Furuno TECDIS User manual

TECDIS Installation Manual Page 0
A fully type approved Electronic Chart and
Display Information System (ECDIS),
certified by DNV.
Installation Manual
Software edition: 4.7.1
Manual edition: 2.1

TECDIS Installation Manual Page 1
The PC Main board is equipped with a
litium battery. The lithium battery should
be replaced only in the factory.
There is a danger of explosion if the wrong
type of battery is used for replacement.
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
Standard
compass
Steering
compass
HT405P4 TEL-A1 2.20m 1.50m
JH 19T14 MMD 0.85m 0.45m
JH 20T17 MMD 0.75m 0.35m
JH 23T12 MMD 1.60m 1.05m
BTC5100C PS/2 0.3m 0.3m
DNH HP-6 1.5m 1.0m
DHN HPS-6 1.5m 1.0m
Furuno RCU-018 0.30m 0.30m

TECDIS Installation Manual Page 2
GENERAL INTRODUCTION TO THE INSTALLATION MANUAL................................. 4
STANDARDS COMPLIANCE.................................................................................................... 5
EQUIPMENT LISTS:................................................................................................................... 6
INSTALLATION OVERVIEW................................................................................................... 7
SPECIFICATIONS:...................................................................................................................... 8
CHAPTER 1: MOUNTING....................................................................................................... 12
1.1 MONITOR UNIT ....................................................................................................................... 12
1.2 PROCESSOR UNIT.................................................................................................................... 16
1.3 CONTROL UNIT FURUNO RCU-018........................................................................................ 18
1.4 KEYBOARD AND TRACKBALL.................................................................................................. 22
1.5 ADDITIONAL UNITS ................................................................................................................. 23
1.6 TRACK CONTROL:ANSCHÜTZ NP 2025 PLUS ..................................................................... 28
1.7 NAUT AW: GYRO SENSOR INPUT REQUIREMENTS ............................................................. 29
CHAPTER 2: WIRING AND SIGNAL DISTRIBUTION ..................................................... 30
2.1 WIRING DIAGRAM (HT 405P4 TEL-A1):.............................................................................. 31
2.2 SIGNAL DISTRIBUTION DIAGRAM (INTERNAL DATA FLOW):.................................................. 32
2.3 PROCESSOR CONNECTORS,HT 405P4 TEL-A1 .................................................................... 33
2.4 ETHERNET CONNECTORS AND CABLE .................................................................................... 34
2.5 OTHER CONNECTORS.............................................................................................................. 35
CHAPTER 3: PARAMETER SETUP ...................................................................................... 36
3.1. SERVICE MODE (WINDOWS).................................................................................................. 36
3.2. NMEA DATA SETUP............................................................................................................... 36
3.2.1 INPUTS................................................................................................................................... 37
3.2.2 SPEED.................................................................................................................................... 37
3.2.3 OUTPUTS ............................................................................................................................... 38
3.2.4 PORT ACTIVITY ..................................................................................................................... 38
3.2.5 RECEIVED DATA .................................................................................................................... 38
3.2.6 OTHER COM PORT CONNECTIONS ......................................................................................... 38
3.2.7 SUPPORTED NMEA SENTENCES............................................................................................ 39
3.3 SPECIFICATION ....................................................................................................................... 41
3.3.1 SAVE AND RESTORE SETUP DEFAULT VALUES........................................................................ 42
3.4 TECDIS NMEA AND TCP/IP SERVER.................................................................................. 43
3.5 CHART INSTALLATION /MISC................................................................................................ 44
3.5.1 INSTALL,UPDATE OR REMOVE CHART DATABASES................................................................ 44
3.5.2 ENTER VESSEL INFORMATION:............................................................................................... 45
3.5.3 SEND REGISTRATION.............................................................................................................. 46
3.5.4 START C-MAP CHART MANAGER.......................................................................................... 46

