Great Little Trading L5240 User manual

1
Isla Dressing Table & Stool
L5240
21/12/2021
V3
Assembly Difculty
easy - medium - hard one person job
A few important pointers before you start:
• Please read the instructions right through before you start, and
check that all the components have been included in the pack;
we nd separating all the hardware into piles makes it easier to
be sure that everything is present and correct.
• Make sure you have the right tools.Allen keys are provided
if required, but screw drivers and other tools are not.You’ll
nd details of the tools you need at the beginning of the
instructions.
• It’s a good idea to build the unit in the room where you are
going to be using it, to avoid the need to move it after it’s been
assembled.
• Do not throw away any packing materials until assembly is
complete, just in case you accidentally discard smaller parts or
hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
GLTC Ltd, 12 Buckhold Road,Wandsworth, London, SW18 4GP, United Kingdom

2
Safety Warnings:
Dressing Table.
• Adult assembly required.Assembly to be carried out by a competent
adult only.
• Recommended for children 5 years+
• Not suitable for children under 3 years due to small parts which may
become detached and present a choking hazard.
• In an unassembled state product contains small parts which may pose a
choking hazard, not suitable for children under 3 years.
• During assembly children should be kept away from the product due to
possible risk of injury.
• Do not use this item if any components are missing or damaged.
• Assemble and use on a at and level surface.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• This product is heavy, we recommend that you build it where you are
planning to use it.
• Regularly check all xtures and ttings to ensure that they properly
tightened and tighten as necessary
IMPORTANT
READ CAREFULLY - KEEP FOR
FUTURE REFERENCE.
Safety Warnings:
Stool.
• This product has been designed, manufactured and tested to comply with
BS EN 17191:2021 seating for children.
• Adult assembly required.
• Unassembled product contains small parts which may present a choking
hazard.
• Assemble and use on a at and level surface.
• Children should be kept away from the product during assembly to avoid
any possible risk of injury.
• This product is suitable for children in the age range of 5 years plus.
• Maximum weight load 100Kg. Do not overload.
• DO NOT place this product near a window as it can be used as a step by
the child and cause the child to fall out of the window.
• DO NOT place this product near a window where cords from blinds or
curtains could strangle a child.
• Be aware of the risk of open res and other sources of strong heat in the
vicinity of the product.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• Check all xtures and ttings regularly and tighten as necessary.
• WARNING. Do not use this bed if any part becomes broken, torn or
missing. Please contact GLTC Customer Services on 0344 848 6000
immediately to arrange for suitable replacement parts.

3
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• The painted/lacquered surface is resistant to staining if cleaned
immediately, however please protect the surface from contact with
ball point pen and indelible style felt markers as the ink is by nature
permanent.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

4
A B
C D
E F
G H
I
K
J
1x Dressing Table Top 4x Dressing Table Legs
1x Drawer Support Panel
1x Drawer Side Panel
1x Drawer Base Panel
1x Drawer Front Panel 1x Stool Seat
4x Stool Legs
#1
#5
#7
#9 #10
#11
#13
#12
#3
#2
#6
#8
#4
16x Cross Head Bolts
(61mm)
16x Flat Washer
4x Barrel Nuts
4x Cross Head Bolts
(40mm)
2x L-Shaped Runners
(Left & Right)
2x Handles
2x Cross Head Bolt
(24mm)
8x Wooden Dowels
12x Screws
(14mm)
2x Flat Runners
(Left & Right)
16x Split Washer
8x Cam Dowels
8x Cam Locks
You will need
(not supplied)
Philips Head Screwdriver
1x Drawer Support Panel
1x Drawer Side Panel
1x Drawer Back Panel
Component Check List Hardware Check List

5
STEP 2:
Insert 4x cam dowels (#4) into the holes on the underside of panel A as shown.
Hardware for Step 1: Hardware for Step 2:
8x #3 Flat Washer
8x #2 Split Washer
8x #1 Cross Head Bolt (61mm) 4x #4 Cam Dowels
STEP 1:
Working on a protective surface such as a carpet or rug, take the dressing table
top (A) and lay it top down on the oor and prepare to attach the legs.
Prepare the hardware to attach the legs by taking 1x bolt (#1), thread on 1x split
washer (#2) followed by 1x at washer (#3). Prepare all remaining bolts this way.
You will use 8x on the dressing table and 8x on the stool.
Take one leg (B) and attach to the dressing table top using 2x of the pre-prepared
bolts/ washer sets.
Please note:When screwing in the pairs of bolts, for smoother insertion do not
screw one individual bolt all the way in, but instead alternate securing each of the
bolts until they are completely secure and as tight as they can possibly go.
Repeat with 3 remaining legs (B).
#1
#2
#3
#1
#1
#1
#1
#1
#1
#1
A
B
B
B
B
A
#4
#4
#4
#4
#4

