Grandview Large Stage MBII User manual

GRANDVIEW CRYSTAL SCREEN CO.LTD.
NO 43.S,Guomao Ave.Hualong,Panyu,Guangzhou,GuangDong.P.R.C
After sales service Tel:[phone]
Note :
When connecting to Rs232 or Rs485, if there is any motion that
cannot be controlled by the screen, please adjust the screen,
please adjust the two control lines;
Wiring loop resistance is less than 20Ω;
Do not run in parallel with strong interference sources;
232 port setting: 2400, n, 8, 1 A data string should be sent
twice consecutively.
Large Stage MBII Installation Manual
Model:LS-MBFxxxII(xGxx)
Intelligent RF control with external motor
Reminders
Thank you for purchasing Grandview products. Please read the instructions carefully before
installation and use, and collect it after reading for future use;
This product must be installed by a qualified professional after the feasibility assessment of
the environment, electricity, structure, etc.;
Do not disassemble or replace the original spare parts at will: If there is any fault, please
contact the after-sales service department.
Wireless control :
Press the up button, the screen will rise.
Press the stop button, the screen stop.
Press the down button, the screen down.
UP
DOWN
Wireless transmitter
Positioning Settings Key
Code pairing / deleting (factory pairing is successful):
Pay attention:
Long press the cycle button for 3 seconds, the screen is jogged once to enter the code-matching state; within 10 seconds, the
remote control up and stop buttons are also pressed, and the screen is jogged again to complete the code-matching; the code
deletion is the same as the code-matching operation, odd times The operation is code pairing; even code deletion.
To confirm the accuracy and security of the screen position, It is necessary to control the screen up and down after
adjusting every half turn of the button, Check if the position is moving correctly;
Be careful when adjusting the screen retracted height. Excessive adjustment will cause the lower rod to snap into
the casing and cause serious damage to the screen or the lower rod falling;
Be careful when adjusting the unfolding height of the screen. Always keep the fabric 1.5 turns or more around the
tube to ensure that the fabric does not fall;
Electrical parameters: Voltage Ac220 ~ 230V 50 /60Hz , Current 1.5A;
Wireless remote control (F): voltage 3V, using battery CR2032X2, transmission frequency; 868MHz, effective control
distance of about 15 meters;
Intelligent electronic stroke positioning (this product can set the up and down stroke of the fabric through the remote control)
Operation method:
Adjusting method of fabric retracting (upper limit) and upfolding (lower limit):
Upward stroke setting: Positioning setting key (light on) → Up key → Up and down remote control to the desired position →
Stop → Positioning setting key (light off) → Upward travel record success
If it is really necessary to adjust the limit height due to the installation environment or site limitation, you can use the motor
positioning adjustment key to rotate the knob on the motor limiter; the limiter adjustment knob is located in the 12 round hole
next to the power cord outlet.
Downstroke setting: Positioning setting key (light on) → Down arrow key → Remote control up and down to the desired position
→ Stop → Positioning setting key (light off) → Downstroke recorded successfully
Adjustment
hole
Power cable
Yellow button
Retracted height(lower limit)
Clockwise Down
Counterclockwise Up
Motor
White button
Unfolding height (upper limit)
Counterclockwise Down
Clockwise Up

Left hanging plate
Middle Hanging
plate
94
Rj45 port
S1 SW-PB
S2 SW-PB
S3 SW-PB
STOP
UP
DOWN
8P8C RS -232
P1
8
7
6
5
4
3
2
1
1
6
2
7
3
8
4
9
5
8 7 6 5 4 3 2 1
R 45
J
1
RS485-B
RS232-GND
2345678
RS485-A
RS232-TXD
Screen structure
Right Hanging plate
Casing
Accessories
Casing centerline
Fabric centerline
Fabric
Lower
rod
Motorized adjust tool (3)Shackle (3)
Screen hidden
installation location
Motor
exchange
port
Warranty Card (1)
Instruction manual (1)
Remote control (1)
Hook
Concrete ceiling
Note that due to structural reasons, the position of the fabric is not at the center of the screen. It's offset on the right by
about 94mm; This should be considered when determining the location of the mounting holes; It is also recommended to
keep a distance of 1 meter on the side of the screen power cord for future maintenance.
Measure the horizontal spacing of the hanging plate and the length of the product to determine the installation position
of the screen, and install three stable hooks on the solid concrete ceiling. Recommended hook type is adjustable.
Installation method and precautions
Suspension installation
Suspension distance(P)
remain distance
on the left
>1000mm
Hook the hook on the shackle of the left, middle and right hanging plate, adjust the length of the hook to the screen level,
and complete the suspension installaion
Note: The default factory setting of this product is suspension installation. If the customer needs screw rod installation, the
method of the hanging plate can be converted!
Screw rod installation
Converting the hanging plate method: Remove the M10 screws and 8 nuts on the left and right hanging plate, take out the
hanging plate and turnover to the corresponding end caps and fasten with screw.
Turnover
Measure the spacing of the four oblong holes on the left
and right hanging plate respectively. Install the M12 screw
rod directly above the corresponding hole to connect the
left and right hanging plate. Install an adjustable hook at
the top of the screen to connect the middle hanging plate.
Screw rod installation
Intelligent electric screen has 4 control methos:
A Manual control (cycle button)
B Wireless control
C Dry contact control
D Rs485 or Rs232 control
The manual control button is on the left end of the screen
casing (near the interface). This button is a circular control
button.
Screen control function description
Manual control STOP
STOP
Circular
UP DOWN
Power cable
Manual cycle button
Crystal head definition
Dry contact / Rs485 / Rs232 control
funciton
Connection
port line
number
stop up down Public
line
Public
line
Connection diagram
Data bits : 8
Start bits : 1
Stop bits : 1
Baud rate : 2400
UP : FFEEEEEEDD
STOP : FFEEEEEECC
DOWN : FFEEEEEEEE
Learn adress code instructions
FFXXXXXXAA
Some central controls need to
set the address code
FFEEEEEEAA
Rs485 / Rs232 port settings
Hex Control Code
USB Serial Port (COM3)
常规 端口设置 驱动程序 详细信息 事件
2400
8
无
位/秒(B):
数据位(D):
奇偶校验(P):
A
高级（ ）
…还原默认值(R)
1
无
停止位(S):
流控制(F):
取消
确定
Baud Rate: 2400
Data Bits: 8
Parity: none
Stop Bits: 1
Flow Control:
Baud Rate:
Baud Rate(B):
Data Bits(D):
Parity(P):
Stop Bits(S):
A
advanced（ ）
…Restore default(R)
取消
确定
none
Flow Control(F):
General Port Settings Driver Details Event
Load-
bearing Load- bearing
Anti-
dropping
Load-
bearing Load- bearing
Anti-
dropping