TECDIS Installation Manual Page 3
3.5.5 MONITOR CALIBRATION AND TEST ....................................................................................... 47
3.6 LICENSING............................................................................................................................... 48
3.6.1 TECDIS LICENSE .................................................................................................................. 48
3.6.2 C-MAP LICENSE ................................................................................................................... 49
3.6.3 DYNAMIC LICENSING ............................................................................................................ 49
3.7 TRACK CONTROL.................................................................................................................... 50
3.7.1. STARTING REQUIREMENTS ................................................................................................... 50
3.7.2 DEFAULT VALUES NEW ROUTE .............................................................................................. 51
3.7.3 OTHER SETTINGS ................................................................................................................... 51
3.8 ROUTE SYNCHRONIZATION .................................................................................................... 52
3.8.1 BASIC METHOD ..................................................................................................................... 52
3.8.2 AUTOMATIC METHOD (REPLICATION)................................................................................... 52
CHAPTER 4: OPERATIONAL SYSTEM SETTINGS.......................................................... 54
4.1. SETUP ..................................................................................................................................... 54
4.1.1. NMEA DATA INPUTS:............................................................................................................. 55
4.2. OPERATIONAL PARAMETERS FOR THE SHIP ......................................................................... 55
4.2.1. OWN SHIP OFFCENTER .......................................................................................................... 55
4.2.2. AUTO SENSITIVITY................................................................................................................ 55
4.2.3. SHOW DOUBLE CIRCLE.......................................................................................................... 55
4.2.4 SHOW SHIP OUTLINE .............................................................................................................. 55
4.2.5. COURSE VECTORS................................................................................................................. 55
4.2.6. WHEELOVER......................................................................................................................... 55
4.3. OPERATIONAL PARAMETERS FOR AIS.................................................................................. 56
4.3.1. DISPLAY FILTER:RANGE AND TRACK................................................................................... 56
4.3.2. DISPLAY FILTER:ALL TARGETS ACTIVE ............................................................................... 56
4.3.3 DISPLAY FILTER:HIDE CLASS B ............................................................................................ 56
4.3.4 DISPLAY FILTER:RELATIVE COG VECTORS .......................................................................... 56
4.3.5 LOST ACTIVE TARGETS .......................................................................................................... 56
4.3.6 DANGER CPA ALL TARGETS.................................................................................................. 56
4.4 CHART LIBRARY...................................................................................................................... 57
4.5 IMPORT OF S57 DATA.............................................................................................................. 58
4.6 IMPORT OF S-63 CHART DATA ................................................................................................ 59
CHAPTER 5: MISCELLANEOUS........................................................................................... 60
5.1 ERROR MESSAGES .................................................................................................................. 60
5.2. MONITOR CALIBRATION ....................................................................................................... 62
CHAPTER 6: CHECKLISTS REGARDING INSTALLATION .......................................... 64
6.1 CHECKLIST PRIOR TO COMPLETION OF TECDIS INSTALLATION......................................... 64
6.2 CHECKLIST PRIOR TO COMPLETION OF TECDIS TCS AND TECDIS AW INSTALLATION. 66
6.3 ADDITIONAL CHECKLIST PRIOR TO COMPLETION OF TECDIS AW INSTALLATION............ 73
6.4 INSTALLATION NOTES ............................................................................................................ 74

TECDIS Installation Manual Page 4
General introduction to the installation manual
This manual is describing the procedure to ensure a proper and safe installation of our TECDIS
onboard a vessel. Please read carefully this manual before you start up the commissioning of the
TECDIS.
The installation and commissioning of the TECDIS must be performed by an authorized service
engineer, which has undertaken training or in other forms gained the required skills to perform an
authorized installation of a TECDIS system onboard a vessel.
To ensure a professional after-sale service and a personal track-record of TECDIS installations,
we recommend that the service engineer saves the default setup file to floppy disk or other
media. He can then keep this file in his personal register of TECDIS installations.
The file is located at: C:\Program files\TECDIS\dta4.setup, or C:\Program
files\TECDIS\Telchart.ini (if present).
Please note the following:
All position inputs to TECDIS from all external sensors must be in WGS-84
datum.
TECDIS shall be supplied by UPS (uninterrupted power supply) 220VAC or
emergency power, this shall include also TECDIS backup (if installed) and other
hardware related to the TECDIS installation. A dedicated UPS shall be supplied
to each TECDIS (if dual installation). The UPS or emergency power shall have
sufficient capacity to supply all required equipment for a period of at least 60
seconds.
If connected to internet to provide C-Map Update Service functionality, a switch
must be made available to disconnect TECDIS from internet when C-Map
Update Service functionality is not in use.
Checklist to verify the proper installation of the TECDIS shall be filled in and
filed onboard. For TECDIS TCS and TECDIS AW, a copy of this checklist shall
be sent to Telko AS for full type approval compliance. For all versions of
TECDIS, it is strongly recommended that a copy is stored in the installer’s
archives and that a copy is sent to Furuno Norway or Telko AS.

