Geutebruck G-Cam/E2 Series User manual

G-Cam/EWPC-2275
Full HD IR Bullet IP Camera
Installation

G-Cam/E2 Series Installation
2
Preface
The information given in this manual was current when published. The company
reserves the right to revise and improve its products. All specifications are subject to
change without notice.
Copyright
Under copyright laws, the contents of this user manual may not be copied,
photocopied, translated, reproduced or reduced to any electronic medium or
machine-readable format, in whole or in part, without prior written permission of the
company.
© 2018 by GEUTEBRÜCK All Rights preserved.
Notice
Mounting instructions for Dome Systems and permanently mounted
Cameras especially for Pole Mount.
Please note that the place of mounting should be stiff enough to counter strong
wind or other vibrations!
Otherwise all VCA functions like Motion Detection, Privacy Masking, etc. either in
cameras or with DVRs could be disturbed heavily and can cause unliked and often
alarms. In some cases mechanical problems or defects can be the result of such
vibrations, like overheating of focus motors caused by persistant mast shaking!
This manual provides the installation information for the Outdoor 4K UHD Fix Dome
IP Camera. To work with the Dome Cameras, any installer or technician must have
the following minimum qualifications:
 A basic knowledge of CCTV systems and components
 A basic knowledge of electrical wiring and low-voltage electrical hookups
 A basic knowledge of network system setting
 Have read this manual completely
Important Information
Before proceeding, please read and observe all instructions and warnings in this
manual. Retain this manual with the original bill of sale for future reference and, if
necessary, warranty service. When unpacking the unit, check for missing or
damaged items. If any item is missing, or if damage is evident, DO NOT INSTALL
OR OPERATE THIS PRODUCT. Contact the dealer for assistance.

G-Cam/E2 Series Installation
3
Regulation
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This symbol on the product or on its packaging indicates that this
product shall not be treated as household waste in accordance with
Directive 2002 / 96 / EC. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment. By proper waste handling of this product,
please ensure that it has no negative consequences for the
environment and human health, which could otherwise be caused if
this product is thrown into the garbage bin. The recycling of
materials will help to conserve natural resources.
For more details information about recycling of this product,
please contact the local city office, household waste disposal
service or the shop which purchased the product.
Compliance is evidenced by written declaration from our
suppliers, assuring that any potential trace contamination levels
of restricted substances are below the maximum level set by EU
Directive 2002 / 95 / EC, or are exempted due to their application.

G-Cam/E2 Series Installation
4
Warnings and Cautions
 Handle the camera carefully
Do not abuse the camera. Avoid striking, shaking, etc. The camera could be
damaged by improper handing or storage.
 Installing electricity wiring carefully
Ask qualified personnel of electrical wiring for the installation. Please note the
technical specifications for correct power supply at the end of this manual.
 Do not disassemble the camera
To prevent electric shock, do not remove screws or covers. There are no user
serviceable parts inside. Ask a qualified service person for servicing.
 Do not operate the camera beyond the specified temperature, humidity or
power source ratings
Use the camera under conditions which are described in the technical
specifications.
 Do not use strong or abrasive detergents when cleaning the camera body
Use a dry cloth to clean the camera when it is dirty. In case the dirt is hard to
remove, use a mild detergent and wipe the camera gently.
 Never face the camera towards the sun
Do not aim the camera at bright objects. Whether the camera is in use or not,
never aim it at the sun or other extremely bright objects. Otherwise, the camera
may be smeared or damaged.
Mounting instructions for Cameras especially for Pole Mount.
Please note that the place of mounting should be stiff enough to counter strong
wind or other vibrations!
Otherwise all VCA functions like Motion Detection, Privacy Masking, etc. either
in cameras or with DVRs could be disturbed heavily and can cause unliked and
often alarms.
In some cases mechanical problems or defects can be the result of such
vibrations, like overheating of focus motors caused by persistant mast shaking!

