FURNITUREBOX ROMERA User manual

ROMERA TV STAND
ASSEMBLY GUIDE
www.furniturebox.co.uk
Scan QR code for more tips, advice and
assembly video or visit
furniturebox.co.uk/club/romera-TV-stand
SCAN ME

• Check you have all the components and
tools listed.
• Remove all ttings from the plastic bags
and separate them into their groups.
• We do not recommend the use of power
drills/drivers for inserting screws, as this
could damage the unit. Only use hand
screwdrivers and Allen keys.
• Keep children and animals away from the
work area, small parts could cause choking
if swallowed.
• Make sure you have enough space to
layout the parts before starting.
• Assemble the item as close to its nal
position (in the same room) as possible.
• Do not overtighten the nuts to avoid
causing damage to the threads.
Important - Please read these instructions fully before starting assembly
SAFETY AND
CARE ADVICE
!
NO POWER TOOLS
Follow us on Instagram
@furniturebox_uk
• Only clean using a damp
cloth and mild detergent,
do no use bleach or
abrasive cleaners.
• From time to time check
that there are no loose
screws on this unit
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre
SAFETY AND CARE ADVICE

www.furniturebox.co.uk
PLEASE CHECK CAREFULLY AND MAKE SURE YOU HAVE ALL
FITTINGS AND TOOLS LISTED BELOW BEFORE YOU START.
NOTE: The quantities above are the correct amount to complete the assembly. In
some cases more ttings may be supplied than are required.
IMPORTANT INFORMATION
TWO
PERSON
MAXIMUM
CAPACITY 100Kg
30 MINUTE
BUILD

Follow us on Instagram
@furniturebox_uk
STEP 2
Turn over bottom panel [1] so it
rests on its feet.
Attach side 2 x side panels [4]
in locations shown on diagram,
using 2 x washer [A] followed by
2 screw [C] inserted from bottom
upwards into panel. Tighten with
Allen key [H].
Insert 2 x wooden dowel [E] and
2 x cam bolt [G] into the thin
edge of each side panels. Add
cam bolts [G] into holes on the
sides of the panels. Take care
to put dowels and bolts in their
correct holes. Don’t tighten the
cam nuts yet.
Add 2 x wooden dowels into the
inner holes on the far end of
bottom panel [1].
STEP 1
Use a clear, at, soft surface to
avoid bumps or scratches.
Palace bottom panel [1} upside
down on the oor and attach feet
blocks [2] and [3] using washer [A]
followed by screw [B] in each hole.
Tighten with Allen key [H]

www.furniturebox.co.uk
STEP 4
Add shelf [6] - carefully align
holes in shelf with dowels and
cam bolts.
Add 2 x wooden dowels into the
top of shelf panel [6].
Tighten the cam nuts below
shelf [6] to secure it into place.
STEP 3
Attach side panel [5] to the bottom
panel and secure with washer
[A] followed by screw [C] inserted
from bottom upwards into panel.
Tighten with Allen key.
Add 2 x wooden dowels and 2 x
cam bolts [G] to the top thin edge
of side panel [5}. Add cam nuts
[F] in corresponding holes. Don’t
tighten the cam nuts yet.
FULL ASSEMBLY INSTRUCTIONS

STEP 6
ATTENTION: Carefully align top panel [7]
with the dowels and cam bolts.
Tighten the cam bolts.
Cover all cam nut holes with stickers [D].
Your TV stand is now ready to use.
STEP 5
Add another side panel [4] on
top of shelf [6].
Add 2 x wooden dowels
and 2 x cam bolts into the
thin edge of the side panel.
Pop cam nuts into the
corresponding holes in the
side of panel [4]

www.furniturebox.co.uk

The cushions (foam inserts and
covers) are not covered by the guarantee.