FujiFilm SonoSite SII Stand User manual

Stand
User Guide

ii
SonoSite SII, SonoSite, and the SonoSite logo are registered and unregistered trademarks of FUJIFILM SonoSite, Inc. in various
jurisdictions.
All other trademarks are the property of their respective owners.
Part Number: P20557-02
Publication Date: November 2017
Copyright © 2017 FUJIFILM SonoSite, Inc. All Rights reserved.
Manufacturer
FUJIFILM SonoSite, Inc.
21919 30th Drive SE
Bothell, WA 98021 USA
T: 1-888-482-9449 or 1-425-951-1200
F: 1-425-951-1201
EC Authorized Representative
FUJIFILM SonoSite B.V.
Joop Geesinkweg 140
1114 AB Amsterdam,
The Netherlands
Australia Sponsor
FUJIFILM SonoSite Australasia Pty Ltd
114 Old Pittwater Road
BROOKVALE, NSW, 2100
Australia
Caution United States law restricts this device to sale by or on the order of a physician.

English Deutsch Español Français Italiano Português
SonoSite SII Stand User Guide 1
SonoSite SII Stand User Guide
Contents
Introduction ................................................................................................................................... 1
Conventions ................................................................................................................................ 2
Customer assistance and comments ........................................................................................ 2
Stand features ................................................................................................................................ 3
Attaching and removing the ultrasound system ......................................................................... 4
Adjusting the height and angle of the stand ............................................................................... 7
Moving and locking the stand ...................................................................................................... 9
Troubleshooting .......................................................................................................................... 10
Cleaning and disinfecting ........................................................................................................... 11
Safety ............................................................................................................................................ 13
Electrical safety ........................................................................................................................ 13
Equipment safety ..................................................................................................................... 13
Clinical safety ........................................................................................................................... 14
Electromagnetic compatibility (EMC) ..................................................................................... 14
Specifications ............................................................................................................................... 16
Stand dimensions .................................................................................................................... 16
Temperature and humidity limits ........................................................................................... 17
Peripherals ................................................................................................................................ 17
Introduction
The SonoSite SII Stand User Guide explains how to use the SonoSite SII stand and peripherals. For information
on a peripheral, see the manufacturer’s instructions included with that product. For information on the
transducers, see the SonoSite SII Ultrasound System User Guide.
If you need to disassemble the stand, refer to the SonoSite SII Stand Assembly Instructions, available with the
stand and at www.sonosite.com.
WARNING: To avoid the risk of patient injury, misdiagnosis, or user injury, read all the
warnings in the ultrasound system user guide and supplemental guides.

2
Conventions
The user guide follows these conventions:
A WARNING describes precautions necessary to prevent injury or loss of life.
A Caution describes precautions necessary to protect the products.
A Note provides supplemental information.
Numbered steps in procedures must be performed in order.
Items in bulleted lists do not require a sequence.
Single-step procedures begin with .
Symbols and terms used on the system are explained in the ultrasound system user guide.
Customer assistance and comments
Questions and comments are encouraged. FUJIFILM SonoSite is interested in your feedback regarding the
system and the user guide. Please call FUJIFILM SonoSite at 888-482-9449 in the U.S. Outside the U.S., call the
nearest FUJIFILM SonoSite representative.
For technical support, please contact FUJIFILM SonoSite as follows:
FUJIFILM SonoSite Technical Support
Phone
(U.S. or Canada)
877-657-8118
Phone
(outside U.S. or
Canada)
425-951-1330, or call your local representative
Fax [phone]
Email ser[email protected]
Web www.sonosite.com
Europe Service
Center
Main: [phone]
English support: [phone]
French support: [phone]
German support: [phone]
Italian support: [phone]
Spanish support: [phone]
Asia Service Center [phone]

English Deutsch Español Français Italiano Português
SonoSite SII Stand User Guide 3
Stand features
The stand provides a mobile work platform and a storage area for transducers and other supplies. It also
provides connections for accessories and peripherals.
Figure 1 SonoSite SII Stand: Back and front views (shown with ultrasound system installed)
* An optional second storage bin is available for purchase.
1 DC power cord 7 Printer shelf (optional)
2 Transducer holder 8 Storage bin*
3 Wiring bracket 9 Cord wrap bracket
4Heightadjustmentlever 10AC cord retainer (optional)
5 Tray and drawer 11 Wheel lock lever
6 Gel bottle holder
7
11
8
2
6
4
1
5
9
10
3

4
Attaching and removing the ultrasound system
Be careful to always support the weight of the ultrasound system when attaching or removing it from the
stand.
To attach the ultrasound system
1Place the transducer holder on the mounting plate.
2Place the back of the system onto the mounting plate.

