Geco GH21TA User manual

INSTRUCTIONS
FOR CONTROLLER
GH21TA
FOR CENTRAL
HEATING BOILER
CONTROLLER
WITH PISTON
FEEDER
USER MANUAL
We strongly recommend that you familiarise yourself fully with the contents of this manual
before installing and using any of our devices. If you have any questions, please contact us
between 08:00 and 16:00

User Instructions for GECO GH21TA controller
______________________________________________________________________________
Page 2 Edition I 19.06.2013
Table of contents
1. DESCRIPTION OF CONTROLLER ..........................................................................................................................3
2. TECHNICAL SPECIFICATIONS...............................................................................................................................3
3. REQUIRE ENTS FOR ELECTRICAL INSTALLATION.........................................................................................4
5. CONTROLLER ODES............................................................................................................................................6
5.1. S TANDBY ODE .................................................................................................................................................7
5.2. A UTO ATIC ODE - HEATING .............................................................................................................................7
5.3. A UTO ATIC ODE - AINTAIN ...........................................................................................................................8
5.4. ANUAL ODE ..................................................................................................................................................8
5.5. A LAR /N OTE ODE ..........................................................................................................................................9
5.6. E ERGENCY WORK ............................................................................................................................................9
6. OPERATING THE CONTROLLER...........................................................................................................................9
6.1. C ONTROLLER FASCIA PANEL ...............................................................................................................................9
6.2. O PERATING THE CONTROLLER – AIN SCREEN ..................................................................................................11
6.3. P REVIEW OF SYSTE OPERATIONS ....................................................................................................................11
6.4. H ELP BUTTON ..................................................................................................................................................12
6.5. ANUAL ODE ................................................................................................................................................13
6.6. C ONTROLLER ENU – G RAPHIC TREE ................................................................................................................14
7. DESCRIPTION OF ADDITIONAL FUNCTIONS ...................................................................................................20
7.1. DHW PRIORITY ( HOT WATER )........................................................................................................................20
7.2. S U ER FUNCTION ..........................................................................................................................................20
7.3. A NTI - LEGIONELLA FUNCTION ............................................................................................................................20
7.4. GA03HA ROO PANEL ....................................................................................................................................21
7.5. F UEL FEEDER TE PERATURE DETECTION ..........................................................................................................22
7.6. B OILER EXTINGUISHED DETECTION ...................................................................................................................23
7.7. A NTI -S TOP FUNCTION ......................................................................................................................................23
7.8. G RATE ODE ...................................................................................................................................................24
7.9. P U P ONLY ODE ............................................................................................................................................24
7.10. O PERATION RECORD ........................................................................................................................................24
7.11. E ERGENCY WORK ..........................................................................................................................................24
8. SYSTE INSTALLATION......................................................................................................................................25
8.1 H EATING INSTALLATION NU BER 1..................................................................................................................25
8.2 H EATING INSTALLATION NU BER 2..................................................................................................................26
8.3 H EATING INSTALLATION NU BER 3..................................................................................................................27
9. CONTROLLER ALGORITH S FOR ATTACHED DEVICES................................................................................28
9.1 HEATING ODE – FUEL FEEDER .............................................................................................................28
9.2 AUTO ATIC ODE – CH PU PS .............................................................................................................28
9.3 HEATING ODE - FAN ...............................................................................................................................28
9.4 AUTO ATIC ODE – DHW/ IXER PU P.............................................................................................29
9.5 AINTAIN ODE – FAN AND FEEDER....................................................................................................29
10. ALAR S ................................................................................................................................................................30
11. E ERGENCY WORK.............................................................................................................................................36
12. TE PERATURE LI ITER (STB).........................................................................................................................37
13. LOSS OF POWER...................................................................................................................................................38
14. GH03HA ROO PANEL .......................................................................................................................................39
15. IN CASE OF DA AGE TO THE CONTROLLER....................................................................................................40
16. INFOR ATION REGARDING THE LABELING AND DISPOSAL OF WASTE ELECTRONIC AND
ELECTRICAL EQUIP ENT .................................................................................................................................43

User Instructions for GECO GH21TA controller
______________________________________________________________________________
Page 3 Edition I 19.06.2013
1. Description of controller
The GH21TA controller is assembled using microprocessor techniques utilising automatic
surface mounting
This controller is a device used to control the process of preparing domestic hot water
(the DHW circuit), and provides support for the main circuit (circuit CH) Parameters can be
adapted according to the condition and the type of boiler
The controller is equipped with a system to guard against power failure and various types of
interference The controller identifies each emergency and gives a visual and audio warning
The controller automatically supports three installation configurations, which meet the
requirements of the installer fully The device supports three temperature sensor inputs,
digital input for reed relay switch, additional output for room panel GA03HA, and four outputs
for external devices
The GH21TA controller is equipped with:
• Temperature inputs:
- to measure the temperature of the water coming from the boiler
- to measure the temperature of the feeder tray
- to measure the temperature of the water in the boiler / returning CH temperature
•Digital input
- for connecting cotter pin break sensor to boiler piston feeder – reed relay
• Input (RS485)
- Dedicated connector for GECO GA03HA room panel
2. Technical specifications
Supply voltage 230V
~ +10% -15%
Resistance
characteristics of NTC
sensor
Operating temperature od +5°C do +40°C
Humidity od 20% do 80% RH
Temp.
°C
Re
sistance
Ω
Fuse – Fan, Feeder 3.15A 0 7174.89
Sensor type NTC 2.2k
Ω
10 4374.83
Sensor temperature
operating range NTC: 0°C÷100°C 20 2747.10
30 1774.91
40 1172.09
Input Maximum continuous
load 50 795.08
60 547.95
CWU pump 1A 250W 70 384.62
CO pump 1A 250W 80 275.86
Fan* 1A 250W 90 202.37
Feeder* 1A 250W 100 149.16

