Grandview SkyShow Series User manual

Integrated Motorized Screen
User Manual for SkyShow
Series Model D2
Suitable for Model Named SK-MFxxxD2
Protecting your Screen:
To ensure long lasting viewing enjoyment keep
the screen rolled up when not in use. Check both
the front and back surfaces before retracting into
the case to make sure it is free of dust, dirt, insects
or other foreign matter. Use a soft brush or cloth to
lightly remove any foreign particles.
Cleaning your Screen:
Use warm water with a mild detergent to remove
any marks on the surface or screen casing (only
dab, do not rub). Immediately dry the screen with
a soft cloth or towel. Do not leave it to air dry.
Never use any solvents, chemicals or abrasive
cleaners on the screen surface as they can
permanently damage the screen surface.
Guangzhou Grandview Crystal Screen CO., Ltd
No. 43 building, South national trade avenue, Hualong town,
Panyu district, Guangzhou City, Guangdong Province, CHINA.
For information please go to www.grandviewscreen.com or
call 86 (020) 84899499
Screen:Voltage AC220-230V/50/60HZ,1.5Amp,power 60watts.
RF remote(F):Voltage 3V,use CR2450*1 battery.
Radio Frequency:868Hz.maximum control distance 15m.
Setting for Up and Down Limited Positioning for Motor:
The limited positioning of motor has been defaulted when
EX-factory, it is not allowed to reset.
Note:
When setting RS232 or RS485, if the screen is not able to
operate as it is, please switch position of No.1 and No. 2.
The electric resistance of return circuit is less than 20Ω.
Do not do wiring nearby interference sources.
S1 SW-PB
S2 SW-PB
S3 SW-PB
STOP
UP
DOWN
8P8CRS -232
P1
8
7
6
5
4
3
2
1
1
6
2
7
3
8
4
9
5
1
RS485-B
RS232-GND
2345678
RS485-A
RS232-TXD
87654321
R 45
J
Dry Contact,RS485 & RS232 Wiring Map:
Line
FunctionSTOP UP DOWN COMMON
LINE
COMMON
LINE
RS485/RS232 control protocal:
connecting diagram
Baud Rate: 2400
Data Bits: 8
Stop Bits: 1
Parity: None
Hex command:
Screen UP: ff ee ee ee dd
Stop: ff ee ee ee cc
Down: ff ee ee ee ee
Learning address code instruction:
FFXXXXXXAA
(XXXXXX are hexadecimal
characters except E and 5)
Cancel address code instruction:
FFXXXXXXA6
USB Serial Port (COM3) Property
DetailEvent
Drive Program
GeneralPort
Confirm
AdvancedRestore
Baud Rate:2400
Data Bits:8
Parity:None
Stop Bits:1
Flow Control:None
Cancel
Caution:
Please remove all the stickers
before operate the screen.

CAUTION
Please prepare below necessary Installation tools: Screws
driver, leveling Instrument, tape measure and marker.
Installation preparation
Before installation, please measure the installation screws
distance and mark the screws position.
It must be assured the screen is fixed firmly onto the wall
which is strong enough according to the size and self weight.
After installation, keep the casing both edge level.
Dear Customers:
Thank you for the purchasing of Grandview Skyshow series D-
type projection screen. Before your normal using of product,
please read the specification first, and keep it well for future
reference.
Ceiling hanging Installation
Accessaries:
Motor Adjustment
tool(1pcs)
Remote
controller(1pc)
WARNING: Please guarantee ceiling or wall or
suspension device can bearing 4 times of product
net weight before installation
，otherwise people
hurt and property losses possible to happen by the
reason of screen falling.
WARNING: Installation position must strictly fit for
the dimension of product, to avoid problems like
product cannot be installed or install leaning.
Make sure that the hooks are installed rmly, connect the hanging
plates at the le and right ends of the screen to the hooks, and x
the screen to ensure that the screen will not accidentally slip o
the hooks under any circumstances. As shown:
Required Installation
distance
Hook
Concrete ceiling
It is recommended to use hook available with adjustable
length, please check below:
Ceiling hanging Installation
Mounting
bracket
According to the needs of the installation environment, the screen
shell can be hidden in the grooves on the wall and ceiling.
e installation method is the same as the suspension installation.
Recessed Installation
Power connection:
Grandview screen is pre-install with your local plug, you can
operate the screen easily when power supply is connected.
Important note:
This product is using Single-phase AC power supply, must well
connected to earth wire before operation.
Stop
Stop
Up Down
Cycle control
B. RF remote with model name :
Press Up button, screen retract
Press Stop button, screen stop
Press Down button, screen expand
RF remote is pre-setting in factory with
the screen, also can reset if necessary.
Electronic positioning by Remote
User could set the down limit with remote according to requirement.
Remote pairing:
1/Long press the cycle button for 3 seconds,the fabric jogs once and
enter into code pairing state.2/Press UP & STOP button together for 10
seconds. 3/the fabric joys and code pairing completed.
Remote un-pairing:
1/Long press the cycle button for 3 seconds,the fabric jogs once and enter
into code pairing state.2/Press UP & STOP button together for 10 seconds.
3/the fabric joys and code pairing cleared.
Up button
Down
button
Stop
button
Fabric control instruction
4 Control ways are available for integrated
motorized screen with model name of (SK-MI)
A. Manual control (cyclic key)
B. Wireless remote
C. LVC
D. RS485 or RS232
RF emitter for
model named
RJ45 port (used for
RS485 and dry contact
control)
power cable
Manual control key
A. Manual control:
Manual control button is on the left
side of the casing (close to RS485 and
dry contact interface), this is a cycle
control button.
Use a small pin fit to size to insert into positioning setting
keyhole at rear side of remote and press it to make the blue
light on.Then press “down”key on remote to operate screen to
go down.When screen moves to the required position, please
press positioning setting key with pin again to make screen
stop and the blue light would be also turned off.This is the
down positioning set as required. Please check below:
Note: Maximum travel distance of steel wire is 5meters.
Side(view) Front(view)Lower bar
Black
border
upper bar
Wire rope
Screen
shell
Motor/Circuit Board
Inspection Hole
Screen
fabric
Operation matters
It is forbidden for the screen wire rope to control the
screen up and down under the untensioned or unnatural
hanging state.