G-Cam/E2 Series Installation
5
Table of Contents
Preface ............................................................................................................................ 2
Regulation ...................................................................................................................... 3
Warnings and Cautions ................................................................................................. 4
Table of Contents .......................................................................................................... 5
1. FEATURES ................................................................................................................. 6
2. PACKAGE CONTENTS .............................................................................................. 7
3. PART NAMES ............................................................................................................. 8
4. INSTALLATION .......................................................................................................... 9
4.1. Installing the camera .......................................................................................................... 9
4.1.1. Installation without bracket .......................................................................................... 9
4.1.2. Compatible accessories ............................................................................................ 12
4.2. Adjusting angle of the camera.......................................................................................... 13
4.3. Adjusting zoom and focus ................................................................................................ 14
4.4. Setting the Image Attributes ............................................................................................. 15
5. CONNECTIONS ........................................................................................................ 16
6. CONFIGURATION .................................................................................................... 19
6.1. Set up network environment ............................................................................................ 19
Generic IP Environment ...................................................................................................... 19
Custom IP Environment .......................................................................................................... 20
6.2. View video on web page .................................................................................................. 21
6.2.1. View video using IPAdmin Tool ................................................................................. 21
6.3. Reboot ............................................................................................................................. 23
6.4. Factory Default ................................................................................................................. 24
6.5. Safe Mode ........................................................................................................................ 25
6.6. Configuration in GEUTEBRÜCK GscSetup ..................................................................... 26
6.3.1. Advanced configuration ............................................................................................. 29
6.7. Configuration in GEUTEBRÜCK G-Set ............................................................................ 31
APPENDIX (A): SPECIFICATIONS .............................................................................. 35
APPENDIX (B): POWER OVER ETHERNET ............................................................... 36
Power Comparison ................................................................................................................. 36
APPENDIX (C): DIMENSIONS ...................................................................................... 37
APPENDIX (D): HEXADECIMAL-DECIMAL CONVERSION TABLE ........................... 38

G-Cam/E2 Series Installation
6
1. FEATURES
Camera
 1/2.9” 1080p CMOS Sony STARVIS Image Sensor
 True Day / Night
 DC Auto Iris Lens
 WDR
 Embedded IR Illuminator
 Remote Zoom/Focus Control (One Click AF)
 Weather proof (IP66)
Video
 H.264 Baseline, Main, High Profile (MPEG-4 Part 10/AVC), MJPEG (Motion JPEG)
 Max 30fps in 1080p
 Text Overlay
 Analog video output
Network
 10 / 100 Base-T Ethernet
Integration
 Software Development Kit (SDK) available
 ONVIF Compliant (Profile S & Profile G)
General
 Micro SD/SDHC slot
Power Over Ethernet (PoE+)

G-Cam/E2 Series Installation
7
2. PACKAGE CONTENTS
Please unpack the package carefully and handle the equipment with care.
The packaging contains:
The above contents are subject to change without prior notice.
Camera DC Power Adaptor & Plugs
Screws (M4x30) and Plastic Anchors Hex Wrench (3mm)
Video Output Cable Silicon Waterproof Band
Ferrite Core Quick Installation Guide
Installation Template CDRom
(Software and Documentation)

G-Cam/E2 Series Installation
8
3. PART NAMES
① Sunshield
② Video Out Cable socket
Socket for the video output cable included in the package (CVBS: 1.0Vp-p / 75Ω BNC)
③ PAL/NTSC button
Pressing the PAL/NTSC button each time changes the mode as follows.
No video output -> PAL-> NTSC*
* Steady output of video until you change the video output mode by pressing the button.
④ Reset button
Use the button to restart the device or to reset it to Factory Default. Refer to 6.3. Reboot and 6.4.
Factory Default for more details.
⑤ microSD memory card slot
Camera supports up to 32GB. A card with Class 4 and higher is recommended for HD recordings.
⑥ Terminal Connector
Connector for cables of digital input/output and audio input/output.
⑦ Power Adaptor Connector
Use DC12V for the power supply.
⑧ LAN connector
RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported).
* Models herein and their appearance are subject to change without any prior
ti
①
⑦
⑥
③
④
⑧
⑤
②

G-Cam/E2 Series Installation
9
4. INSTALLATION
4.1. Installing the camera
4.1.1. Installation without bracket
Installation Template
(Unit: mm)
Installation template’s image size scale in this installation guide is not 1:1.
The correct-size template design paper can be found inside the package se
parately.