User Instructions for GECO GH21TA controller
______________________________________________________________________________
Page 4 Edition I 19.06.2013
*When a contactor or relay proxy is connected, use a dedicated blowout
system (eg varistor). Omission of this security measure may result in
malfunction or damage to the controller output.
3. Requirements for electrical installation
WARNING!
Only a person with a valid licence to carry out electrical installation work can install the
controller wiring and connection technologies It is recommended that the work is carried out
by a qualified installation engineer The following are the basic requirements for the electrical
power supply for this particular controller:
1 Repairs, maintenance and other work on the system can be carried out only after
disconnecting the main power supply
2 The room in which the controller is to be installed should be equipped with 230V/50Hz
electrical system in accordance with the applicable regulations
3 The controller should be supplied from a dedicated circuit 230VAC/50Hz grid,
protected by a circuit breaker
4 The controller power cable should have a cross section minimum mechanical strength
of 2 5 [mm2]
5 The cable must be protected from mechanical damage, by keeping it in a duct or
housing
4. Graphic and text descriptions of driver connections
When the cable has been prepared, you will be ready to connect the power to the
controller and temperature sensors, thermostats and other devices:
•The 230 V power supply should be connected to the controller using the terminals marked
“L” and “N” – in inputs 01-02
•The NTC temperature sensor must be connected to the inputs in accordance with the
instructions set out in the tables in section 8, System Installation Please note that the
number of sensors supported depends on the type of installation, and unused sensors do
not have to be connected to inputs
•The room panel GA03HA must be connected to a separate input, as described
•Technological equipment (pumps / fans / feeder) should be connected to the outputs, as
described in the tables in section 8, System Installation and according to the selected
installation

User Instructions for GECO GH21TA controller
______________________________________________________________________________
Page 5 Edition I 19.06.2013
Input parameters are described in the following tables:
Description of controller inputs – temperature sensors
Temperature sensor Type of input Controller designation
Water flowing from
the boiler NTC 50-51
Water in the DHW
boiler/ Return temp NTC 52-53
Fuel feeder NTC 54-55
Description of controller inputs – room thermostat GA03HA
Type of room
thermostat Type of input Controller designation
GH21TA dedicated
room panel - GECO RS485 58-59-60-61
Description of controller inputs – digital
Cotter pin break
sensor for feeder Type of input Controller designation
Reed relay CTC100 56-57
Description of controller outputs – technological equipment
Device installed Type of input Controller designation
CH pump Relay 05-06
DHW pump Relay 07-08
Feeder TRIAC 09-11
Fan TRIAC 12-14

User Instructions for GECO GH21TA controller
______________________________________________________________________________
Page 6 Edition I 19.06.2013
ONLY A QUALIFIED WIRING TECHNICIAN MAY
CONNECT DEVICES TO THE GH21TA CONTROLLER.
5. Controller modes
The controller can be operated in five modes:
•Standby – returns the controller to the state before loss of power The controller
algorithm is not implemented, the clock operates in real time, and the chosen installation
settings are stored
•Automatic - There are two sub-modes, heating and maintain
Heating – in this mode, the algorithm is implemented in the control mode selected
depending on the type of fuel
Maintain - the controller enters this mode if the boiler temperature reaches the set point
In this mode, an individually prepared algorithm is implemented
•anual – This mode is used only to validate the on / off (tests) for each installation of
technological equipment, so when you are sure that tests are finished, go to the automatic
mode
•Alarm – Characterised by the occurrence of an alarm that prevents further operation of
the equipment or the occurrence of a warning, which allows the user to accept temporary
operation under warning conditions accepted by the user with the awareness that it is
temporary in nature When the fault is resolved, the driver returns to the mode it was in
before

