Grandview LS-Zxx User manual

GRANDVIEW REPRODUCING GENUINE COLORS
GRANDVIEW REPRODUCING GENUINE COLORS
Thank you forpurchasing a Grandviewprojection screen.
Before use, pleaseread instructions carefully. Afterinstallation, keep instructionsfor future reference.
Model: LS-Zxx
Installation Guide for
Large stage series super mobile screen
ISO9001:2000
International Certification
Grandview Crystal Screen Canada Ltd.
#11- 3751 North Fraser Way,
Marine Way Business Centre,
Burnaby, BC, Canada V5J 5G4
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.ca
Guangzhou Grandview Crystal Screen Co., Ltd.
P.O. 511400 Federal Ind. Zone No. 363, Yushan West Road,
Shiqiao, Panyu District, Guangzhou, Guangdong, China
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.com

1
Legs ( 2pcs ) Tightening knobs
( 1pc )White screen ( )Gray screen Optional
Screen Frame
Support Bar
Leg
Extension
Screen
Description
Accessories
Screen Frame ( 1p c)
Fabric Package Bag ( 1pc )
Accessories List
32 mm x 32 mm
Model Sizes Application
Frame Specifications
Large-Stage Super Mobile series
Sizes and specificationsare subject tochange at anytime.
Applies up to 200" Large Stage Super Mobile screens
120 150 180 200
Unit
Specification(in)
Name
Screw Bar Pcs
Qty
12
100
Qty
14
Transportable Case
Instruction Manual ( 1pc )
Sizes and specificationsare subject tochange at anytime.

92
1.
-
Unpack and extendframe on a flat surface
(Figure 34).
This projection screen should be installedat the
best possible viewing position for theaudience.
Front projection ( Figure 1 )and Rear projection
( Figure 2 ). Install accordingto material chosen.
Installation
Figure 4
Figure 3
Figure 2
Figure 1
Please read the following as anydamage to the screen surface willaffect the quality of the picture:
1.Avoid contact or touching the screen surface as it may cause scratches or tears.
2.Do not write or drawon the surface
3.Clean the screen with asoft cloth and lukewarm water. Do not use any detergent or cleaning products.
To avoidinjury, two people are necessary for both assembly and storage.
Please use in a location shieldedfrom the elements, especially wind.A strong wind maycause the screen
to fall. All piecesof the frame and stand mustbe used together. The screen can be used separately.
To preventunnecessary damage, the operating and maintenanceof the screen should be done by adults.
Please fold up screen and returnall parts into the case afterevery use.
Warnings
Ignoring the safetywarnings may lea d to in juri es an d/or damaging the product.
Store back intotransporting case after use
Avoid conditions suchas wind and rain when used outside
Do not take apart and replace with unknown parts. If there are any problems, please contact your local dealer.
Product specifications are subject to change.

8
3
2.
Tosecure frame, "click" hinges into place
(Figure 5 - 6).
3.
Make sure 4corners are 90 degrees then
secure with support beams ( Figure 7 -9).
Figure 9
Figure 8Figure 7
Figure 6
Figure 5
Installation
"click"
Disassembly
11. Store firstly frame and legs on the bottom
layer of the freight case, fabricon top layer
( Figure 30 ).
Figure 30

4
7
4.
re
Unfold screen fabricand lay over frame
( Figu 10 - 11 ).
5. t
re
Snap screen buttonsto frame. Star at top
and finish atbottom (Figu 12 - 15).
Figure 10 Figure 11
Figure 12
Figure 13
Figure 14 Picture 15
Installation
1. Lay down the screen on flat ground ( Figure 24 ).
2. Take off screen from the frame by releasing
the buttons then fold ( Figure 25 ).
3. Screw off the black knobs and fold the legs
with releasing the locking system
( Figure 26 - 27 ).
4. Release the support beam onframe corners
( Figure 28 ) as wellas the locking buttons on
the frame, then fold the framefrom both
sides ( Figure 29 ).
Disassembly
Figure 24
Figure 25
Figure 26 Figure 27
Figure 28 Figure 29

56
6. reUnpack and extendlegs ( Figu 16 ).
7.
re
Set frame todesired height then extend legs
accordingly and fastenwith black knob
( Figu 17-19 ).
Installation
Figure 16
Figure 17
Figure 18
Figure 19
8. It's best to attach legs to frame on flatground.When
raising the screen, ensure Grandview logo and
double-sided snaps (for masking custom masking
-curtain) are on bottom ( Figure 20 - 21 ).
9. Pull downfront feet for stability ( Figure 22 - 23).
Installation
Figure 20
Figure 21
Figure 22
Figure 23