G-Cam/E2 Series Installation
10
1) Place the installation template included in
the package on the desired installation
surface.
2) Drill three holes in correct positions based
on the template paper, and insert the anchor
blocks into the holes.
3)Attach the silicon waterproof band
included in the package to the camera’s
mounting surface by aligning it with the three
alignment holes.

4)Install the provided ferrite core on the
cable. For the detailed instructions, refer to
the note on the next page.

5)Connecttherequiredcablestothedevice.
Refertotheimageon5.CONNECTIONSforthe
properconnections.

6)Place the camera body on the installation
surface by matching three alignment holes
with already inserted plastic anchors.

7)  Tighten the plastic anchors with the
screws (M4 x 30) included in the package.


8)Adjust the heading direction of the
camera. Refer to Fehler! Verweisquelle
konnte nicht gefunden werden. for more
information.
9) To adjust zoom and focus, refer to 4.
Adjust Zoom and Focus for the
instructions.
Sealing gaps is recommended as gaps may appear after the camera
installation. Gaps may cause problems such as moisture, water leakage and
etc., which negatively affect the operation of the camera if gaps remain
unsealed.
To prevent products from damage, place the camera on a stable and non-
vibrating surface. If the stability is in doubt, consult safety personnel for
reinforcements, and then proceed with the installation.

G-Cam/E2 Series Installation
11
Installation of Ferrite Core
Installing the ferrite core is highly recommended to reduce high frequency
noise level.
The instructions and the image below explain how to install the ferrite core
on the cable.
1. Open the ferrite core by lifting the clip.
2. Make one loop with the cable through the ferrite core like the
enlarged square image below.
3. Close the ferrite core to hold the cable loop into place.

G-Cam/E2 Series Installation
12
4.1.2. Compatible accessories
- 5.02071: G-Cam/EBFC-002 (in-ceiling adapter for outdoor fixdome)
- 5.02072: G-Cam/EBWM-001 (Wall mount bracket for E2 EFD) in comb. with 5.02083,
G-Cam/ECMA-002 corner mount adapter or 5.02082, G-Cam/EPMA-004 Pole mount
adapter)
- 5.02080: G-Cam/EBWM-005 (Wall mount bracket for E2) with adapter 5.02085,
G-Cam/EBDA-200 only. The bracket also fits on 5.02090, G-Cam/EJBX-001 (E2
Junction Box) or on 5.02083, G-Cam/ECMA-002 (corner mount adapter) or on
5.02082, G-Cam/EPMA-004 (pole mount adapter), each with adapter 5.02085 (see
above)
- 5.02081: G-Cam/EBCE-003 (bracket ceiling extension) with adapter 5.02085, G- Cam/EBDA-200
only.
G-Cam/EBFC-002 G-Cam/EBWM-001 G-Cam/EBWM-005 G-Cam/EBCE-003
G-Cam-EBDA-200 G-Cam/EJBX-001 G-Cam/ECMA-002 G-Cam/EPMA-004

G-Cam/E2 Series Installation
13
4.2. Adjusting angle of the camera
1. Adjust the camera to the desired angle by unscrewing the joints referring to the following
pictures.
2. Insert the video output cable (included in the package) to the video output cable socket, and
connect it to an analogue video test monitor to check if the camera angle has been set as
intended. If the angle is appropriate, disconnect the camera from the analogue monitor, and
then remove the video output cable from the camera.
Adjust the joint to
install the camera on Adjust the joint to tilt
the camera angle.
Adjust the joint to
delicately
d
eo Out
Video output cable
socket

G-Cam/E2 Series Installation
14
4.3. Adjusting zoom and focus
To be able to adjust zoom and focus, it is necessary to connect the device to a network. Please
refer to 6.CONFIGURATION for the detailed method of network connection.
Once the device is on the network and the webpage is open, go to Setup> Video & Audio >
Zoom/Focus. Then, the features shown below will appear.
1. Adjust zoom and focus by clicking arrow buttons: the buttons move the lens more
extensively than the buttons .
2. Click One Click Focus to automatically set the lens focus.
3. If focus point is considered misaligned, reset it to a zero point by clicking Calibrate.