6
STEP 4:
Take drawer support panel C and push onto the cam lock
hardware on the right-hand side of the desk top (when
facing).
The runner should be sitting at the top edge with the wheel at
the front of the unit.
When in place insert 2x cam locks (#7) into the large drill
holes on the panel and turn clockwise to secure.
Insert 2x barrel nuts (#8) into the smaller holes at the
back of panel C. Ensuring the holes are facing the back
panel.
Now, insert 2x 40mm cross head bolts (#9) through the
back panel of the dressing table top and into panel C.
Fully tighten both bolts.
STEP 3:
Attach the 2x at runners (#6) to drawer support panels (C & D).
The support panels and the runners have left and right versions, so please note the
positioning guidance to ensure the drawer closes correctly.
Take drawer support panel C and orientate as shown with drill holes facing up and
note the back end of the panel with drill holes in the short edge. Take a at runner
(#6) and position it so that the wheel of the runner is in the front corner of panel C
and the drill holes in the panel align with the holes in the runner. Insert 3x screws (#5)
into the holes in the runner as shown.
The wheel itself must be in the front corner. If it is not in the correct position or the holes do
not align, try the other runner.
REPEAT with drawer support panel D and note the front and back of the panels
are the other way around. Again, attach the runner so that the wheel is in the front
corner using 3x screws (#5).
Ensure the screws are fully inserted to ensure the drawer runs smoothly.
Hardware for Step 3:
2x #6 Flat Runners (Left & Right)
6x #5 Screws (14mm)
#6
#6
D
C
#5
#5
#5
#5
#5
#5
A
D
C
#9
#9
#9
#9
#8
#8
#8
#8
#7
#7
#7
#7
#7
#9
Hardware for Step 4:
4x #9 Cross Head Screws
(40mm)
4x #8 Barrel Nuts
4x #7 Cam Locks
FRONT
FRONT
BACK
BACK
(holes on panel edge)
(holes on panel edge)
Using Cam Locks:
When inserting into the panel,
ensure that each cam lock’s
arrow is pointing towards the
drill hole on the side edge of the
panel & the dowel that it will be
receiving.When the panels are
in the connected position, using
a screwdriver, turn the cam lock
in a clockwise direction to lock
and secure.
Repeat ALL of these steps with drawer
support panel D that should be
attached to the left-hand side of the
dressing table top (when facing).

7
STEP 5:
Take drawer side panels (E & F) and insert 1x cam dowel (#4) into the middle
hole at the end of BOTH panels, as shown.
Now take these panels and orientate so the small drill holes on the long edge
are facing up.
Take Panel E and position 1x L-shaped runner (#10) along the edge. The
wheel of the runner should be at the same end as the cam dowel hardware,
but the other side of the panel.
If the wheel is not positioned like this, try the other runner.
Now align the drill holes on the panel with the runner and insert 3x screws
(#5) in the holes shown to secure the runner.
Take panel F and REPEAT the runner attachment steps above ensuring the
wheel of the runner is at the same end as the cam lock but the other side of
the panel. Use the drill holes as shown.
Ensure the screws are fully inserted to ensure the drawer runs smoothly.
STEP 6:
Ta ke drawer side panel E and insert 2x wooden
dowels (#11) into the holes next to the cam
dowel.
Now join drawer side panel (E) with drawer
back panel (G) ensuring that the groove on the
inside of the drawer is aligned on both panels
and the large drill holes on panel G are facing
outwards.
Once joined, insert 1x cam lock (#7) into
the larger hole on back panel (G) and turn
clockwise to secure.
REPEAT this step using drawer side panel (F) at
the opposite end of back panel (G). Ensure the
groove is aligned with the other panels on the
inside of the drawer before securing.
Hardware for Step 5:
Hardware for Step 6:
6x #5 Screws (14mm)
2x #4 Cam Dowels
4x #11 Wooden Dowels
2x #10 L-Shaped Runners
(Left & Right)
2x #7 Cam Locks
#4
#4
#4
#7
#7
#7
#11
#11
#11
E
F
F
E
#5
#5
#5
#5
#10
#5
#5
#5
E
G
F#11
#11

8
STEP 7:
Slide drawer base panel (H) into the grooves on
the side panels (E & F), ensure it is pushed into
the groove on back panel (G).
Now take drawer front panel (I) and insert 2x
cam dowels (#4) into the central holes either
end of the panel as shown.
Now attach the 2x handles (#13) to panel I
using 2x cross head bolts (#12).
STEP 8:
Insert 4x wooden dowels (#11) into the
remaining holes on drawer front panel (I) and
then connect with the drawer box, ensuring the
groove aligns with the base panel (H).
Once in position, insert 2x cam locks (#7) into
the large drill holes in the drawer side panels and
turn clockwise to secure.
#11
#11
#11
#7
#7
#7
#12
#12
#12
#13 #13
#13
I
H
G
F
E
H
G
E
F
I
#4
#4
#4
#11
Hardware for Step 7: Hardware for Step 8:
2x #12 Cross Head Bolt (24mm)
2x #4 Cam Dowels 4x #11 Wooden Dowels
2x #13 Handles 2x #7 Cam Locks
#11

9
STEP 9:
Insert the completed drawer into the dressing table.
STEP 10:
Take one stool leg (K) and attach to the stool
seat using 2x of the pre-prepared bolts/ washer
sets (from step 1).
If you have not prepared the hardware, take a cross
head bolt (#1) and thread on a split washer (#2)
followed by a at washer (#3).
Please note:When screwing in the pairs of
bolts, for smoother insertion do not screw
one individual bolt all the way in, but instead
alternate securing each of the bolts until they
are completely secure and as tight as they can
possibly go.
Repeat with 3 remaining legs (K).
K
J
K
K
K
#1
#2
#3
Hardware for Step 10:
8x #3 Flat Washer
8x #1 Cross Head Bolt (61mm)
8x #2 Split Washer
Copyright© 2021 G.L.T.C. Ltd.All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.
Your dressing table and stool set are now complete.