Grandview Prestige PP R1 Series User manual

GRANDVIEW CRYSTAL SCREEN CO., LTD.
No. 43 South International Trade Avenue, Hualong,
Panyu, Guangzhou, GuangDong, P.R.C
Tel: [phone]
User Manual for Prestige Series Fixed Frame Screen
Model: PP-xx (R1)
Maintainance
In order to maintain good performance of
screen, please cover the screen with cloth if it is
not used for a long term to prevent dust and dirt
from screen. If there are apparent varias or dirt
on screen material, please use soft brush or
cloth to clean it.
Clean the screen material
Rub gently according to grain of velvet frame
with warm water mixed with soft detergent.
(Please be noted that it should be gently rubbed
instead of scrubbing hard). Please prevent from
hitting the frame in case of damage of velvet. By
finishing cleaning, let frames dry itself.
Please do not use any dissolvent, chemical
agent or any tool with strong friction for clean,
which would cause permanent damage to the
screen.
Installation for screen:
Use tape to measure the overall length and height of
screen. Then apply the following formula to calculate
the distance of mounting brackets (please check be-
low). Finally align the mounting brackets horizontally
and vertically.
a：Horizontal distance: 0.6* overall length of screen
b：Vertical distance: overall height of screen minus 96mm.
Align horizontally
Align horizontally
a
b
Align vertically Align vertically
Slide the nut plates preinstalled in long black velvet
frame to align with mounting brackets. Then drive
tightly the Phillips screws with nut plates to finish instal-
lation of screen.
Slide the nut plate

Hook handle
Dear Customer:
Preparation for installation
Parts:
Long black velvet frame × 2 pcs
Long tension rod × 2 pcs
Short tension rod × 2 pcs
Screen material × 1 pcs
Mounting bracket × 4 pcs
Spring x some
Thanks for your purchasing Grandview product of
Prestige Series Fixed Frame Screen. Please go
through the user manual before use. Please keep
the user manual well for future reference.
Short black velvet frame × 2 pcs
Grub hexagon screw × 4 pcs
tapping screw × 8 pcs
expansion fixture × 8 pcs
Phillips screw × 8 pcs
P l e a s e pr e p a r e f o r s u i t a b l e t o o l s s u c h a s
gradienter, tape, marker, hexagon key, etc
Please make sure precise installation distance and
proper installation position for upper and nether
mounting brackets.
Use the proper screws for installation according to
the site. (use tapping screws for wooden wall and
tapping screws with expansion fixture for concrete
wall)
Instruction for installation
Assembly of frames:
Put the long and short frames on clean floor with
the rear side up to form a rectangle shape, please
see below:
Connect long frame with short frame by inserting locat-
ing pin on short frame into the hole on long frame. Then
insert grub hexagon screw to drive tightly with hexagon
key according to the order mentioned above.
Order to connect frames:①②③④
①②
③④
Accessory tool:
Hook handle × 1 pcs
Installation of screen material:
Tension rod
Face the screen material rear side up and lay it flat
on clean floor. Insert the tension rod from the tunnel of
screen material (advise to insert tension rod by two
people to avoid damage of fabric). Please check
below:
Lay flat screen material on the connected frame (both
of frame and screen material should face rear side up).
Hitch the tension rod with big ring of spring, then the
small ring on the other side to hitch slot of frame one by
one. It is advised to manage the springs on long frames
first (use the hook handle for assistance if needed).
Please check below:
After hitching all of springs with screen material, nec-
essary adjustment would be needed to make to assure
screen material has no wrinkles with well-distributed
tension.