English Deutsch Español Français Italiano Português
SonoSite SII Stand User Guide 5
3Turn the four captive fastener screws clockwise by hand into the holes in the back of the system until the
system is securely in place.
4Tighten the fasteners with a Phillips-head screwdriver.
A driver and Phillips-head insert is included with the stand.
To connect AC power
Connect the following cords:
DC power cord
System AC power cord

6
To connect cords to the wiring bracket
Attach the cords to the matching slots in the wiring bracket.
To remove the ultrasound system
1Support the ultrasound system so that it does not fall when loosened.
2Turn the screw counterclockwise in each of the four corners of the mounting plate. If necessary, use a
Phillips-head screwdriver.
3Remove the system from the stand.
The system lifts off the two mounting plate pegs.
WARNING:
To avoid the risk of personal injury or damage to the ultrasound system, support
the full weight of the ultrasound system while loosening and removing it from
the stand.

English Deutsch Español Français Italiano Português
SonoSite SII Stand User Guide 7
Adjusting the height and angle of the stand
To raise or lower the ultrasound system
1Lock two or more wheels.
2Make sure that the area above the column is clear.
3Loosen the height-adjustment lever by turning it counter-clockwise.
The pole is spring-loaded, and the system will rise from the column automatically, unless it is already at its
maximum height.

8
4Raise or lower the system to the desired height, and then tighten the height-adjustment lever by turning it
clockwise.
If you cannot rotate the height-adjustment lever due to an obstruction (for example, the ultrasound system
or an accessory is in the way), you can reposition the lever by pulling the lever outward, turning it to the
desired position, and then releasing it.
To adjust the system angle
1Lock two or more wheels.
2Grasp the handle on the front of the ultrasound system, and then tilt and rotate the system to the desired
angle.
Caution: When lowering the pole, avoid grasping its base. Skin could get caught and
pinched in the gap.

English Deutsch Español Français Italiano Português
SonoSite SII Stand User Guide 9
Moving and locking the stand
To lock the stand
Push down on each wheel’s locking lever.
To move the stand
1Unlock each wheel by pushing up on the locking lever.
2Grasp the stand firmly by the tray assembly, and move the stand to the new location.
WARNINGS:
To help avoid injury or equipment damage that could result from the stand
toppling over:
Adjust the height of the system to its lowest possible setting on the stand
before moving the stand.
Move the stand by pushing the tray assembly. Do not push or pull the stand
using the handle on the front of the SonoSite SII ultrasound system.
Do not apply undue force when moving the stand.

10
3When you have finished moving the stand, lock at least two of the wheels by pushing down on the locking
lever.
Troubleshooting
Issue Solution
Printer does not print. Check the printer selection on the Connectivity settings page.
For more information, see the SonoSite SII user guide.
Check the cable connections. For more information, see the
SonoSite SII Stand Assembly Instructions.
Ensure that the printer is turned on and set up properly. See the
printer manufacturer’s instructions, if necessary.
Stand tips over more easily
than expected.
Lower the pole to lower the ultrasound system.
Avoid placing or hanging heavy objects on the stand. Too much
weight can cause the stand to become less stable.

English Deutsch Español Français Italiano Português
SonoSite SII Stand User Guide 11
Cleaning and disinfecting
To clean and disinfect the stand
You can clean and disinfect the exterior surface of the stand using a recommended cleaner or disinfectant. For
the most recent list of approved products, see www.sonosite.com.
1Turn off the ultrasound system and any accessory equipment. Disconnect the system and accessory
equipment from AC power.
2Clean the stand surfaces to remove any debris or bodily fluids. Use the following procedure:
aUse either a pre-moistened wipe or a soft cloth dampened with cleaner or disinfectant.
bRemove all gel, debris, and bodily fluids from the stand.
WARNINGS:
To avoid electrical shock, before cleaning, always disconnect the system from
the power supply.
To avoid injury, always use protective eyewear and gloves when performing
cleaning and disinfecting procedures.
To avoid infection, ensure that the solution expiration date has not passed.
To avoid infection, the level of disinfection required for a product is dictated by
the type of tissue it comes into contact with during use. Ensure that the
solution strength and contact time are appropriate for the equipment. For
information, see the disinfectant label instructions and the recommendations
of the Association for Professionals in Infection Control and Epidemiology
(APIC) and FDA.
Caution: Use only recommended cleaners or disinfectants on surfaces. Immersion-type
disinfectants are not tested for use on surfaces.
Approved cleaners and disinfectants for the stand
Cleaner/disinfectant Minimum wet contact time1
SaniCloth AF3 (gray top)23 minutes
SaniCloth Plus (red top) 3 minutes
PI-Spray II 20 minutes
1For maximum effectiveness, the component being cleaned must remain wet with disinfectant for a
minimum period of time.
2Qualified for use as an intermediate-level disinfectant for mycobacteria. For a more complete list, refer to
the cleaners and disinfection document available at www.sonosite.com

12
cWith a new wipe, clean all parts of the stand by wiping from the clean areas to the soiled areas. This
method helps to avoid cross-contamination.
dObserve the minimum wet contact time. Monitor the stand parts for wet appearance. Reapply with a new
wipe if no longer wet.
3Allow the stand to air dry in a clean, well-ventilated space.
For information about cleaning the peripherals, see the manufacturer’s instructions.

