Grandview LS-MA III Series User manual

Model:LS-MAxxxIII(xSxx)
Reminders
Operation guidelines
How to use the remote control (optional) to control the power switch:
Adjusting method of screen retracted height (upper limit) and expanded height
(lower limit):
pay attention:
GRANDVIEW CRYSTAL SCREEN CO.,LTD.
NO.9 NO.10 NO.11
NO.7 NO.8
NO.6
UP
STOP
DOWN
Large Stage MAIII Installation Manual
Thank you for purchasing Grandview products. Please read the instructions carefully
before installation and use, and collect it after reading for future use;
This product must be installed by qualified professionals who evaluate the feasibility of
the environment, electricity, structure, etc;
Do not disassemble or replace the original spare parts at will: If there is any fault,
please contact the after-sales service department.
1.
2.
3.
Tear off the glue cloth fixed on the bottom rod, ensure the bottom rod is not stuck by the casing.
Connect to a power source (Please make sure it is the right voltage)
Turn the switch to position 2 to lower the screen; it will come down slowly . W h e n it is all the way
down,it will stop automatically.
Turn the switch to position 1 to lower the screen; it will go up into the metal casing. When it is all
the way up, it will stop automatically.
To stop any time while the screen is in motion, turn the switch to
This product comes standard with manual switch control. If you need to use the remote control, please
upgrade and install an external remote control kit (you need to cut off the manual switch and replace it
with an external remote control kit, see Figure 9-10). Please refer to the manual of the external remote
control kit for wiring method and instructions, and the size of the kit is shown in Figure 11.
The corresponding model of the external remote control kit is: external infrared remote control kit (2nd
generation), model: 1GD-IRAnII
External RF wireless remote control kit (2nd generation), model: 1GD-868MnII.
If you really need to adjust the limit height due to the limitations of the installation environment or site,
you can use the motor positioning adjustment key to rotate the knob on the motor limiter; just remove
the baffle on the power end to find the position of the motor.
In order to ensure the accuracy and safety of the screen position, the screen must be raised and lowered
every half circle of the button to check whether the position is moved correctly! Be especially careful
when adjusting the height of the screen recovery. Excessive adjustment will cause the lower rod to jam
into the shell and cause serious consequences such as damage to the screen or falling of the lower rod!
Be careful when adjusting the unfolding height of the curtain. Always keep the curtain wrapped around
the rotating tube with 1.5 turns or more to ensure that the curtain will not fall.
Electrical parameters: voltage AC220~230V/50-60Hz, current 1.5A.
A: No.43 S, Guomao Ave.Hualong,Panyu,Guangzhou,Guangdong,P.R.C
T: 020-84899499
White button
Yellow button
Unfolding height (upper limit)
Retracted height (lower limit)
Motor
Counterclockwise：Down
Clockwise： Up
Counterclockwise： Up
Clockwise ：Down
Disassembly
baffle

Screen structure
Left hanging plate Middle Hanging
Right Hanging plate
Casing
Fabric
lower bar unit：mm
Accessories
Weight bearing Weight
bearing
Anti-falling
Shackle(3) Warranty Card (1) Instruction manual (1)
Motor adjustment tool (1)
Concrete ceiling
suspension distance
Hook
Reserved on the left
>1000mm
Installation method and attention
Motor replacement method
Optional accessories
Screw fixed hanging
plate M8*30
Screw bolt Non-slip nut M8
Screen hidden installation location
Casing side view
205
102.5
16
38
260
222
≥80
≥80
≥200
Weight
bearing
Weight
bearing
Anti-
falling
≤200 ≤200
end cap
baffle
pull out the
motor bracket
Screw fixed hanging plate M10screw rod
205
106
10
50
50
(Note: Leave at least 1m away from the wall on the side of the power cord of the screen
for future maintenance)
Suspension Installation(standard configuration):
Measure the horizontal spacing of the hanging boards and the length of the product to
determine the installation position of the screen. Install a stable hook on a solid concrete
ceiling. It is recommended that the hook type be adjustable. (When the screen length is ≥
6m, 3 hangers are standard)
Hook the hooks on the shackles of the left, middle and right hanging plates respectively,
adjust the length of the hooks to the screen level, and complete the lifting;
(Note: the left and right hanging boards are the main stress points ,try to stay aside, and
the middle hanging boards are the secondary stress points)
Screw rod fixed hoisting (optional):
If the customer requires, you can purchase screw fixing hangers and accessories to fix the
screen; method: use M8 bolts and nuts to connect the screw fixing hangers to the outside
of the left and right hangers
Screw mounting: measure the distance between the four oblong holes on the left and
right hanging plates respectively, install M10 screw rods directly above the corresponding
holes to connect the left and right hanging plates, install an adjustable hook on the
middle of the screen to connect the middle hanging plate, and adjust the screws The
position of the screen to make the screen to a horizontal state, complete the installation
of the screen.
Before replacing the motor, retracted the
screen, fix the lower rod of the screen with
tape to prevent the rotating tube from
rotating freely, remove the end cap and
baffle at the end of the power cord, unscrew
the hexagon socket screw fixing the motor
bracket, and pull out the motor to replace it.
(Pay attention to the direction of the motor
adjusting hole facing downwards during
installation)