FURNITUREBOX ALMA User manual

ALMA
MEDIUM CHEST OF DRAWERS
ASSEMBLY GUIDE
www.furniturebox.co.uk
Scan QR code for more tips,
advice and assembly video or visit
furniturebox.co.uk/club/alma-medium-chest
SCAN ME

• Check you have all the components and
tools listed.
• Remove all ttings from the plastic bags
and separate them into their groups.
• We do not recommend the use of power
drills/drivers for inserting screws, as this
could damage the unit. Only use hand
screwdrivers and Allen keys.
• Keep children and animals away from the
work area, small parts could cause choking
if swallowed.
• Make sure you have enough space to
layout the parts before starting.
• Assemble the item as close to its nal
position (in the same room) as possible.
• Do not overtighten the nuts to avoid
causing damage to the threads.
Important - Please read these instructions fully before starting assembly
SAFETY AND
CARE ADVICE
!
NO POWER TOOLS
Follow us on Instagram
@furniturebox_uk
• Only clean using a damp
cloth and mild detergent,
do no use bleach or
abrasive cleaners.
• From time to time check
that there are no loose
screws on this unit
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre
SAFETY AND CARE ADVICE

www.furniturebox.co.uk
PLEASE CHECK CAREFULLY AND MAKE SURE YOU HAVE ALL
FITTINGS AND TOOLS LISTED BELOW BEFORE YOU START.
NOTE: The quantities above are the correct amount to complete the assembly. In
some cases more ttings may be supplied than are required.
IMPORTANT INFORMATION
TWO
PERSON
45 MINUTE
BUILD
MAXIMUM
CAPACITY 50Kg

Follow us on Instagram
@furniturebox_uk
STEP 2
Connect side boards (3) and (4) with link
boards (6) and (7) together, use cam lock
nut (B) to tighten. Due to link boards
(6) and (7) being the same size, ensure
that you choose the correct piece as
per diagram, and that it is assembled
correctly, to prevent confusion.
STEP 1
Put the pieces on a soft at
surface e.g. a carpet to avoid
scratching or bumping. Make
sure that you have all pieces
and components ready to
build the chest of drawers.
Insert cam screw (A) and
wooden dowel (C) into
corresponding holes of top
board (1), bottom board (2),
side boards (3) and (4).
STEP 3
Connect the partition
board (5) with top
board (1), tighten with
cam lock nut (B).

www.furniturebox.co.uk
STEP 4
Insert the back boards (15) and (17)
into the slots (3) and (4) of the side
boards, then attach the back xing
(16)
FULL ASSEMBLY INSTRUCTIONS
STEP 5
Connect top boards (1) & (5) with the side
board (3) & (4) and the back board (15).
Tighten with cam lock nut (B).
Make sure both top drawers inner length
(either side of partition board (5) is 42cm,
and the partition board (5) vertically
connected with the both link board (6),
Use self tapping screw (D) to tighten.
Connect the bottom board (2) with
side boards (3) & (4), tighten with screws
(E).
STEP 6
Install the wooden legs (G) in the
corresponding position on
the bottom board (2).
Stick the waterproof pad (H) on the
end of each leg.

STEP 8
Install the assembled drawers in turn.
Make sure that the left and right
drawers in the top are installed correctly
/ the correct way round
Use screw (D) to tighten back board (15).
Then use fastening clips to secure
cabinet back with 16mm screws.
We strongly recommend you use the
anti-tipping kit to anchor/secure your
chest of drawers to the wall to prevent it
tipping over.
STEP 7
Assemble the drawers:
Connect small drawer front (8) with
drawer sides (12), (9) and bottom (13)
together.
Then connect drawer front (10) with
drawer sides (12), (11) and bottom (14)
together, use self tapping screw (D)
to tighten.
There are white plastic clips already
installed on the insides of the side
boards. Ensure you attach these
to your drawers. This is to stop the
drawers dropping from the cabinet.
ATTENTION: Be careful not to
overload drawers.

www.furniturebox.co.uk

The cushions (foam inserts and
covers) are not covered by the guarantee.