FingerTec TA100C User manual

ENCLOSURE
INSTALLATION
DIAGRAM
1. Position the back plate properly on top
of the mounting plate; tighten the bolts
and nuts to join these two plates
together securely.
2. Position the wall plate that has been
attached to the back plate, and tighten
the screws to secure them on the
enclosure.
3. Mount the enclosure on a wall or a
surface and tighten the screws to secure
its position.
4. Hang the terminal on the back plate,
tighten the 2 screws at the bottom of the
terminal.
5. Make sure that the enclosure has been
mounted firmly by tightening all the
screws.
Note:
Installation of enclosure with access control
Note:
The package does not include the screws
needed to secure the enclosure to a wall
models
Before you start with step no.1 above,make sure
that all the terminal's wires are put through the
enclosure,back plate and wall plate,and all the
wires are connected to the terminal's ports
correctly.
1
2
5
3
4
Terminal
Enclosure
1
1
2
3
5
5
3
3
3
4
Wall plate
Terminal
Enclosure
1
1
2
3
5
5
3
3
3
4
Wall plate
Back plate
3
www.fingertec.comwww.fingertec.com
C2011 FingerTec Worldwide Sdn. Bhd. All rights reserved.
INSTALLATION DIAGRAM • R2
INSTALLATION DIAGRAM •AC900
INSTALLATION DIAGRAM •Kadex
Enclosure
1
3
4
Wall plate
Back plate
Terminal
1
1
2
2
3
3
3
INSTALLATION DIAGRAM •i-Kiosk 100
Terminal
Enclosure
Wall plate
Back plate
4
1
1
13
3
3
3
2
2
Back plate

ENCLOSURE
INSTALLATION
DIAGRAM
1. Position the back plate properly on top
of the mounting plate; tighten the bolts
and nuts to join these two plates
together securely.
2. Position the wall plate that has been
attached to the back plate, and tighten
the screws to secure them on the
enclosure.
3. Mount the enclosure on a wall or a
surface and tighten the screws to secure
its position.
4. Hang the terminal on the back plate,
tighten the 2 screws at the bottom of the
terminal.
5. Make sure that the enclosure has been
mounted firmly by tightening all the
screws.
Note:
Installation of enclosure with access control
models
Before you start with step no.1 above,make sure
that all the terminal's wires are put through the
enclosure,back plate and wall plate,and all the
wires are connected to the terminal's ports
correctly.
1
2
5
3
4
1. Position the screws on the wall plate to
hang AC100C terminal.
2. Place the wall plate on the enclosure;
tighten the screws to secure it on the
enclosure
3. Mount the enclosure on a wall or a surface
and tighten the screws to secure its position
4. Hang the AC100C terminal on the wall plate.
5. Make sure the enclosure has been mounted
firmly on a wall by tightening all the
screws.
INSTALLATION DIAGRAM • i-Kiosk 100 Plus
Terminal
Enclosure
Wall plate
Back plate
4
2
1
1
1
1
3
3
3
3
2
Terminal
Enclosure
Wall plate
Back plate
2
4
1
2
3
3
3
3
1
INSTALLATION DIAGRAM • TA100C Series / TimeLine 100
INSTALLATION DIAGRAM • Q2i / TA200 Plus
Terminal
Enclosure
Wall plate
Back plate
2
4
1
2
3
3
3
3
1
1
1
1
INSTALLATION DIAGRAM • AC100C Series
Terminal
Enclosure
Wall plate
1
2
4
3
1
2
3
3
3
1
2
5
3
4
Note:
The package does not include the screws
needed to secure the enclosure to a wall