G-Cam/E2 Series Installation
15
4.4. Setting the Image Attributes
On the camera’s webpage, users can configure the image attributes. The menu of the image
attributes is available at “Video Appearance” via the path Setup > Video & Audio > Camera.
The following features can be adjusted: Brightness, Contrast, Saturation, and Sharpness.
For more detailed information, refer to the webpage user’s manual.

G-Cam/E2 Series Installation
16
5. CONNECTIONS
① Audio Connection
The camera provides a mono audio input and output. Due to low audio output power, an amplified
speaker is recommended for enhanced sound (Refrain from connecting a headphone or an
earphone directly to the camera).
- Microphone In: Max 2 Vp-p, 20KΩ (90dB)
- Loudspeaker Out: 60mW, 16Ω (95dB)
Mic
Amp Speaker
Out In
AUDIO
④
②
BLACK: AUD IN
BROWN: AUD GND
RED: AUD OUT
ORANGE: DI
YELLOW: DI COM
GREEN: DO1 (N.O)
BLUE: DO1 COM
①
⑤
③

G-Cam/E2 Series Installation
17
Sensor (DI) connection
Sensor (DI) can be connected to either a voltage type sensor or a relay type sensor.
Settings can be done through the camera’s webpage.
Input voltage range: 0VDC minimum to 5 VDC maximum, max. 50mA.
Do not exceed the maximum input voltage or relay rate.
② Alarm (DO) connection
Only the relay type is supported.
Relay Rating: Max 24 VDC 50mA
Do not exceed the maximum relay rating.
+3.3V
DI
COM
DI
COM +
-
Relay Type Voltage Type
+-
Output
of
Output
of
Internal Internal
+-

G-Cam/E2 Series Installation
18
③ LAN connection
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable (RJ45) to
connect the device to a hub or a router in the network. When the device is connected in network,
the orange LED blinks while green LED .
Refer to “Appendix (B) Power over Ethernet” for more information.
④ Power Connection
The camera can be powered by either 12 VDC or PoE+. If the camera is powered via PoE+, refer
to “Appendix (B) Power over Ethernet” for more information.
Green LED Orange LED

G-Cam/E2 Series Installation
19
6. CONFIGURATION
6.1. Set up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of the
device from converting the MAC address’s hexadecimal numbers, which is attached to the device.
Be sure that the device and PC are on a same area network before running the installation.
IP address: 192.168.xxx.xxx
Subnet mask: 255.255.0.0
Generic IP Environment
In case of generic private network environment where IP addresses 192.168.XXX.XXX are used,
users may view the live streaming images on a web page using the device’s default IP address:
1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal
Conversion chart at the end of the manual.
(The MAC address of the device is attached on the side or bottom of the device.)
„B1“ means: 1x 160 + 11x (B) 161 = 1 + 176 = 177.
„14“ means: 4x 160 + 1x 161 = 4 + 16 = 20.
2. Start the Microsoft® Internet Explorer web browser, and enter the IP address of the device.
3. Web streaming and device configurations are supported through ActiveX program. When the
ActiveX installation window appears, authorize and install the ActiveX.
MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177
Convert the last two sets of hexadecimal numbers to decimal num
b

G-Cam/E2 Series Installation
20
Custom IP Environment
IPAdminTool is a management tool, which automatically scans all network products for users to
perform administrative tasks, which includes network configurations, firmware update, device
reboot, and device organizations.
To modify the device’s default IP address for customized network area:
1. Find the device from the IPAdminTool’s list and highlight the device’s name.
2. Right-click the mouse, select IP Address. The IP Setup window appears.
3. Modify the last two digits of the device’s IP address, and modify the rest parts including subnet
mask, gateway, and DNS if necessary by checking the user / PC network area information.
4. Click on “Setup” to save the changes.
5. Later changes can be executed via Microsoft® Internet Explorer.
6. Streaming and configuration are realized with ActiveX. If you are asked for installation, apply
this.