Grange CONTARB User manual

To ensure longevity of your structure it is recommended that it is treated with a wood preservative on a yearly basis.
AFTERCARE
CONTEMPORARY
ARBOUR
CONTARB - 220cm [H] x 150cm [W] x 60cm [D]
220cm
60cm
CONTEMPORARY ARBOUR
PLAN
150cm
SIDE PANELS
ROOF BEAMS
ROOF SLATS
ARBOUR SEAT
SEAT BACK
A
B
C
D
E
A A
BC
E
D
Self-Assembly required Home Delivery available Pre-Painted available
www.grangefen.co.uk
All products and related emblems featured are
trademarks of Grange Fencing Ltd.
©2015 Grange Fencing Ltd All rights reserved.
In line with the Company’s policy of
continuous product development, the right
is reserved to change and improve product
design without prior notice.
CODE: CONTARB
ASSEMBLY
(cont.)
STEP 3
FITTING THE
ARBOUR SEAT
Add the Seat Sections. Your
Seat [D]should be
positioned approximately
45cm from the bottom.
Mark this position and join
the seat to the posts of the
two Side Sections [A]with
sixteen screws [x], four into
each post, front and back
through the wooden beams
underneath the seat.
Raise your Arbour into an
Upright position.
Finally fit the Seat Back [E]
bypositioning it on the rear
slat of the seat section [D]
and using four screws [x],
two per side, top and
bottom to fit it to the Side
Section posts.
Your Arbour is now ready
for use.
D
C
E
D
45cm
w
x
x
xx
x
x
xx
x
x
A
B
CONTARB (A5 4page instructions) 12/2/16 12:08 Page 1

BEFORE YOU START
When you are ready to start make sure you have the right tools to hand, plenty of space and a clean dry area for assembly.
It isadvisable for two people to carry out the work.
At each stage of construction ensure that the build is level and upright.
Drill pilotholes to aid assembly.
ARBOUR FOOTPRINT
Footprint of assembled arbour is
150cm x 60cm
Please check the packs and make sure that you have all of the parts listed above.
If not, contact your retailer who will be able to help you.
Thank you for choosing this garden product from Grange.
In order to gain the most benefit from it please read the following instructions carefully.
TOOLS REQUIRED (Not Supplied)
POWER DRILL/SCREWDRIVER
with posidrive No.2 bit
3mm DRILL FOR PILOT HOLES
STEPLADDER
WOODEN MALLET
PARTS LIST
SIDE PANELS
[146cm x 60cm] 2
CURVED ROOF BEAMS 2
ROOF SLATS STRIP 1
ARBOUR SEAT 1
SEAT BACK 1
HARDWARE PACK
SCREWS - 10cm 4
SCREWS - 7.5cm 20
SCREWS - 3.5cm 82
WOODEN DOWELS 8
A
[w]
[x]
[y]
[z]
ASSEMBLY
STEP 1
ASSEMBLING
THE ROOF SECTION
Take the two Curved Roof
Beams [B]and put them
side by side on the ground
approximately 60cm apart
with the grooved sides
facing each other.
Then unroll the Roof Slats
Strip [C]and lay this over
the top of the two roof
beams so that it fits snugly
into the grooves on each
side - see Fig.1
This can now be fixed to
the beams using the screws
[y], twoscrews per roof slat,
one either side.
Your roof section is now
assembled.
STEP 2
ASSEMBLING
THE ARBOUR
Lay the two Side Sections
[A]on the ground 150cm
apart and insert the eight
woodendowels [z], into the
holes at the top of each
post, tapping them firmly
into place with a wooden
mallet - see Fig.2
Then connect the Roof
Section to the Side Sections,
aligning the holes for the
dowels and gently pushing
into place. Finally, using the
four 10cm screws [w], one
per post, secure the Roof
Section to the Side Sections.
Do not lift the assembled
structure upright yet.
continued overleaf..
B
C
E
D
A
A
A
D
E
B
C
60cm
150cm
Fig.1
Fig.2
B
B
C
C
B
B
C
C
y
y
A
B
z
CONTARB (A5 4page instructions) 12/2/16 12:08 Page 2