Festo CPX-M-FB20 User manual

Brief description
CPX field bus
node
type CPX-M-FB20
type CPX-M-FB21
– English
8101678
2018-11b
[8101680]
CPX-Terminal

Festo CPX-M-FB20/21-Z6 2018-11b2
Translation of the original instructions
Documentation on the product
For all available product documentation
èwww.festo.com/pk
Copyright:
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
Internet: http://www.festo.com
E-Mail: [e-mail]
Reproduction, distribution or sale of this document or communication of
its contents to others without express authorization is prohibited.
Offenders will be liable for damages. All rights reserved in the event that
a patent, utility model or design patent is registered.
English 3............................................

Festo CPX-M-FB20/21-Z6 2018-11b English 3
English
1 User instructions
The field bus node CPX-M-FB20/21 for CPX terminals is
intended exclusively for use as a slave on the Interbus.
The maximum values specified in “Technical data” must be
observed here. Detailed information can be found in the
manual for the field bus node P.BE-CPX-FB20/21-... as well
as in the CPX system manual P.BE-CPX-SYS-... .
Warning
 Switch off the power supply before mounting or
dismantling modules or connecting or disconnecting
plug connectors (danger of operative malfunctions or
damage).
 Only use power sources which guarantee a secure
electrical isolation of the operating voltage as per
IEC/DIN EN 60204-1. Also observe the general
requirements for PELV power circuits as per
IEC/DIN EN 60204-1.
 Connect an earth conductor of sufficient cable cross
section to the connection on the CPX terminal
marked with the earth symbol.
 The CPX bus node contains electrostatically sensitive
components. Therefore, do not touch any compon
ents. Observe the handling specifications for electro
statically sensitive devices.
Note
Only commission a CPX terminal which has been
mounted and wired completely.

Festo CPX-M-FB20/21-Z6 2018-11b English
4
2 Connection and display components
1Service interface for
handheld, etc.
2DIL switch
(under the cover)
3FB21 only:
Fieldbus connection
OUT (continuing
fibre-optic cable
(FOC))
4Fieldbus connection
IN (incoming FOC)
5Bus-status-specific
and CPX-specific
LEDs
123
4
5

Festo CPX-M-FB20/21-Z6 2018-11b English 5
Bus status LEDs CPX-specific LEDs
UL Interbus diagnostics
(green)
SF System fault (red)
RC Fieldbus connection
(green)
US1 Diagnostics, logic voltage
supply (green)
BA Remote bus active (green) US2 Diagnostics, load voltage
supply (green)
RD Remote bus switched off
(yellow)
MParametrisation modified
or Force active (yellow)
FO1 Diagnostics, incoming fibre
optic cable length (yellow)
FO2 FB21 only:
Diagnostics, continuing
fibre optic cable length
(yellow)
In normal operating status all green LEDs light up; the yellow and red
LEDs do not light up.
Without a field bus connection the LEDs UL, RD, US1 and US2 light up.

Festo CPX-M-FB20/21-Z6 2018-11b English
6
3 Installation instructions
3.1 Replacement of the fieldbus node
Please note
The fieldbus node FB20/21 consists of two CPX-M
interlinking blocks, a sub-base and the two Rugged Line
connections. Removal of these components is not
permitted. The fieldbus node FB20/21 should only be
exchanged completely.
The interlinking blocks in the metal version are each linked
to the adjacent interlinking block or end plate by means of
screws.
1Screws,
tightening torque
3 Nm ± 0.3 Nm
2Fieldbus node
CPX-M-FB20/21
12
1

Festo CPX-M-FB20/21-Z6 2018-11b English 7
Dismantling:
1. Undo the screws from the right interlinking block of
the fieldbus node and the left adjacent component
(e.g. end plate).
Note
Do not bend the electrical plug connectors on the inter
linking blocks.
2. Carefully remove the interlinking block of the fieldbus
node from the adjacent components without tilting it.
Installation:
Note
When interlinking blocks are arranged in series:
Do not bend the electrical plug connectors on the inter
linking blocks.
1. Align the CPX terminal on a flat surface so that the
components are not offset. The bolts attached to the
left-hand side of the interlinking block help you with
the alignment.
2. Push the interlinking blocks together carefully without
tilting them.
3. Screw the connector screws a few rotations into the
adjacent interlinking block.
4. Tighten the screws evenly, hexagon socket size A/F4,
tightening torque 3 Nm ± 0.3 Nm.

Festo CPX-M-FB20/21-Z6 2018-11b English
8
3.2 DIL switch settings
Switch Setting Function 1)
11 = OFF Baud rate 500 kBd
1 = ON Baud rate 2 Mbd 1)
2 --- Reserved 1)
33 = OFF Data format standard 1)
3 = ON Data format Siemens (Byte swap)
44 = OFF Register undervoltage Vload as
peripheral fault 1)
4 = ON Do not register undervoltage Vload
5 / 6 5 = OFF
6 = OFF
(M1) without diagnostics in PAE 1)
5 = OFF
6 = ON
(M2) 4 Byte diagnostics start PAE
5 = ON
6 = OFF
(M3) 2 Byte diagnostics end PAE
5 = ON
6 = ON
(M4) 4 Byte diagnostics end PAE
7 / 8 --- Reserved 1)
1) Factory setting

Festo CPX-M-FB20/21-Z6 2018-11b English 9
3.3 Pin allocation for Rugged Line plug
Bus, fibre optic cable (FOC) Operating voltage
OUT
IN
4
3
25
1
Incoming FOC:
OUT = Transmitted data
Wire colour = black
IN = Received data
Wire colour = orange
Continuing FOC (FB21 only):
OUT = Transmitted data
Wire colour = orange
IN = Received data
Wire colour = black
1 = 24 V supply
Electronics, inputs
2 = 0 V electronics, inputs
3 = 24 V supply
Valves, outputs
4 = 0 V valves, outputs
5 = Functional earth

Festo CPX-M-FB20/21-Z6 2018-11b English
10
Connection Plug type
Bus and power supply connecting
plug (2 items)
IBS RL PLUG-LK/POF
Source of supply: Phoenix Contact Deutschland GmbH, Postfach 1341
D-32825 Blomberg, http://www.phoenixcontact.com
3.4 Power supply of the CPX terminal
The operating and load voltage supply is supplied by
FB20/FB21 of the CPX terminal via the Rugged Line
connection.
Note
Use of the interlinking blocks with system supply type
CPX-M-GE-EV-S-… is not permitted in combination with
the FB20/FB21.
The outputs can either be supplied with load voltage via
the FB20/FB21 or optionally via the additional power
supply for outputs. The additional power supply should
only be installed on the right-hand side of the FB20/21
(see example below).
Plug Pin assignment for additional power
supply
1
2
3
45
Type CPX-M-GE-EV-Z-7/8-5POL
1: 0 VOff
2: unused
3: FE
4: unused
5: 24 VOff
1 2 3 4 5 Type CPX-M-GE-EV-Z-PP-5POL (Push Pull)
1: not connected
2: not connected
3: 24 VOff
4: 0 VOff
5: FE