TECDIS Installation Manual Page 5
Standards Compliance
TECDIS conforms to the following standard(s) or other normative documents:
Version 4.7.1 and higher:
•Marine Equipment Directive, Module B (MED-B)
•IMO Resolution MSC.232(82)
•IMO Resolution MSC.191(79)
•IMO Resolution MSC.74(69) Annex 2,
•IMO Resolution A.694(17).
Version 4.6.0 to 4.7.0:
•Marine Equipment Directive, Module B (MED-B)
•IMO Resolution MSC.74(69) Annex 2,
•IMO Resolution A.817(19) as amended by MSC.64(67) Annex 5 and by
MSC.86/70) Annex 4
•IMO Resolution A.694(17).
For a current overview of software versions, standards compliance and
instructions for updating TECDIS software to comply with new standards and
regulations, refer to the following web site:
http://www.telko.no/site/support/tecdis/compliance

TECDIS Installation Manual Page 6
Equipment lists:
Standard Supply
Name Type Qty Remarks
Computer HT405P4 TEL-A1 1 1,9 m power cable
Monitor JH 20T17 MMD 1 2,0 m video cable
1,9 m power cable
TECDIS keyboard BTC-5100C 1 1,3 m cable
TECDIS mouse Mouse-trak B-MPIND-
XROHS
1 1,9 m cable
Serial interface RS-422 MOXA OPT8F 1 1,5 m cable
Optional Supply
Name Type Qty Remarks
Monitor JH 19T14 MMD 1 2,0 m video cable
1,9 m power cable
Monitor JH 20T17 MMD 1 2,0 m video cable
1,9 m power cable
Monitor JH 23T12 MMD 1 2,0 m video cable
1,9 m power cable
Fan Regulation Kit JH KIT HT405P4TEL-A1 1
Telko Alarm Interface TEA-01 1 1,4 m cable
Bracket for monitor JH MMD BR 1
Audio amplifier PCI card HT 00072 OPT-A1 1
Speaker (bracket mount) DNH HP-6
(See note 1)
1 0,5 m cable
Speaker (flush mount) DNH HPS-6
(See note 1)
1 0,5 m cable
Analog signal collector TA3232-1 1 T Adapter
Control Unit Furuno RCU-018 1
Note 1: Loudspeaker required when display unit or control unit does not contain a buzzer

