Grandview GPCM-C User manual

3°
30°
3°
Instruction Manual
Projector Lift GPCM-C
Applicable Model: GPCM-C Series
Please read before using
Thank you for purchasing our products.
Ple ase r ead t he in str uct ion m anu al
carefully in order to ensure this projector lift
is suitable for your projection equipment.
Cautious
Warnings This instruction manual is written for dealers and technicians.
The customer must employ the technicians for installation. Please process the
construction following this instruction manual to avoid injury caused by accidents.
For safety, the minimum load of ceiling must be 40KG
Caution Please do not incline the
projector the extremely.
Please do not take apart the
accessories of projector lift.
Do not
take apart
M6-M8 Expanding
Screw or Tapping
Screw
Figure 6 Figure 7
Figure 8
Figure 9 Figure 10
Figure 12 Figure 13
Figure 11
A. Please install GPC support bar
assembly on the ceiling
Fix the base on the ceiling or concrete
(please ensure that the load is 40kg at least).
Figure 6
Open the back ornament board b, and
loosen the screws of subsidiary arm④
Please adjust the subsidiary arm④to your
desired position (this function is only for
B200、B300), and then fasten the screws
again. Please hide the power line into the gap
and close the back ornament board③b.
Figure 7 and Figure8.
③
.
C. Adjust your desired angle.
Loosen the screws of GPC support bar
assembly⑥
projector to your desired position and fasten
it. Figure 11
via the spanned; adjust the
1.
2. The direction of projector can be adjusted by
forward 30° and backward 3°. Left and
right adjustment is 3°.
Installation for multifunctional arm
(optional accessories)
Install the multifunctional arm on the
projector. Figure 12
Adjust the fixer a of multifunctional arm for
aligning the install hole of low bracket, and
then fasten the screws. Figure 13
Install ornament board⑩b for multifunctional
arm.
⑩
⑩
1.
2.
3.
For installing the completed low bracket to
the top bracket⑦that push up the completed
low bracket until it is fixed with the security
lock⑨and fasten the screws,refer to figure9
and figure 10.
Please ensure the GPC projector fixation is
fastened.
Connection of power cord to projector.
Install the back ornament board.
⑧
B.
assembly and GPM projector fixation
Please connect the GPC support bar
1.
2.
3.
4.
Grandview Crystal Screen Canada Ltd.
#11- 3751 North Fraser Way,
Marine Way Business Centre,
Burnaby, BC, Canada V5J 5G4
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.ca
Guangzhou Grandview Crystal Screen Co., Ltd.
No.43,Guomao Road South, Hualong Town,
Panyu District, Guangzhou City, China
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.com
www.grandviewscreen.com.cn

H
205mm
160mm
205mm
255mm
B C
3°
30°
3°
security holes
special
255mm
180mm
Top View
Diagram for applicable projector area
This projector lift must be installed above the bottom of projector (length 205mm; width 160mm).
Figure 1. Multifunctional arm is available for this projector lift and applicable projector area will be
increased (length 255mm; width 205mm)
Figure 1 Figure 2
Front View
Components and Accessories
GPCM-B is combined by GPC and GPM .
GPC
Assembly
The main bar and the subsidiary bar are fixed together from factory.Loosen
the screens of main bar③ and subsidiary bar④ . The distance between
projector and ceiling can be adjusted according to the distance of install holes
between main bar③ and subsidiary bar④ . Please refer to H in specification
table.
(Note: GPCM-C100 is no subsidiary bar and no stretch function).
③ ④
GPM
Assembly
1.GPM is combined by top bracket and low bracket . Press the
release button for separating the top bracket and low bracket.
2.There are special security holes for avoiding the falling of
projector (cooperate with security steel wire).
Usage
1. Press the release button for separating the top bracket⑦ and low
bracket⑧, refer to figure 3 and figure 4. Then, adjust the half-cycle
junction⑤ and ensure that the groove of half-cycle junction to be
align the direction of security lock⑨, and then put it on the
subsidiary bar after assembling. Finally, the glider is installed on the
half-cycle junction for fastening the main bar⑥ as the figure.
2. Connect the projector and low bracket. Figure 5
⑦ ⑧
Figure 3 Figure 4 Figure 5
Three steps for installation
A. Please install GPC support
bar assembly on the ceiling
B. Please connect the GPC
support bar assembly and
GPM projector fixation
C. Adjust your desired angle.
GPC
GPM
⑦
⑧
⑨
⑩⑩a ⑩b
①
②
③
③b
④
③a
④a
⑤
⑤b
⑥
Specifications
Adjust distance
for each grid
Optional Accessories
( )Support Bar、Multifunctional Arm
Product Name
400/600/800
30x355/30x295
Specifications
Model
Accessories
M4x10 Pressing Screw (4pcs)
M4x5 Pressing Screw (2pcs)
M4x5 Positioning Screw (2pcs)
M3x10 Cross Machine Screw(4pcs)
M4x10 Cross Machine Screw(4pcs)
M5x10 Cross Machine Screw(8pcs)
M5x30 Cross Machine Screw(4pcs)
M3x20 Cross Machine Screw(4pcs)
M4x20 Cross Machine Screw(4pcs)
M5x20 Cross Machine Screw(4pcs)
M3x30 Cross Machine Screw(4pcs)
M4x30 Cross Machine Screw(4pcs)
M5 Drop In Anchors(3 sets)
16x10 Rubber Insert(4pcs)
Washer(4pcs)
Spring Washer(4pcs)
Spanner (1pc)
Parts:
① Base (1pc)
② Ornament Cover (1pc)
③ Main Bar (1pc)
③a Front Ornament Board
③b Back Ornament Board
④ Subsidiary Bar(1pc)
④a Ornament board for
subsidiary bar
⑤ Half-Cycle Junction (1pc)
⑤b Glider (1pc)
⑥ Main Screw (1pc)
⑦ Top Bracket (1pc)
⑧ Low Bracket (1pc)
⑨ Security Lock (1pcs)
Optional Accessories:
Multifunctional Arm
⑩ Multifunctional Arm (2pcs)
⑩a Fixer (2pcs)
⑩b Ornament Board (8pcs) A