Frico CIR105 User manual

Comfortinfra
CIR
SE
... 5
... 4
NO
GB
... 8
... 7
... 6
FI ...
... 9
DE
NL ... 10
FR

CIR
2

CIR
3

CIR
7
Area of use
The radiant heaters are primarily used to create
comfortable heating on terraces, balconies,
openair
restaurants etc. They can also be used for
selective heating in storage rooms and workshops.
The Confortinfra is also approved for installation in
bathrooms and shower rooms.
The heater is approved by SEMKO in splash proof
design, IP24. It carries the CE-mark and is in
compliance with the EMC-directive.
Positioning
The heaters must be mounted so that they enclose
the area which is to be heated, see fig. 3. Suitable
distance from the floor is 2—2,5 m. Closer to the
floor is not recommended as the additional heat
may seem unpleasant.
Mounting
• First study fig. 1 and 2. NB! The minimum
distances in fig. 1 must be kept!
• The heaters may only be mounted horizontally!
• The heater must not be mounted so the circuit
breaker can be reached from a bathtub or
shower.
• The heater must not be placed directly under a
wall-outlet!
• The mounting brackets enable mounting in
three different angles for ceiling or wall
mounting. Parallel to the wall/ceiling, 18° or
36° angle.
• Choose the desired angle and fasten the
bracket onto wall or ceiling. The holes are Ø 5
mm, c-c distance is 25 mm.
• Fasten the heaters, snap into the brackets, and
secure it by tightening the securing screws (104
mm long) and the domed nuts (spanner width
7 mm).
Electrical installation
The electrical installation should be perma-nent
and carried out by a qualified electrician in
conformity with prevailing regulations. The CIR
1XX type must be preceded by an all-pole switch. A
terminal block, which enables connection to other
heaters is situated on the same end of the heater
as the name plate.
Please note that the inlet must be tight. A cable of
EKK or EKLK type or similar must be used.
Minimum cross section area
230V
protected by 10A (up to 2 kW) - min. 1,5mm²
protected by 16A (2—3,5 kW) - min. 2,5 mm²
400V
protected by 10A (up to 4kW) - min. 1,5 mm²
protected by 1 6A (4—6 kW) - min. 2,5 mm²
Maintenance
The heater is on the whole made of rustproof
material and usually does not require any
maintenance. Pollution can in the long run dull
the reflectors somewhat. This however has very
little affect on its function.
If the heater is very dirty it can be cleaned with
compressed air. If the reflector remains dirty it must
be replaced by an authorized repairman. The
reflector must not be polished as this may damage
the protective surface.
GB

Declaration of Conformity
We
Frico AB
Box 102
S-433 22 Partille
under own responsibility hereby declare that the following product(s)
Room heaters: Infrared radiators
Type: CIR 105, CIR 110, CIR 115 and CIR 120.
CIR 205, CIR 210, CIR 215 and CIR 220.
which is(are) covered by this declaration of conformity comply with the
EC Electromagnetic Compatibility (EMC) Directive 89/336 /EEC & 92/31 EEC
EC Low Voltage Directive (LVD) 73/23/EEC
and is(are) manufactured in accordance with the following stated harmonised
standard(s) or other normative document(s).
EMC: EN 55 014: 1993
EN 60 555-2/3: 1991
EN 55 104
LVD: EN 60 335-1: 1988 incl. Am. 2, 5, 6, 51-54
EN 60 335-2-30: 1992 incl. Am. 51
Partille , 15 December 1995
Mats Careborg
Technical Manager

Main office
FRICO AB Tel: [phone]
Box 102 Fax: [phone]
S-433 22 Partille e-mail: [email protected]
SWEDEN http://www.frico.se
Norway
FRICO AS
Postboks 82, Alnabru Tel: [phone]
N-0614 Oslo Fax: [phone]
NORWAY e-mail: [email protected]
http://www.frico.no
France
FRICO FRANCE Tel: [phone]
7, rue de la libération Fax: [phone]
F-69 270 Fontaines sur Saone e-mail: [email protected]
FRANCE
Russia
FRICO representative office in Russia
1 st Golutvinsky per., 3 Tel/Fax: [phone]
Moscow 109180 e-mail: [email protected]
RUSSIA
For latetest updated information, see: www.frico.se
Artnr: 201397 01-08-24