Great Little Trading Blake User manual

1
Blake Cube Storage - 9 Cube Unit
08/12/2020
V1
two-person job
A few important pointers before you start:
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools.Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the tools
you need at the beginning of the instructions.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail
through the whole process. But if it all feels a bit too much
like hard work, then we do have an assembly company we
can recommend: the Flatpack Construction Company offers a
nationwide service and can be contacted on 0843 289 4951 or
www.atpackconstruction.co.uk.
Assembly Difculty
easy - medium - hard

2
Safety Warnings:
• PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
• Adult assembly required.
• CHOKING HAZARD - Unassembled product contains small parts
which may present a choking hazard to children under 3 years old.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• Assemble and use on a at and level surface.
• This product is heavy, so we recommend that you build it where you
are planning to use it.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• Cam dowels are used in the assembly of this unit.There is a natural
stopping point when turning, do not over-tighten.
• To avoid possible injury from tipping, DO NOT allow children to climb
on this product.
• Serious or fatal crushing injuries can occur from furniture tipping over.
• Ensure you secure this furniture product to the wall before you use it
using the kit provided. If you have not received an anti-tip kit with your
product please contact Customer Services.
• Always use the wall straps provided.
• Check all xtures and ttings regularly and tighten as necessary.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
A B
C D
E F
G H
I
K L
J
1x Base Panel 1x Side Panel
1x Side Panel
2x Vertical Dividers
1x Upper Back Panel
2x Side Skirting Bars
1x Lower Back Panel
2x Long Skirting Bars 4x Feet
#1 #2
#3 #4
#5 #6
#7
#9
#8
#10
28x Wooden Dowels (20mm) 22x Wood Screws (16mm)
16x Cam Locks 16x Cam Dowels
12x Wood Screws (25mm)
8x Barrel Nuts
8x Cross-Head Bolts (47mm)
4x Hex Bolt (42mm) 1x Anti-tip Kit
4x Wooden Dowels (25mm)
1x Allen key
You will need
(not supplied)
Philips Head Screwdriver
2x Horizontal Shelves
1x Top Panel
1x Mid Back Panel
Component Check List Hardware Check List

4
STEP 2:
Take both side panels B & C and insert 4x cam
dowels (#4) and 4x 20mm wooden dowels
(#1) into EACH panel as shown.
Hardware for Step 2:
8x #4 Cam Dowels
STEP 1:
Working on a protective surface like a carpet or rug, you will be building
this unit with the back facing up.
Take note of the panel orientation guidance in the steps.
With the help of a second person, take 2x horizontal shelf panels D
and hold in a parallel formation. Make sure the small drill holes on the
edges of the panels are facing up and the large drill holes on the faces are
pointing in the same direction to what will be the base of the unit.
Now slot 2x vertical divider panels E into the slots on panels D.
Orientate panels E with the smaller drill holes at the bottom short edge
of the panel in the same direction as the larger hardware holes on panels
D, which is towards the base.
#4
#4
#1
#1 #1
#1
8x #1 Wooden Dowels (20mm)
D
D
E
E
#4
#4
TOP
BASE
Note: The small drill holes
on the edges of panels D
should be facing up. #4
#4
#4
#4 #1
#1
#1
#1
C
B

5
Hardware for Step 4:
4x #3 Cam Locks
STEP 4:
Take side panel C and orientate so that the
grooved edge is facing up, the smaller drill
holes are at the base and the larger drill holes
are at the top of the panel.
Align the hardware on panel C with the holes
on the edges of both panels D and connect
to the unit as shown. When in place, insert
2x cam locks (#3) into the large drill holes of
BOTH the shelf panels D and turn clockwise
to secure.
B
C
#3
#3
#3
#3
#3
#3
Hardware for Step 3:
4x #3 Cam Locks
STEP 3:
Take side panel B and orientate so that the
grooved edge is facing up, the smaller drill holes
are at the base short edge and the larger drill
holes are at the top short edge of the panel.
Align the hardware on panel B with the holes
on the edges of both panels D and connect to
the unit as shown. When in place, insert 2x cam
locks (#3) into the large drill holes of BOTH the
shelf panels D and turn clockwise to secure.
#3
#3
#3
#3
D
D
B
TOP
TOP
BASE BASE
Using Cam Locks:
When inserting into the
panel, ensure that each cam
lock’s arrow is pointing
towards the drill hole on
the side edge of the panel
& the dowel that it will be
receiving.
When the panels are in the
connected position, using a
screwdriver, turn the cam
lock in a clockwise direction
to lock and secure.
D