English Deutsch Español Français Italiano Português
SonoSite SII Stand User Guide 13
Safety
For maximum safety, observe the following warnings and cautions before using accessories and peripherals
with the SonoSite SII ultrasound system and transducers.
Electrical safety
Equipment safety
WARNINGS:
To avoid the risk of electrical shock and possible fire:
Do not plug the power cord of the SonoSite SII stand into a multiple portable
socket outlet (MPSO); do not use an extension cord.
Use only properly grounded equipment. Shock hazards exist if the power
supply is not properly grounded. Grounding reliability can only be achieved
when equipment is connected to a receptacle marked“Hospital Only,”
“Hospital Grade,”or the equivalent. The grounding wire must not be removed
or bypassed.
Do not connect more than one peripheral at a time.
Inspect the power supply, plugs, cables, and power cords on a regular basis for
damage.
Use only accessories and peripherals recommended by FUJIFILM SonoSite,
including the power supply. Connection of accessories and peripherals not
recommended by FUJIFILM SonoSite could result in electrical shock. Contact
FUJIFILM SonoSite or your local representative for a list of accessories and
peripherals available from or recommended by FUJIFILM SonoSite.
WARNING: To avoid tipping, and the risk of personal injury or damage to the system, do not
move the stand using the handle on the front of the ultrasound system.

14
Clinical safety
Electromagnetic compatibility (EMC)
See the safety section of the ultrasound system user guide and supplemental guides for information on
electromagnetic compatibility with IEC 60601-1-2, including the Manufacturer’s Declaration.
Cautions:
Excessive bending or twisting of cables can cause a failure or intermittent
operation.
Improper cleaning or disinfecting of any part of the accessories and peripherals
can cause permanent damage. For cleaning and disinfecting instructions, see
“Cleaning and disinfecting” on page 11 and the manufacturer’s operating
instructions.
Use only peripherals recommended by FUJIFILM SonoSite.
Accessible metal on the signal inputs and outputs on the back and side of the
ultrasound system is not protectively earthed. Do not perform a high current
ground impedance test involving this part.
WARNING:
To avoid misdiagnosis, do not use non-medical (commercial) grade peripheral
monitors. These monitors have not been verified or validated by FUJIFILM
SonoSite as being suitable for diagnosis.

English Deutsch Español Français Italiano Português
SonoSite SII Stand User Guide 15
Labeling symbols
Symbol Definition
Class 1 device requiring verification by the Notified Body of sterilization or
measurement features, or to a Class IIa, IIb, or III device requiring verification or
auditing by the Notified Body to applicable Annex(es) of 93/42/EEC
Corrugated recycle
Dangerous voltage
Date of manufacture
Direct Current (DC)
Do not get wet.
Do not stack over 2 high.
Do not stack over 5 high.
Do not stack over 10 high.
Fragile

16
Specifications
For information on the peripherals, see the manufacturer’s specifications.
Stand dimensions
Width: 51 cm (20 in.)
Length: 59 cm (23 in.)
Height: 137 cm (54 in.) max., 104.75 cm (41.25 in.) min.
Height range: 32.25 cm (12.7 in.)
Safe working load per bin: 5 kg (11 lbs.)
Paper recycle
To avoid tipping, do not move the system using the handle on the front of the
SonoSite SII ultrasound system.
When moving the system, push the stand using the tray.
Maximum weight load
WARNING:
Connect Only
Accessories and
Peripherals
Recommended
by FUJIFILM
SonoSite
WARNING: Connect Only
Accessories and Peripherals
Recommended by FUJIFILM SonoSite
Symbol Definition

English Deutsch Español Français Italiano Português
SonoSite SII Stand User Guide 17
Weight:
16.8 kg (37 lbs.)
45kg (100 lbs.) maximum total weight with system and accessories.
Temperature and humidity limits
Operating: 10–40°C; 15–95% R.H.
Shipping/Storage: -35–65°C; 15–95% R.H.
Peripherals
Printer
For instructions on installing and setting up the printer, see the Printer Installation Instructions. For printer
paper, contact Sony at 1-800-686-7669 or www.sony.com/professional to order paper or to find a local
distributor.
Storage bin
AC cord retainer
Gel bottle holder
Tray and drawer assembly
Wiring bracket

18