User Instructions for GECO GH21TA controller
______________________________________________________________________________
Page 7 Edition I 19.06.2013
•Emergency work – Emergency work allows the boiler to work in case of damage to the
feeder and or fan TRIAC, until servicing is possible
5.1. Standby mode
After the installation procedure described in the previous chapter, the GH21TA driver
is turned on standby In this mode, the screen displays a message about how to select
automatic or manual mode
When the controller is in standby mode, you can switch to manual mode using the
button During normal operation, it is possible to return the controller to standby mode
at any time, by pressing the button
In standby mode, all outputs and the alarm sound signal are disabled When the controller is
switched to automatic mode, the display shows the actual temperature of the water in the
boiler, the set temperature, and information about the controller mode
5.2. Automatic mode - heating
In automatic mode, the controller implements the control algorithm for the chosen heating
schema, according to the heating regulation option chosen Basic information about the
system, displayed on the main screen, includes current and set boiler temperature, and
operating mode The user may choose from three heating regulation options: Standard, grate
mode and pump only

User Instructions for GECO GH21TA controller
______________________________________________________________________________
Page 8 Edition I 19.06.2013
In automatic heating mode, the controller displays text information in the top part of the
screen:
Heating – when the standard regulation option is set
Grate mode H – when the grate mode option is set
Pump only – when the pump only mode is set
A detailed description of non-standard heating regulation options can be found in section 7
5.3. Automatic mode - maintain
The controller enters this mode if the temperature in the boiler reaches that set by the
user in the parameters menu
The fuel feeder and fan are disabled, for the time set by the user in the ‘maintain time’
parameter After this time, the controller turns on the feeder and fan for the time set by the
manufacturer (service parameter S20) It is usual for the fan to operate longer than the feeder
during the time set in service parameter S18, in order to ignite the fuel supplied
The controller will exit maintain mode and return to automatic mode, if the temperature of
the boiler falls below the value set in installation parameter ‘boiler temperature hysteresis’,
which can be edited by the user The central heating pump works in the same way as in
automatic mode
When working in automatic mode maintain, text information is shown in the top part of the
screen:
aintain – when the standard option is set
Grate mode – when grate mode is set
A detailed description of non-standard heating regulation options can be found in section 7
5.4. anual mode
In manual mode, the controller does not implement the control algorithm, and the number
and type of technological devices connected is dependent on the user, who takes
responsibility for the correct operation of the equipment On the main screen, the actual and
set boiler temperature is always displayed The choice of heating regulation option does not
affect the operation of the system in manual mode In this case, the user has full control over
what equipment will be operated by the controller

User Instructions for GECO GH21TA controller
______________________________________________________________________________
Page 9 Edition I 19.06.2013
After entering the manual mode, operation of all equipment will be stopped automatically
The controller working in automatic mode displays text information at the top of the screen –
‘manual mode’
5.5. Alarm/Note mode
Alarm - The controller goes into alarm mode when one of the required sensors fails or is
disconnected, or when the cable is broken The controller will signal that the sensor in
question is required When the fault is repaired, the controller returns to the mode it was in
before The controller will not enter alarm mode when the sensor fault has been repaired Any
changes to components should be done with the controller turned off
Note - The controller switches to warning mode when the DHW/returning sensor fails or is
disconnected, or when the cable is broken The controller then gives information about the
warning, and the types of operations conditionally possible without the sensor The user must
always accept operations that are conditional on the lack of sensor, each time the controller is
restarted This applies only to those sensors which do not affect the safe operation of the
heating system The other functions of the note mode are to give information when the hot
water tank has not been disinfected, or the temperature in the feeder has not been raised The
controller exits the notes mode when one of the notes is UW10 or UW17
5.6. Emergency work.
Safe mode allows the boiler to work in case of damage to the feeder and or fan TRIAC, until
servicing is possible For the controller to operate the feeder / fan in safe mode, the correct
mode should be selected from the menu, in addition to changing the feeder/fan connection A
detailed description is on page 39
6. Operating the controller
Operating the controller is described in this chapter It includes turning it on, using the
keyboard, a working preview of the measuring system, reading text or characters on the
screen, and editing the parameters available to the user
6.1. Controller fascia panel

User Instructions for GECO GH21TA controller
______________________________________________________________________________
Page 10 Edition I 19.06.2013
Button Description Function
Turn on/off The main screen appears
Change modes
Switch between manual and automatic
In the ‘boiler mode bar’, Manual Mode
appears, or in the case of Automatic
Mode, the display reads Heating,
Grate Mode H, Pump only, Maintain,
or Grate mode M
Automatic mode allows a view of
devices, temperature and accompanying
features In manual mode, view
temperature and accompanying
features, and see devices which can be
edited
The screen shows temperature,
devices and accompanying features
From the main screen, go to the user
help menu
From the alarm and note screen, go to
Data service
The screen shows help for users
The screen shows product
information and service helpline
information
Confirm change
Enter Menu from the main screen
Saves change
Goes to Menu from the main screen
Exit without confirming changes
Hold the button for three seconds to go
to the main screen
Exit to previous screen or higher level
menu
Right arrow
Quickly go to boiler output temperature
screen from the main screen
Move to the next column or row on
the right
The screen displays boiler output
temperature
Left arrow
Quickly go to boiler output temperature
screen from the main screen
Move to the next column or row on
the left
The screen displays boiler output
temperature
Up arrow
Increase value
Go to the next position above
Increase the value by one step
Down arrow
Decrease value
Go to the next position below
Decrease the value by one step