Grandview GPCN-E200 User manual

vertical tilt:±15°
The angle of
The nagle of
horizontal tilt:±8°
Rotation:360°
Instruction Manual
GRANDVIEW REPRODUCING GENUINE COLORS
Cautious
Warnings For safety, the minimum weight of ceiling must be 10KG
Caution Please do not incline the projector extremely.
Please do not take apart the accessories of projector
ceiling mount.
Do not
take apart
Projector Ceiling Mount
Applicable Model
GPCN-E200
GPCN-E3540
GPCN-E4560
Please read before using
Thank you for purchasing our
products. Please read the
instruction manual carefully
in order to ensure this
projector lift is suitable for
your projection equipment.
Details of installation
Height Adjustment
Adjust the main bar (2-1) to required height after taking apart the front
ornament board (2-3) and loosening the front positioning screw. And
then, re-install the front positioning screw and the front ornament
board (2-3), figure 11. (The height of GPCN-E200 can not be
adjusted )
figure 11
Angle Adjustment
1.Vertical adjustment: rotate the adjusting button (3-3) for vertical
angle, figure 12
2.Horizontal adjustment: rotate the adjusting button (3-2) for
horizontal angle, figure 13
3.Horizontal rotation adjustment: loosen the rotation adjusting screw
(3-4), the installation base can be rotated by 360°;fasten the rotation
adjusting screw (3-4) after deciding the angle,figure 14
figure 12 figure 13
figure 14
Installation of main bar
1.Firstly, please confirm how many installation holes the projector has?
3 or 4
2.If there are 3 holes, the installation arms (4-3) need to be taken apart
from Installation bracket firstly. Connect 3 installation arms(4-3) to the
projector, and then connect the installation arms (4-3) to the installation
base (4-6) However,the installation base needs to be the center of
projector. Figure 15.
3.Connect the installation arms to the projector conversely if the
distance of installation holes is less than 120mm. Connect the
installation arms (4-3) to the installation base (4-6) via sliding
installation button (4-3) as figure 16
4.Rotate the adjustable screw (4-4) for adjusting the height of instllation
arms (4-3) if the installation holes are not at the same level as figure 17
5.The front or back of adjuster must be parallel to the surface of
projector as figure 18
The front or back of
adjuster must be
parallel to the surface
of projector
figure 15
figure 16 figure 17
figure 18
Scope of
adjustment: 10mm
Grandview Crystal Screen
Canada Ltd.
#11- 3751 North Fraser Way,
Marine Way Business Centre,
Burnaby, BC, Canada V5J 5G4
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.ca
Guangzhou Grandview Crystal
Screen Co., Ltd.
No.43,Guomao Road South, Hualong Town,
Panyu District, Guangzhou City, China
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.com
www.grandviewscreen.com.cn

1-1
1-2
1-3
2-1
2-2
2-3
2-6
2-4
2-5
1
2
GPCN-E200 GPCN-E3540 GPCN-E4560
Perpendicular
to the ground
Parts
GPCN-E is combined by GPCN and GPE
GPCN Main Bar Overview
1-1 Top Cap
1-2 Fixation
1-3 Sliding Adjusting Hole
2-1 Main Bar
2-2 Subsidiary Bar
2-3 Front Ornament Board
2-4 Back Ornament Board of Main Bar
2-5 Back Ornament Board of Subsidiary Bar
2-6 Moving Button
GPE Adjusting Overview
3-1 Adjuster
3-2 Horizontal Adjusting
Button
3-3 Vertical Adjusting
Button
3-4 Rotation Adjusting
Screw
4-1 Installation Bracket
4-2 Installation Arm
4-3 Adjustable Screw
4-4 Sliding Installation
Button
4-5 Installation Base
Accessories:
① 6x50 Wood Screw (4pcs)
② M5x16 Philips Screw (6pcs)
③ M5x8 Philips Screw (6pcs)
④ M3x8 Philips Screw (4pcs)
⑤ M4x8 Philips Screw (4pcs)
⑥ M5x8 Philips Screw (4pcs)
⑦ 6x25 Tapping Screw (4pcs)
Scope for installation (Installation hole of projector):
Maximum scope for installation:390mm diameter
Minimum scope for installation:20mm diameter
Note: Connect the installation arms to the projector conversely for different installation
holes of projector.
Scope
Maximum diameter: 390mm Minimum diameter: 20mm
Scope for installation (H is the distance between ceiling and projector)
The H of GPCN-E200 is 250mm
The H of GPCN-E3540 is 350mm~400mm
The H of GPCN-E4560 is 450mm~600mm
Scope
Install the fixation on the ceiling (screws of accessory ① or ⑦) as
figure 1, and the fixation also can be installed on the ceiling which
angle is less than 15°as figure 2. GPCN-E can be installed to the
concrete-roof with ceiling or without ceiling, such as figure 3 and
figure 4.
figure 1
figure 2
figure 4figure 3
Steps of installation
Steps of installation
Connect the adjuster to GPCN Main Bar Overview, and then fasten
the screws (accessory ② ) as figure 5. Afterward, slide the
Adjustment Overview (projecter has been installed) to adjuster,
and the fasten the screws (accessory ③) as figure 6.Finally install
the top cap to the main bar, and then invaginate the spring. as
figure 7
figure 5
Details of installation
Wires collection
If the volume of power wire is less than diameter of main bar (2-1) that
please put this power cord inside the main bar directly. But if the volume
is greater than the diameter, please take apart back ormanent board
(2-4 and 2-5) and positioning button (2-6) from main bar (2-1)as
figure8. And then stay the power wire into the main bar (2-1)as figure 9.
Finally, re-install the back ornament board (2-4) from the other end,
and then install positioning button (2-6) and back ornament board (2-
5), figure 10.
figure 8 figure 9 figure 10
figure 6
4-1
4-2
4-3
4-4
4-5
3-4
3-1
3-2
3-3
H
H
H
figure 6
figure 7