TECDIS Installation Manual Page 7
Installation Overview

TECDIS Installation Manual Page 8
Specifications:
Processor HT 405P4 TEL-A1:
• 4U – 19” Rack Mount Computer
• Intel Pentium 4 – 3.4 GHz (S775)
• Dual Head Video Card
MATROX P650 PCI-E
• 1GB RAM (Max 2GB)
• 80GB 2.5” Hard drive
• DVD/CD-R/W Dual (48x/16x/6x/8x)
• 1,44MB 3,5” FDD
• 2x 10/100/1000Mbps Ethernet LAN
• 4x RS-232 Serial Ports
• 8 ports RS-422 serial interface MOXA
C218T-PCI with external optoisolated
Interface OPT-8F
• 1x Parallel Port
• 6x USB 2.0 ports
• Standard PS/2 (keyboard & mouse)
• Dim: 427 (W) x 176 (H) x 480 (D) mm
• 110/230V (400W)
Monitor JH 20T17 MMD:
•20,1 inch viewable image size
•A-Si (Thin Film Transistor) Active matrix,
•Pixel number: 1600x1200
•Pixel pitch (RGB): 0,255 mm H/V
•Response time: 20 ms
•Contrast ratio: 700:1
•Light intensity: 300 cd/m2
•Viewable angle: +- 85 deg. H/V/L/R
•Active display area: 408x306 mm H/V
•Auto detects VGA to SXGA
•Optimum picture with 60 Hz
•Input signal: DVI-D, DVI-D input 24pin
•Input signal: RGB, 15pin mini D-SUB
•Input signal: Multifunction
•AC power: 115 VAC/ 60 Hz
230 VAC/ 50 Hz (100 W max)
•Weight: 13,5 kg
Monitor JH 19T14 MMD:
•19,0 inch viewable image size
•Active matrix, Thin Film Transistor
•Pixel number: 1280 x 1024
•Pixel pitch (RGB): 0,294 mm H/V
•Response time: 12 ms
•Contrast ratio: 900:1
•Light intensity: 300 cd/m2
•Viewable angle: +- 85 deg. H/V/L/R
•Display area: 376.32x301.056 mm H/V
•Auto detects VGA to SXGA
•Optimum picture with 60 Hz
•Input signal: DVI-D, DVI-D input 24pin
•Input signal: RGB, 15pin HD D-SUB
•Input signal: Multifunction
•AC power: 115 VAC/ 60 Hz
230 VAC/ 50 Hz (100 W max)
•Weight: 11,5 kg
Monitor JH 23T12 MMD:
•23,1 inch viewable image size
•Thin Film Transistor Active matrix,
•Pixel number: 1600x1200
•Pixel pitch (RGB): 0,294 mm H/V
•Response time: 20 ms
•Contrast ratio: 500:1
•Light intensity: 250 cd/m2
•Viewable angle: +- 85 deg. H/V/L/R
•Active display area: 470.4x352.8 mm H/V
•Auto detects VGA to UXGA
•Optimum picture with 60 Hz
•Input signal: DVI-D, DVI-D input 24pin
•Input signal: RGB, 15pin mini D-SUB
•Input signal: Multifunction
•AC power: 115 VAC/ 60 Hz
230 VAC/ 50 Hz (100 W max)
•Weight: 20 kg

TECDIS Installation Manual Page 9
Mouse-Trak B-MPIND-XROHS:
Functional Specifications:
Resolution: 192 to 576 pulses per revolution of the ball.
Input Switches: Three (3)
Interface: IBM PS/2
Connector: 6-Pin Mini-DIN Male
Pin Assignments: Pin 1 = PS/2 Data
Pin 2 = NC
Pin 3 = Common
Pin 4 = +5V
Pin 5 = PS/2 clock
Pin 6 = NC
Compatibility: Microsoft PS/2 Mouse Protocol, Logitech PS/2 Mouse
Protocol
Switches: Mechanically limited, break resistant
Cable: 96”+-0.5”
Power Consumption: Idle: 8mA
Max: 12mA
Mechanical Specifications:
Dimensions: Approximately 4”wide x 8”long
Weight: 1.3 lbs.
Body Material: Glass filled Xenoy thermoplastic, black
Ball Material: Cast Phenolic Resin
Ball Hardness: Rockwell H 85
Tracking Force: 1.5 oz. maximum, 0.5 oz. typical (15g)
Ball Load: 250 lbs. maximum downward
Ball Speed: 500 RPM maximum
Hand Pad: Injection-molded vinyl, black
Environmental Specifications:
Operating
Temperature: 0 to +50 degrees Celsius
Storage Temperature: -20 to +60 degrees Celsius
Humidity: 0 to 95% non condensing

