Grandview Elegant EL-M Series User manual

GRANDVIEW REPRODUCING GENUINE COLORS
Model EL-Mxx
GRANDVIEW REPRODUCING GENUINE COLORSGRANDVIEW REPRODUCING GENUINE COLORS
Thank you for purchasing a Grandview projection screen.
Before use, please read instructions carefully. After installation, store instructions for future reference.
Instruction Manual for
Elegant Series Motorized Screen
ISO9001:2000
International Certification
Grandview Crystal Screen Canada Ltd.
#11- 3751 North Fraser Way,
Marine Way Business Centre,
Burnaby, BC, Canada V5J 5G4
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.ca
Guangzhou Grandview Crystal Screen Co., Ltd.
P.O. 511400 Federal Ind. Zone No. 363, Yushan West Road,
Shiqiao, Panyu District, Guangzhou, Guangdong, China
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.com

1
Voltage VFrequency Hz Watts W
230V/120V/100V 50Hz/60Hz 90W/80W
230V/120V/100V 50Hz/60Hz 160W/156W
Metal Casing
End Cap
Screen Fabric
Rod
Description
Elegant Motorized Screen Power Specifications
Application
Applies up to 150" Elegant series
Applies to 180" and up Elegantseries
Instruction Manual (1pc )
C2 Mounting Bracketfor screen sizes
larger than 150" (2pcs )
C1 Mounting Bracketfor screen
sizes up to 150"( 2pcs )
Accessories
10 x 30 mmscrew and anchor (4pcs )
5 ( 1pc )Allen Key
Optional
5 40mm Tapping screw & cap ( 8sets )

2
5
Installation
Installation without bracket
AA
AA
2
3
45
This projection screen should be installed at the best possible viewing position for the audience.
Take out all the parts from the packaging and follow the accessories guideline to ensure you have
all parts. The parts needed will vary depending on which installation you choose to use. For
installation on a wood wall or ceiling, use the 5 x 40 screws. For installation on a drywall, use the
10 x 30 screws with anchors.
Wall Mount
Using a tape measure, measure the distance between the two keyholes on the casing ( Figure 1 ).
According to the measurement, use the drill to drill identical holes of the appropriate size (use a
smaller drill bit than the actual screws) on the wall and ensure that it is level ( Figure 2 and 3 ). Screw
in the appropriate screws, either the 5 x 40 for wood walls or the 10 x 30 plus anchors for drywalls,
leaving enough space at the end to hang the casing ( Figure 4 ). To ensure that the screen is level,
use a leveler to check ( Figure 5 ).
Ceiling Mount
Using a tape measure, measure the distance between the two rings for hanging on the casing
( Figure 1 ). According to the measurement, use the drill to drill identical holes of the appropriate
size (use a smaller drill bit than the actual hook screws) on the ceiling and ensure that it is level
( Figure 2 and 3 ). Screw in the hook screws (not provided), and lift the screen into the hooks
screws to hang ( Figure 4 ). To ensure that the screen is level, use a leveler to check ( Figure 5 ).
A
A
2
3
4
5
The ceiling or wall for fixture installation must be secure to prevent the screens from falling.
While installing electrical motors, please hire professionals or your local dealer toensure safety.
A misconnection may lead to fire or leaks.
Keep all infrared wireless products away from fluorescent lighting as it may cause malfunctions.
Please read the following as any damage to the screen surface will affect the quality of the picture:
1.Avoid contact or touching the screen surface as itmay cause scratches or tears.
2.Do not write or draw on the surface
3.Clean the screen with a soft cloth and luke warm water. Do not use any detergent or cleaning products.
Roll up the screen after every use. Ensure that the screen is level when installing; do not pull on the sides
or fold the screen.
To prevent unnecessary damage, the operating and maintenance of the screen should be done by adults.
used
Ignoring the safety warnings may
lead to injuries and/or damaging
the product.
Refrain from hanging anything on the
screen as it may cause the screen to
fall.
Do not connect any electrical
attachments or remote controls.
Fixtures should be installed in asecure
place to avoid accidents or thescreen
falling.
Roll up the screen after every use.
Leaving it hanging for a long period
of time may cause the fabricto loosen.
Please contact your local dealer for
repair s or maintenance. Please contact
our company if you have any further
questions. Avoid taking apart the
fixtures yourself. Loose parts may
cause the screen to fall.
Warnings
Do not take apart and replace with unknown parts. If there are any problems, please contact your local dealer.
Product specifications are subject to change.

34
Without mounting bracketinstallation
Wall mount
(Suitable for all sizes) Ceiling mount (Suitable for all sizes)
Hanger
Bracket Installation
To ensure extra durability and safety installation brackets have been included. The necessity of
brackets will vary depending on the location of installation. For installations of sizes up to 150",
use the C1 bracket. For installations of over 150", use C2.
Installation For Sizes Up to 150"
The screen can be installed either on the wall or with a hidden installation. The wall installation uses 2 holes
on the C1 brackets while the hidden installation uses all 3. Measure the distance between the holes that will
be used on the left and right brackets. Using the measured distance, drill the appropriate holes in the wall
( and ceiling if necessary ). Install the brackets, then lift and match up the screen's end caps to the brackets.
Insert the two screws to join the bracket and screen casing for both sides.
Installation For Sizes Over 150"
Using the C2 brackets, the screen can installed from the ceiling. Measure the distance between the holes
on the left and right brackets. Using the measured distance, drill the appropriate holes in the ceiling. Install
the brackets, then lift and match up the screen's end caps to the brackets. Insert the screws to join the
bracket and screen casing for both sides.
With mounting bracketinstallation( )Optional
Hidden installation
(Suitable for all sizes)
150 inches and under hidden
wall mount installation 150 inches and up installation
Instructions
Picture 1 Picture 2 Picture 3
2. Automaticremote control (Please see section on Remote Control)
Grandview projection screensare controlled by a manual switch or an automaticremote control.
1.Manual switch control
a. T
b.Connect to a power source (Please make sure it is the right voltage)
c. ; it will come down slowly. When it is all the way down, it
will stop automatically.
d. ; it will go up into the meta l casing. When it is all the way up,
it will sto p automatically.
e.To stop any time while the screen is in motion, turn the switch to 0.
ear off the glue cloth fixed on the bottom rod,ensure the bottom rod is not stuck by the casing.
Turn the switch to position 2 to lower the screen
Turn the switch to position 1 to retract the screen
Drop Limit
Retraction Limit
Attention:
> Please make sure there isno dust or dirt on the fabric surface before rolling it back to the casing
> The recommened working time is less than 50 seconds. The motor will enter overheating protection
status and stop working for everycontinuous 4 minuters operation, user would need to wait for a while
until the motor cool down beforeoperating again.
> There is no lube needed for the motor. Please be noticed that the appropriate setting is optimized which
requires no further adjustment, please consultthe after sales team before adjusting the limits.