FRAME IT ALL Topolski 8' x 8' User manual

800001131, 800001132, 800001133, 800001134
800002131, 800002132, 800002133, 800002134
800003131, 800003132, 800003133, 800003134
800004131, 800004132, 800004133, 800004134
RAISED GARDEN BED
8’ x 8’ Topolski
Layout your Boards along the borderline and connect each
Board together by inserting the top of the stake through the
bracket loops with the stake pointing to the sky. This enables
you to freely position your border to get your desired location.
Customer Service: 1800-914-9835 |
[email protected]m
© Frame It All. All Rights Reserved.
2 LEVEL KIT CONTAINS:
•Composite Boards 4’ x 16
•Composite Boards 2’ x 12
•Stacking Brackets x 48
•4-way Bracing Brackets x 8
•Stacking Stakes x 26
•Plugs x 112
•Caps x 13
ASSEMBLY INSTRUCTIONS –Level 1
STEP 1:
Assemble the Boards by sliding one end of Board into channel end
of one of the brackets. Use plugs to cover the holes on both sides to
lock the bracket in place.
1. Connect 8x 4ft Boards with Stacking Brackets on
both ends in alternating orientation.
2. Connect 5x 2ft Boards in the same pattern
FOR INDOOR & HARD SURFACE:
If you plan to assemble raised bed on a hard surface, use
hacksaw to remove the spike of each stake. Use these cut
down stakes for the base level only of your raised garden.
Trim stake spike with
hacksawfor use indoor
or on hard surfaces
How the Joints Work
Use plugs (included)
to cover the holes on
both side of Boards
Use plugs to
cover the holes
–two plugs are
required per
bracket (1 on
each side)
Use a Capto
complete the
top level.
Use stacking
stakes for
ground level
frames and
stacking
additional levels.
Use stacking
stake when
creating a
multi-level
Stacking stake fit
into the tops other
Stacking stakes
3-Way Connection:
Combine a top 4-way
bracket, mid-section 4-
way bracket and
stackingbracket.
2 LEVELS
3 LEVEL KIT CONTAINS:
•Composite Boards 4’ x 24
•Composite Boards 2’ x 17
•Stacking Brackets x 74
•4-way Bracing Brackets x 8
•Stacking Stakes x 39
•Plugs x 164
•Caps x 13
4 LEVEL KIT CONTAINS:
•Composite Boards 4’ x 32
•Composite Boards 2’ x 24
•Stacking Brackets x 96
•4-way Bracing Brackets x 16
•Stacking Stakes x 52
•Plugs x 224
•Caps x 13
1
2
Recommended Tools:
- Hammer
- Flathead Screwdriver
1 LEVEL KIT CONTAINS:
•Composite Boards 4’ x 8
•Composite Boards 2’ x 5
•Stacking Brackets x 26
•Stacking Stakes x 13
•Plugs x 52
•Caps x 13
1 LEVEL

ASSEMBLY INSTRUCTIONS –Level 1 Continued
1
1
2
Step 2: Layout the Boards for the first level according to the number of the
board in Step 1.
IMPORTANT: If you connect any brackets incorrectly, they can be removed by
inserting a flathead screwdriver into the opening of the snap-lock plugs, pushing into
the nub and twisting upwards.
Step 3: When connecting the boards for the first level, insert the stacking
stakes upside down so the stake is pointing to the sky. This will allow you to
adjust the shape of your frame before driving the stakes into the ground.
Step 3:a With the first level stacking stakes still facing the sky, use a
bracketed 2ft Board to ensure that the cross Boards will fit by placing the
board over the stacking stakes on the cross-board positions shown below.
Step 4: Once you finish with the adjustments of your base level frame,
remove the Boards sitting on level 2 and hammer the stacking stakes on level
1 into the ground.
1
1
1
1
11
22

STEP 5:
Connect the brackets and boards for the second level in the following pattern:
1. Connect 3x 4ft Boards with Stacking Brackets on
both ends in alternating orientation.
2. Connect 1x 4ft Boards with stacking brackets
on both sides, facing the same orientation.
3. Connect 4x 4ft Boards with a stacking bracket on
one end and a mid-section 4-way bracket on the
other end in alternating orientation.
4. Connect 2x 2ft Boards with a stacking bracket on
both ends in alternating orientation.
5. Connect 3x 2ft Boards with stacking brackets on
both sides, facing the same orientation.
6. Connect 2x 2ft Boards with top 4-way brackets
on both ends, in alternating orientation.
ASSEMBLY INSTRUCTIONS –Level 2
1
2
3
4
5
6
1
11
2
6
3
5
6
3
55
33
Step 6: Layout the boards the second level of your design on the ground
around your base frame. Once they are all laid out, begin stacking and
connecting them starting at a corner and working your way out.
NOTE: Stacking stakes will be used for all additional levels and can insert into
the top of existing stakes.
Step 7: For a 3-level design, repeat steps 1 & 2. For the final 4th level,
repeat Step 5 & 6.
Step 8: Once your final level is installed, attack a finishing cap on top of
each joint and then you’re reading to fill with soil!
Happy Gardening!