Great Little Trading Abbeville L4406 User manual

1
Abbeville Storage - Long Shelf Unit
A few important pointers before you start:
• It might be worth checking on our website that there are no updates
or revisions to these instructions (if we have had helpful feedback from
other customers we pass it on via the product web page). Simply check
the date and version number on the front of this leaet against that of
any site updates.
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools. Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the
tools you need at the beginning of the instructions.
• It’s a good idea to build the unit in the room where you are going to be
using it, to avoid the need to move it after it’s been assembled.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
25/10/2017
V4
easy - medium - hard
Assembly Difculty
two-person job
Thank you for shopping with GLTC, we hope you enjoy having
this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail through
the whole process. But if it all feels a bit too much like hard work, then
we do have an assembly company we can recommend: the Flatpack
Construction Company offers a nationwide service and can be
contacted on 0843 289 4951 or www.atpackconstruction.co.uk.
Good luck!

2
Safety Warnings:
• Adult assembly required.
• Unassembled product contains small parts which may present a
choking hazard.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• Assemble and use on a at and level surface.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• To avoid possible injury from tipping, DO NOT allow children to climb
on this product.
• Always use the wall straps provided.
• Serious or fatal crushing injuries can occur from furniture tipping over.
Ensure you secure this furniture product to the wall before you use it
using the kit provided. If you have not received an anti-tip kit with your
product please contact Customer Services.
• Check all xtures and ttings regularly and tighten as necessary.
• Please retain these instructions for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [email protected]
Thank you

3
Component Check List Component Check List
#1 #2
#3
#5
#4
#6
14x Cam Locks
14mm Diameter
10x Barrel Nuts
18x Screws
17.5mmL
14x Cam Dowels
35mmL
24x Wooden Dowels
20mmL
10x Threaded Bolts
42mmL
1x Allen Key
Phillips Head Screwdriver
You will need (not supplied)
A B
C
E
G
I
D
F
H
1x Large Divider Panel
1x RH Side Panel
1x Base Panel
1x Upper Back Panel
1x Shelf Panel
2x Small Divider Panels
1x LH Side Panel
1x Top Panel
1x Lower Back Panel

4
STEP 1:
Take the shelf panel A and position it as shown, with the small pilot holes along the
edge facing upwards and the drill holes on the shelf itself facing down towards the
base of the unit. Insert 4x cam dowels (#1) as shown.
NOTE:
You will be building this unit face down. To make later steps easier and also to protect
the product during the building process, we suggest laying the polystyrene packing
down on the oor rst and building on top of it.
#1
#1
#1
#1
A
Hardware for Step 1:
4x #1 Cam Dowels
STEP 2:
Slot in the larger divider panel B, making sure the smaller drill holes are positioned at
the base end (the holes are visible on the other side of the panel).
A
B
TOP
BASE
TOP
BASE

5
TOP
BASE
STEP 3:
Position the two smaller divider panels C as shown, again ensuring that the smaller
holes are at the base of the unit.
When the panels are in place over the xed hardware and the wooden dowels, insert
cam locks into the large drill holes of the divider panels and turn clockwise to secure.
STEP 4:
Prepare both side panels.
C
4x #3 Wooden Dowels
Hardware for Step 3:
4x #2 Cam Locks
#2
#3
#3
E
#3
#3
#2
#2
#2
C
A
B
Hardware for Step 4:
4x #1 Cam Dowels
D
#1
#1
#1
#1
TOP
TOP
BASE
BASE

6
STEP 5:
Position the RH side panel D on the unit with the smaller drill holes positioned at the
base of the panel and the grooved edge facing upwards.
When the panel is in place over the xed hardware and the wooden dowels, (#3)
insert cam locks (#2) into the large drill holes of the shelf panel and turn clockwise to
secure.
STEP 6:
Position the LH side panel E on the unit with the smaller drill holes at the base of the
unit and the grooved edge facing upwards.
When the panel is in place over the xed hardware and the wooden dowels, (#3)
insert cam locks (#2) into the large drill holes of the shelf panel and turn clockwise to
secure.
E
2x #3 Wooden Dowels
Hardware for Step 5:
2x #2 Cam Locks
TOP
BASE
D
#2
#3
#3
#2
2x #3 Wooden Dowels
Hardware for Step 6:
2x #2 Cam Locks
TOP
BASE
#2
#3
#2
#3

7
STEP 7:
Attach the base panel F to the rest of the unit using wooden dowels, bolts and barrel
nuts as shown. Tighten the bolts using the Allen key provided.
Hardware for Step 7:
10x #5 Barrel Nuts
10x #4 Bolts Hardware for Step 8:
6x #1 Cam Dowels
STEP 8:
Prepare the top panel G.
G
#1
#1
#1
#1
#1
#1
TOP
BASE
TOP
BASE
#3
10x #3 Wooden Dowels
#4
#4
#4
#4
#4
#4 #4
#4
#4
#4
2x
#3
2x
#3
2x
#3
2x
#3
2x
#5
2x
#5
2x
#5
2x
#5
2x
#5
2x
F
E
D
NOTE:
This is where it helps building on the polystyrene
packaging.The unit will now be raised slightly making
it easier to attach the base & top panels without
having to lift up the part constructed unit.

8
STEP 9:
Position the top panel G onto the unit using the xed hardware and wooden dowels.
Once in place, insert 6x cam dowels into the larger holes on the side and divider
panels and turn clockwise to secure the top panel in place.
STEP 10:
Attach the back panels using the longer, thinner screws (#6). Please note that the
2x pilot holes indicated at the top of the unit are to attach anti-tip straps included
separately with this item.
Hardware for Step 10:
18x #6 17.5mmL Screws
H
6x #3 Wooden Dowels
Hardware for Step 9:
6x #2 Cam Locks
#2
I
#6
G
#3
2x
#3
2x
#3
2x
#2
#2
#2
#2
#2
D
E
BASE
TOP
BASE
TOP
#6
#6
#6
#6
#6
#6
#6
#6
#6
#6
#6
#6
#6
#6
#6
#6
F

9
Your unit is ready to use.
Attach the anti tip straps to the back of the unit using the remaining drill holes. For
details on securing the unit to the wall see the anti-tip kit guidance.
Copyright© 2016 G.L.T.C. Ltd.All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.