TECDIS Installation Manual Page 10
Speaker HP-6/HPS-6:
Material/Color Polyamide UL94 V0 / RAL 7035
Mounting Bracket
Termination Cable,0,5m
Weight 0.5 kg
IP-rating (UL
Equivalent) (-) 67
Max. / min. amb.
Temp 90°C / -40 °C
Rated / max. power 6W / 15W
SPL 1W/1m 101 db
SPL rated power 108 db
Effective freq. range 500 – 7500 Hz
Dispersion (-6dB)
1kHz / 4kHz 170° / 70°
Directivity factor, Q 4,3
Telchart Alarm interface, TEA-01:
Outputs: (connector 1,2,3,4)
are a solid state relay LCA110E which has capabilities of max 50VDC, max 200mA.
Input: (connector 5,6)
uses a current limited (6.8 Kohm resistor) opto coupler MCT5211. Reset in at 10-30 VDC.
All input and outputs are electrically isolated.
Shield shall be connected at alarm central side.
Shield are connected in Dsubmin 9f. connector,
but are not cross connected in the interface box.
A 1.5 m Cable with Dsubmin 9p female (PC-serial port) in one end and an interface box with 7
screw terminal in the other end.
Wiring info:
(1)> Alarm Out - (NO)
(2)> Alarm Out + (NO)
(3)> Sound Alarm out reset - (NO)
(4)> Sound Alarm out reset + (NO)
(5)< Sound Alarm inp. Reset – (NO)
(6)< Sound Alarm inp. Reset + (NO)
(7)- Cable shield

TECDIS Installation Manual Page 11
TELchart TA3232-1 analog adapter.
Technical specifications:
Inputs:32 digital inputs
32 analog input (24 x +/- 10VDC and 8 x 4-20mA )
Outputs:
RS422 output ar baudrate 4800,n,8,1 to Furuno VDR
Ethernet TCP/IP serverport at 192.168.0.60 : 2000
Ethernet UDP/IP broadcast at 0.0.0.0 : 2100
The placement of the modules in the box are.
[ADAM4051 #2] [ADAM4017+ #4] [ADAM4017+ #6]
[ADAM6520] [ADAM6500] [ADAM4051 #1] [ADAM4017+ #3] [ADAM4017+ #5]
From left to right as indicated in the picture
ADADM 6520 5 port industrial 10/100 Mb Ethernet switch w/auto direction sense.
ADADM 6500 WinCE processor
2 x ADADM 4051 á 8 x digital inputs
2 x ADADM 4017+ á 8 x analog inputs
2 x ADADM 4017+ á 8 x analog inputs (top one is 8 x 4-20mA inputs)
Powered from 12-30 VDC
Typical consumption 0.4A @24 VDC
Fuses: 2 x 1,6AT

TECDIS Installation Manual Page 12
Chapter 1: Mounting
1.1 Monitor Unit
The monitor unit can be flush mounted in a console panel, or mounted on desktop using optional
accessories.
When selecting a mounting location, keep in mind the following points:
1. Select a location where the display unit can be viewed conveniently and where the screen
can be viewed while facing towards the bow.
2. Select a location where vibrations are down to a minimum, try to avoid vibrations by
adding strength to console where monitor is about to be installed.
3. Locate the unit out of direct sunlight and away from heat sources because of heat that can
build up inside the cabinet.
4. Locate the equipment away from places subject to water splash and rain.
5. Leave sufficient space on the sides and rear of the unit to facilitate maintenance.
6. A magnetic compass will be affected if the monitor unit is placed too close to the
magnetic compass. Observe the compass safe distances to prevent deviation of a magnetic
compass.
7. An optional monitor bracket can be supplied for tabletop installations.
Screws for mounting the monitor to the console are supplied. When bracket is used screws for
attaching bracket and monitor together is supplied. Screws for mounting bracket to table are not
supplied.

TECDIS Installation Manual Page 13
Outline dimensions for JH 20T17 MMD:
Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance
on drawings is +/- 1mm. For accurate measurements, check relevant DWG file, as obtainable
from http://www.hatteland-display.com/maritime_line_displays_series1.php.

