FingerTec R3 User manual

© 2014 Timetec Computing Sdn Bhd. All rights reserved.• 102014
4 feet / 1.2 meter
(recommended)
DC12V
Power Supply
For NC or NO door lock system
1. RS485 Single Connection
RS232
cable
RS232/RS485
Data Converter
TCP/IP
RJ45-1 RJ45-2 RJ45-3 RJ45-4
3rd party controller
with 26 bits
Wiegand output
BEEP
GLED
RLED
INWD0 INWD1
GND
+12V
BEL+
BEL_
SEN
GND
BUT
NO
COM
NC
ALM_
ALM+
+12V
GND
WD0
WD1
GND
RXD
TXD
GND
485+
485_
3rd party controller
with 26 bits
Wiegand input
485+
485_
RX+
RX_
2. RS485 Network Connection
RS232/RS485
Data Converter
485+
485_
RX+
RX_
485+
485_
Installation Guide
R3
Fingerprint Color Door Access &
Time Attendance
Step 1
Determine the Location and Position
of the Installation
• Avoid installing the terminals in locations that have contact with
a strong light source (e.g direct sunlight, spotlight, fluorescent
light, etc)
• Avoid installing the terminals in locations prone to high moisture
or condensation levels in the air
• The recommended installation height of the terminals from the
ground is 1.2 meter.
Step 2
Mounting Terminals
It is recommended that the terminals be mounted to a wall in
to ease the process of enrolment and verification. In a situation
whereby mounting the terminals on a wall is not an option, you
can choose to use flexi kit to convert the terminals to desktop units.
However, there are limited options for the flexi kit and some termi-
nals might not be suitable to be placed on flexi kits.
A. MOUNT ON WALL
• After measuring the height
accordingly and make rel-
evant marking on the wall,
drill the screws into the wall
to secure the back plate.
• Attach the terminal to the
back plate and tighten the
screws. Refer to Appendix I
for dimensions and meas-
urements of installation.
Step 3
Wiring for Power Supply
The power input ports for this model are located at the rear of the
terminal. There is no adapter plug supplied with the model, you
need to source for power cable (red and black cables) to connect
the power from the terminal to the AdapTec.

RJ45-1 RJ45-2 RJ45-3 RJ45-4
BEEP
GLED
RLED
INWD0 INWD1
GND
+12V
+12V
GND
WD0
WD1
GND
RXD
TXD
GND
485+
485_
DC12V
Power Supply
Doorbell
Door sensor
Release button
Key switch
(NC)
C A
Emergency
break glass
(NC)
3 2
EM lock
(NC)
_+
BEL+
BEL_
SEN
GND
BUT
NO
COM
NC
ALM_
ALM+
RJ45-1 RJ45-2 RJ45-3 RJ45-4
BEEP
GLED
RLED
INWD0 INWD1
GND
+12V
BEL+
BEL_
SEN
GND
BUT
NO
COM
NC
ALM_
ALM+
+12V
GND
WD0
WD1
GND
RXD
TXD
GND
485+
485_
DC12V
Power Supply
Doorbell
Door sensor
Release button
Key switch
(NO)
C A
Emergency
break glass
(NO)
3 2
EM lock
(NO)
_+
Step 4
Setting Up Data Communication
(Skip this step if you are using USB ash disk to transfer data)
The data communication ports are positioned at the rear of the ter-
minals, please refer to the diagrams shown on Step 3 to determine
the wiring. Plug the communication jacks (TCP/IP, RS232 or RS485) to
the corresponding ports.
TCP/IP – LAN Connection
For TCP/IP connection, plug the special RJ45 jack into the TCP/IP
(LAN) Port of the terminal. Connect the other end (normal RJ45 jack)
to the local area network hub or a PC. Configure the device ID, IP
address, subnet mask and Gateway in the terminal (refer to the hard-
ware user manual for details).
RS232 – Serial Port Connection
Plug the communication jack that is provided in the package to con-
nect to the communication port of the terminal. Select wires with
label RX, TX and GND, and connect the other end of these wires to a
DB9 female connector. Configure the device ID and baudrate of the
terminal (refer to the hardware user manual for details). Use the nor-
mal RS232 cable to plug into the RS232 port of the terminal.
RS485 – Serial Port Connection
Plug the communication jack that is provided in the package to con-
nect to the communication port of the terminal. Select wires with
label RS485+, RS485- and GND, and connect the other end of these
wires to an RS232/485 data converter. Connect the other end of the
data converter to a DB9 female connector. Configure the device ID
and baudrate of the terminal (refer to the hardware user manual for
details).
Step 5
Finalizing the Installation
1. Check that all cable connections are done correctly.
2. Attach the terminal to the corresponding back plates and
tighten the screws to secure the terminal on the wall.
3. Switch on the power to the terminal.
4. Start using the terminal.
Appendix
Power Supply & Door Lock System Wiring
Diagram
Diagram1 • Normally Close (NC)
Diagram2 • Normally Open (NO)
Other Accessories
FingerTec offers complementing accessories which can be used with
your terminals. These optional accessories are available at
http://accessory.fingertec.com
AdapTec Plus
The AdapTec Plus is a 12VDC power supply inclusive of a 110~240VAC
switching linear power. The AdapTec supplies 12VDC power to the
FingerTec terminal and door lock system as well as charges a 12VDC
7.0Ah backup battery simultaneously.
During an event of a power failure, the back up battery automatically
provides power to the terminal and maintains the door lock system.
The AdapTec Plus also prevents a secured door from being opened if
it has been tampered with.
Enclosures
An acrylic-made enclosure that protects your terminal from the risk
of meddling by unauthorized individuals. Our custom made enclo-
sure are specially designed to fit your terminal perfectly with specific
openings for fingerprint scanner and buttons. Our enclosure can be
used to mitigate surrounding mild environmental hazards and help
lengthen the lifespan of the terminals. However, do note that the en-
closure is not dust-resistant and waterproof if subjected to extreme
weather conditions.
Door Lock Accessories
FingerTec offers various door locks accessories to complement Fin-
gerTec door access product range.

USAGE
Dry Contact
(independ-ent power supply for door lock)
• NO type door lock (NO-COM)
• NC type door lock (NC-COM)
Power Contact
(using power from terminal to power on door lock)
• NO type door lock (NO-GND)
• NC type door lock (NC-GND)
Dry Contact
(independ-ent power supply for door lock)
• NO type door lock (NO-COM)
• NC type door lock (NC-COM)
Power Contact
(using power from terminal to power on door lock)
• COM1 - +12V
Door Sensor
(SEN-GND)
Release Button
(BUT-GND)
Door Bell
Alarm System
NO or NC Type – Check in
Advance Options
WIRING
PORT
NO
NC
COM
SEN
GND
BUT
Bell+
Bell-
AL+
AL-
Appendix I
Terminal Dimensions and Measurements
Front View of Back Plate
Door Lock Connectors
The terminal will trigger the alarm output (NO or NC) in the following
situations:
• Door forced open (A door sensor must first be installed)
• Door open time out (A door sensor must first be installed)
• Terminal has been illegally dismantled.
78 mm
44mm
62mm
190 mm
44mm 17mm
17mm
17mm17mm