GLITZHOME GH50110 User manual

Assembly Instruction
3 SHELF BOOKCASE

1
Explosive View
PRE-ASSEMBLY PREPARATION
• CAUTION: Assembly will require at least 2 adults. DO NOT use power tools.
Please inspect all items BEFORE assembly. If for any reason you need to return this item, please kindly
return it in it's original packaging.
• WARNING!
1. DO NOT let any sharp objects touch or rub the surface of the product.
2. When assembling, do not let children play around the working area.
3. DO NOT tighten all bolts and screws completely until the entire unit has been assembled and set up.
4. DO NOT USE if this product become damaged, and/or components are broken or missing.
•
MAINTENANCE:Please periodically check all fittings and re-tighten as necessary.
CARE AND CLEANING:DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.
Clean with mild soap on a soft rag. Rinse and dry thoroughly.
•
B
E
FF
F
F
D
C
C
C
A
A

2
PARTS LIST
SHELF PANEL (A) LEFT METAL FRAME (D)TOP PANEL (B) SHELF CROSS BAR (C)
Qty: 2 Qty: 1 Qty: 3 Qty: 1
REAR CROSS BAR (F)RIGHT METAL FRAME
(E)
Qty: 1 Qty: 4
Qty: 6
ALLEN BOLT (1) ALLEN BOLT (2) ALLEN BOLT (3) ALLEN BOLT (4)
Qty: 1 Qty: 6 Qty: 1
HARDWARE LIST
Qty: 1
PHILLIPS SCREW (5) NUT (6) ALLEN WRENCH (7) OPEN END WRENCH (8)
Qty: 4 Qty: 1 Qty: 1
Qty: 1 Qty: 1
L STEEL PLATE (9)
NOT INCLUDED
ANTI-TIPPING STRIP (10) WALL ANCHOR (11) SCREW (12)
Qty: 2 Qty: 1
M6*28mm
4mm
Ø8.5*30mm
M5*15mm
4*25mm
M6*22mm
M5
5*200mm
M6*12mm
4*12mm
11*11*24mm

3
C
C
C
C
C
C
2
2
2
2
4
6
2
2
EE
D
line up with the inside
These 4 holes must
be one side
Assemble shelf cross bar (C) to right metal frame (E) and left metal frame (D) with allen bolt (2)
using allen wrench (7).
STEP 1
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
6PCS2 ALLEN BOLT M6*22mm
1PC7 ALLEN WRENCH
Assemble all rear cross bars (F) together at one end with Allen bolts (4) and nut (6) using Allen
wrench (7)and Open end wrench (8). Fully tighten in this step.
STEP 2
F
F
F
F
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
1PC4 ALLEN BOLT M5*15MM
1PC6 NUT M5
1PC7 ALLEN WRENCH
1PC8 OPEN END WRENCH

4
Attach the remaining ends of the rear cross bars to the back side of the assembled shelves
with Phillips screws (5) . Fully tighten the screws by screwdriver (not included).
STEP 3
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
4PCS5
7
PHILLIPS SCREW 4*12mm
PHILLIPS SCREW DRIVER
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
6PCS
1PC
3ALLEN BOLT M6*30MM
ALLEN WRENCH
Not
included
Assemble top panel (B) & shelf panel (A) on ready metal frame with Allen bolts (3) by using
Allen wrench (7).
STEP 4
5
5
5
5
3
3
3
3
3
3
A
A
B
The hole on top panel (B)
should be on the bottom
and same side as x steel
wire (F).

5
Assemble steel plate (9) to top panel (B) with allen bolt (1) using Allen wrench (7).
STEP 5
Drill one hole on the wall and then put wall anchor (11) into the pre-drilled hole. Assemble steel
plate (9) to the wall with screw (12) using screwdriver. Attach anti-tipping strip (10) to the steel
plate (9) as shown.
STEP 6
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
1PC1 ALLEN BOLT M6*12MM
1PC9 STEEL PLATE
1PC7 ALLEN WRENCH
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
1PC9 STEEL PLATE
1PC10 ANTI-TIPPING STRIP
1PC
1PC
11
12
WALL ANCHOR Ø8.5*30MM
SCREW M4*25MM
9
B
1
10
NOT INCLUDED
WALL
11
NOT
INCLUDED
WALL
12
WALL 10 NOT INCLUDED
9
WALL

6
WALL
STEP 7