24 V DC
Undervoltage in load supply (PL) 24 V DC
Abhilfe –Check power supply (load)
–Check for short circuit.
Diagno-
sestatus
Error
02 | 01 | 0106
(33620230)
Load supply (PL) 24 V
DC switched off
Load supply (PL) 24 V DC switched off
Remedy –Check if emergency stop is active
–Check load supply
Diag-
nostic
status
Information
02 | 01 | 013F
(33620287)
Overvoltage in load
supply (PL) 24 V DC
Overvoltage in load supply (PL) 24 V DC
Remedy –Check power supply.
Diag-
nostic
status
Error
06 | 00 | 0109
(100663561)
Startup parameter
rejected by device
The startup parameter specified in the AP device descrip-
tion does not exist in the device or is different from the
specification.
Remedy –Check firmware versions
Diag-
nostic
status
Error
08 | 00 | 0135
(134218037)
Wirefracture detected Wirefracture detected
Remedy –Check wiring
Diag-
nostic
status
Error

18
Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Diagnostics and fault clearance
ID hex (dec) Message Description
08 | 01 | 0130
(134283568)
AP module process
data output watchdog
timed out
The process data watchdog for the outputs timed out in
the module
Remedy –Restart AP master.
–Check wiring.
Diag-
nostic
status
Error
08 | 01 | 0131
(134283569)
AP module process
data input watchdog
timed out
The process data watchdog for the inputs timed out in the
module
Remedy –Restart AP master.
–Check wiring.
Diag-
nostic
status
Error
08 | 01 | 01A2
(134283682)
Device in System
State Emergency
Operation
The system initialization (module recognition) failed. The
system is in maintenance mode. No I/O function is avail-
able.
Remedy –Restart system
–Update firmware to latest version
–Contact Festo service
Diag-
nostic
status
Error
08 | 0A | 0108
(134873352)
IO-Link event An IO-Link event (Notification, Warning or Error) occurred.
IO-Link specific details are attached to this notification.
Remedy –See documentation of IO-Link Master or
Device
Diag-
nostic
status
Information, Warning, Error
08 | 0A | 014C
(134873420)
Invalid cycle time Invalid cycle time of IO-Link communication
Remedy –Adapt cycle time to permissable value
Diag-
nostic
status
Error
08 | 0A | 014D
(134873421)
Revision fault –
incompatible protocol
version
Revision fault – incompatible IO-Link protocol version
Remedy –Device not compatible

Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Diagnostics and fault clearance
19
ID hex (dec) Message Description
08 | 0A | 014D
(134873421)
Revision fault –
incompatible protocol
version
Diag-
nostic
status
Error
08 | 0A | 014E
(134873422)
ISDU batch failed
– parameter inconsis-
tency?
ISDU batch failed – parameter inconsistency?
Remedy –
Diag-
nostic
status
Error
08 | 0A | 016B
(134873451)
Incorrect VendorID –
Inspection Level mis-
match
The detected IO-Link device does not match the config-
ured VendorID
Remedy –Check if correct IO-Link device is connected
Diag-
nostic
status
Error
08 | 0A | 0177
(134873463)
Backup inconsistency
– upload fault
IO-Link Backup/Restore failed. Upload fault
Remedy –
Diag-
nostic
status
Error
08 | 0A | 0178
(134873464)
Parameter inconsis-
tency – download
fault
IO-Link Backup/Restore failed. Download fault
Remedy –
Diag-
nostic
status
Error
08 | 0A | 017F
(134873471)
Process data mis-
match
Reserved process length data for IO-Link device too small
Remedy –Change module variant to a bigger process
data length
Diag-
nostic
status
Error
08 | 0A | 0182
(134873474)
Device Event overflow Too many IO-Link Events. Events might be lost.
Remedy –
Diag-
nostic
status
Error

20
Festo — CPX-AP-I-4IOL-M12 — 2022-03a
Diagnostics and fault clearance
ID hex (dec) Message Description
08 | 0A | 0183
(134873475)
Backup inconsistency
– memory out of
range (2048 octets)
IO-Link Backup/Restore failed. Memory out of range
(2048 octets)
Remedy –Device specific
Diag-
nostic
status
Error
08 | 0A | 0184
(134873476)
Backup inconsistency
– DataStorageIndex
not available
IO-Link Backup/Restore failed. DataStorageIndex not
available
Remedy –Device specific
Diag-
nostic
status
Error
08 | 0A | 0185
(134873477)
Backup inconsistency
– Data Storage unspe-
cific error
IO-Link Backup/Restore failed. Data Storage unspecific
error
Remedy –Device specific
Diag-
nostic
status
Error
08 | 0A | 01A8
(134873512)
Incorrect DeviceID –
Inspection Level mis-
match
The detected IO-Link device does not match the config-
ured DeviceID.
Remedy –Check if correct IO-Link device is connected
Diag-
nostic
status
Error
08 | 0A | 01A9
(134873513)
No Device No Device (communication)
Remedy –Check if IO-Link device is connected
Diag-
nostic
status
Error
Tab. 16: Diagnostic messages