Grandview Sky-Show User manual

Grandview Sky-Show
User Manual
Imported and Distributed in Australia by
Herma Technologies
Factory 4A, 6 Albert St
Preston, VIC 3072
For more information please go to
www.grandviewscreens.com.au
or call 1300 730 025
Protecting Your Screen:
• Keepawayfromdirectsunlightor
 hightemperatures.
• Examineboththefrontandback 
 surfacesbeforeretractingintothe 
 casetomakesureitisfreeofdust, 
 dirt,insectsorotherforeignmatter.
• Useasoftbrushorclothtolightly 
 removeanyforeignparticles.
Cleaning Your Screen:
• Donotuseanysolvents,chemicals 
 orabrasivecleanersonthe
 screensurface.
• Useamilddetergentwithwarmwater 
 toremoveanymarksonthesurfaceor 
 screencase.
• Alwaysimmediatelydabthescreen 
 withasoftclothtoavoidsoapmarks.
• Donotscrubthesurface.
Warranty: 12 Months
RS 232/485 Input Settings / Close Contact
Back View
1
2
3
4
5
6
7
8
CrystalSocket
Control Emitter Function / Address
1Commonline 5CasingDown
2Retractingthescreen 6Stop
3Loweringthescreen 7Rs232InputB
4Casingup 8Rs232InputA
EXTERNAL CTRL
1
2
3
4
5
6
7
8
J1
8P8C
RS-232
P1
5
2
16
7
8
9
4
3
UP
S5
Stop
SW-PBS1
S4
S3
S2
SW-PB
SW-PB
SW-PB
SW-PB
Casing Down
Casing Up
ScreenDown
Screen Up
1. CentralControlFormatAgreementCommunication
AgreementSetting:databits:8bits,startbits:1bit,
stopbits:1bit,BaudRatio:2400.
2. Retractingthescreen:
oxFFoxEEoxEEoxEEoxDD
3. Stoppingthescreen:
oxFFoxEEoxEEoxEEoxCC
4. Loweringthescreen:
oxFFoxEEoxEEoxEEoxEE
5. Retractingthecasing:
oxFFoxEEoxEEoxEEoxC9
6. Loweringthecasing:
oxFFoxEEoxEEoxEEoxE9
7. 232setting:2400,n,8,1acontinuousdatasends
twotimes,eachtimeintervalof200ms.
Cable
Box
Ethernet Cable Box
Retractor
Central Control Input
GV_Sky_Show_Jun11_v1.2

Power Line
Secure
Positioning
Piece Casing
Secure
Positioning
Piece
Socket
Socket
Power Line
Secure
Positioning
Piece Casing
Secure
Positioning
Piece
Socket
Socket
To the Owner:
CongratulationsonpurchasingaGrandviewSky-Show.
Important Notes:
• Pleasereadthisinstructionmanualbeforeuse.
• Pleasedonotattempttoadjustorrepair
theproduct.Youwillvoidthewarranty.
• Pleaseretainthisinstructionmanualfor
futurereference.
• Handlethescreencarefullyduringtransportation.
•Toensurelonglastingviewingenjoyment,alwayskeep
thescreenrolledupwhennotinuse.
Warning
• Ensurethescreenishungbythelooped
suspensioncables.
• Thescreenmustbesecurelymountedbeforebeing
operated.Failuretocomplycancausethesuspension
cablestounravelresultinginthecablesbeingtangled
andpossiblescreendamageoccurring.
• Whensuspendingthescreenunderload-bearing
support,ensurethescreenishunglevel/straight.
• Damagecausedtotheproductduetoincorrect
installation,suspensionoroperationisnotcovered
bywarranty.
Operational Instructions
Mountthebreak
mechanismandscreen
asshownbelow.
Step 2Step 1
Ring
Hook
Brake Mechanism
Casing
Supplied
Cable BoxPower cord Multimedia
Cable Box
Cable Lock
Allen Key RF RemoteBrake Mechanism
Step 3
Insertthecableboxplugandattachbreakmechanism.
PlugthepowercordintotheCableBox.
Step 4
Cable
Box
Socket on
Cable Box
Ceiling
Plug Socket
Plug
Using RF Remote
Yourremotecontrolcomeswithbatteriesinstalled.
Tooperateyourremote:
Presstoliftthescreen
Presstostopthescreen
Presstolowerthescreen
TheMicroswitch
isusedforretractingor
loweringcable.
UP for screen fabric
Down for screen fabric
Down for cable
Up for cable
STOP for fabric & cable
Carefullyunpackthe
screen.Securelyattachthe
cableboxtotheceiling.
Screen Limit Settings
Thescreenisfittedwithtwolimits.Thelimits
automaticallystopthescreeninthefullyUp(toplimit)
andfullyDown(bottomlimit)positions.Youcanadjust
thebottomlimittosetyourviewingheight.
Setting The Bottom Limit
Caution:Settingthebottomlimitbeyondtheblack
leadermayrenderyourscreeninoperableandvoid
yourwarranty
Thebottomlimitswitchisaccessiblethrougha
grommetedholeatthebackoftheleftsidecasing.
Lowerthescreentotheoperatingpositionthen
insertthesuppliedAllenkeyintothewhitecoloured
screw.Turnitclockwisetoraisethescreenorturn
itanti-clockwisetolowerthescreen.
Whenloweringthebottomlimitthescreenwillmove
asyouadjustit.
Whenraisingthebottomlimitpleaseliftandlowerthe
screenwiththeremotetoseethenewposition.
Cable
Secure
positioning piece
Please secure your safety
limit lug at least 10mm
above the new limit
Up for cable
Down for cable
Cable Limit Settings
(The limits are preset at min 300mm and max 4950mm)
•Turntheremotecontrolovertolocatethe
“ProgrammingMode”activationtoggleswitch.
•PresswithafinetipandtheLEDshouldlightup,
indicating“ProgrammingMode”ison.
•Pressthemicro“UP/DOWN”buttonstomovethe
screencasetotherequiredposition.Pressthe
STOPbuttonwhenthedesiredlimitisachieved.
•PresstheProgrammingModetoggleswitchagainto
switchoffprogrammingmodeandsetthenewlimit.