TECDIS Installation Manual Page 14
Outline dimensions for JH 19T14 MMD:
Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance
on drawings is +/- 1mm. For accurate measurements, check relevant DWG file, as obtainable
from http://www.hatteland-display.com/maritime_line_displays_series1.php.

TECDIS Installation Manual Page 15
Outline dimensions for JH 23T12 MMD:
Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance
on drawings is +/- 1mm. For accurate measurements, check relevant DWG file, as obtainable
from http://www.hatteland-display.com/maritime_line_displays_series1.php.

TECDIS Installation Manual Page 16
1.2 Processor Unit
The processor unit can be mounted inside on bridge console or other suitable space on the bridge.
When selecting a mounting location, keep in mind the following points:
1. Select a location where vibrations are down to a minimum, try to avoid vibrations by
adding strength to console where the processor is about to be installed.
2. Locate the unit away from heat sources because of heat that can build up inside the
cabinet.
3. Locate the equipment away from places subject to water splash and rain.
4. Leave sufficient space on the sides and rear of the unit to facilitate maintenance and
interconnection cabling.
5. Navigator shall update charts in the processor weekly. Mount the processor at a
location that enables the navigator easy access to front doors of the processor. It
must be possible to open CD drawer of processor without obstructions.
6. The power switch shall be easily to access, front of processor may be flush mounted
in the console to enable access or other means to be provided for easy access.
7. Service key dongle must be possible to remove and insert to enable service technician to
enter service mode.
8. MOXA 8-port RS-422 connection box to be arranged close to processor to enable easy
interconnection. MOXA is supplied with 1,5 m interface cable between processor and
connection box.
Do not protrude the housing with screws to fasten the processor. Straps should be used to fasten
the processor at its location, without protruding the housing. Straps are not supplied and must be
arranged locally. Check that front doors of processor can easily be opened and that cables can
easily arranged in the back of the processor.
The processor is suitable for rack-mounting, 19” width rack. Height is 4U.

TECDIS Installation Manual Page 17
Outline dimensions for HT 405P4 TEL-A1: All figures in mm.

TECDIS Installation Manual Page 18
1.3 Control Unit Furuno RCU-018
The control unit may be mounted on a desktop, with or without the KB fixing metal
(supplied), which mounts the control unit at an angle.
Mounting considerations
When selecting a mounting location, keep in mind the following points:
• Select a location where the control unit can be operated conveniently.
• Locate the unit away from heat sources because of heat that can build up inside the cabinet.
• Locate the equipment away from places subject to water splash and rain.
• Determine the mounting location considering the length of the signal cable between the control
unit and the processor unit.
• A magnetic compass will be affected if the control unit is placed too close to the magnetic
compass. Observe the compass safe distances specified at the start of this manual to prevent
deviation of a magnetic compass.
Fixing with KB fixing plate
1. Fix the KB fixing plate to the bottom of the control unit.
2. Attach three cushions to the bottom of the control unit.
3. Fix it to a desired location with self-tapping screws (local supply).
Fixing without KB fixing metal
1. Drill four mounting holes of 5 mm diameter referring to the outline drawing.
2. Fix the control unit with four screws (M4) from under side of the desktop. (The M4
screws with a sufficient length for the thickness of the desktop should be provided
locally.)
Flush mounting
Use the optional flush mount kit Furuno FP03-09870 to mount the control unit to a console
panel.
Name: Flush mount kit
Type: Furuno FP03-09870
Code No.: 008-535-630
No. Name Type Qty
1 Mount plate 03-163-7531 4
2 Hex bolt M4 4
3 Wing screw M4X30 4
1. Prepare a cutout in the mounting location as shown in the outline figures.
2. Set the control unit to the cutout.
3. Attach the mounting plate to the control unit with four screws from the rear side.
4. Screw the wing screw to each mounting plate and then insert hex bolt to each wing screw.
5. Fasten each wing screw and then fasten the hex nuts as shown in the outline figures.

TECDIS Installation Manual Page 19
Furuno RCU-018 Control Unit outline (Desktop mount)
All figures in mm.