Great Little Trading Alba Regular User manual

1
Alba Regular - Toy Box Base Unit & Top Shelf
L4469
easy - medium - hard
Assembly Difculty
one-person job
A few important pointers before you start:
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools.Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the tools
you need at the beginning of the instructions.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail
through the whole process. But if it all feels a bit too much
like hard work, then we do have an assembly company we
can recommend: the Flatpack Construction Company offers a
nationwide service and can be contacted on 0843 289 4951 or
www.atpackconstruction.co.uk.
05/06/2019
V1

2
Safety Warnings:
• Please read these instructions carefully before assembly.
• Warning! Not suitable for children under 3 years due to small parts
which may become detached and present a choking hazard.
• Assembly by a competent adult is required.
• Unassembled product contain small parts which may pose a choking
hazard to young children.
• During assembly children should be kept away from the product due
to possible risk of injury.
• Assemble and use on a at and level surface.
• This product is heavy, we recommend that you build it where you are
planning to use it.
• This unit can only be used in conjunction with other Alba Regular
units. All stacked Alba furniture must start with a GLTC Alba base unit.
• It is recommended that the Alba range is only stacked 3 units high
i.e. 1 x toy box base + top shelf & 2 x middle units.
• Ensure the drawer is opened & closed using the handle provided and
not by the top or side panel of the drawer to prevent hands being
squeezed as the drawer slides on its tracks.
• Do not over tighten hardware. Cam dowels should be inserted to
the collar. Back panel screws should be screwed until they naturally
tighten/stop. This is difcult to feel if power tools are being used.
• DO NOT use power tools in the assembly of this product as there is a
risk of over tightening and consequently splitting of the wood
• Do not use if any parts are missing or damaged as this may lead to
products being unstable.
• WARNING! FURNITURE TIPPING RISK. Serious or fatal crushing
injuries can occur from furniture tipping over. Ensure you secure this
furniture product to the wall before you use it, using the kit provided.
If you have not received an anti-tip kit with your product please
contact Customer Services.
• To avoid possible injury from tipping - DO NOT allow children to step
or climb on the product.
• Check all xtures and ttings regularly and tighten as necessary.
• Remove all packaging before allowing your child to use the product.
• Please retain for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
• Regularly check all fastenings, xtures and ttings to ensure that they
properly tightened.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
A B
C D
E F
G H
I
1x Top Shelf - Base
Component Check List Component Check List
J
K L
M N
1x Top Shelf - Back Upstand
1x Toy Box - Base Panel
1x Toy Box - LH Side Panel 1x Toy Box - RH Side Panel
1x Toy Box - Back Panel 1x Toy box Drawer - LH Side Panel
1x Toy Box Drawer - RH Side Panel 1x Toy Box Drawer - Back Panel
1x Toy Box Drawer - Base Panel 1x Toy Box Drawer - Front Panel
1x Top Shelf - LH Side Panel 1x Top Shelf - RH Side Panel
1x Toy Box - Top Panel

4
#1 #2
#3 #4
#5 #6
#7 #8
You will need
(not supplied)
Philips Head Screwdriver
#9 #10
#11
Component Check List
Hardware for Step 1:
STEP 1:
Build the Top Shelf rst.
Using a Phillips screwdriver, insert 1x cam dowel (#1) in the central hole of
panel A. Add 2x wooden dowels (#2) in the remaining holes and join panels A
& B together.
Insert 1x cam lock (#3) in the central hole of panel B and turn clockwise to
lock.
NOTE: The large drill holes on the panel A to be facing the oor and they
should be facing outwards on panel B.This will ensure they are not seen once
the unit is nished.
2x #2 Wooden Dowels
2x Flat Drawer Runners
(for Toy Box Surround)
2x Handles
2x L-Shaped Drawer Runners
(for drawer)
1x Anti- Tip Kit
19x Cam Dowels
35mmL
18x Wooden Dowels
25mmL
19x Cam Locks
15mmL dia
12x Domed Head Screws
14mmL
12x Flat Head Screws
14mmL
4x Flat Ended Screws
24mmL
4x Screws
30mmL
#3
#2
#2
#1
A
#2
#1
1x #1 Cam Dowels
1x #3 Cam Locks
IMPORTANT: Make sure that the
small drill holes on the edge of panel A
are next to the connection to panel B -
they will be needed at a later step.
#3
B
Using Cam Locks:
When inserting into the panel, ensure that each cam lock’s
arrow is pointing towards the drill hole on the side edge
of the panel & the dowel that it will be receiving.
When the panels are in the connected position, using a
screwdriver, turn the cam lock in a clockwise direction to
lock and secure.

5
STEP 2:
Using a Phillips screwdriver, prepare the top shelf side panels by inserting 3x
cam dowels (#1) into the smaller holes of BOTH panels D & C.
Hardware for Step 2:
STEP 3:
Insert 2x wooden dowels (#2) into the innermost holes on BOTH edges of
panel A. These will insert into the larger holes on panels C& D.
Attach the side panels and secure using 3x cam locks (#3) on BOTH sides.
NOTE: The shaped side of the side panels
to be facing up as shown.
#1
#1
#1
#1 x2
#1 x2 CD
6x #1 Cam Dowels
C
D
A
B
#3
#3
#3
#3
#3
#3
#2
#2
#2
#2
#3
#2
Hardware for Step 3:
4x #2 Wooden Dowels
6x #3 Cam Locks
Using Cam Locks:
When inserting into the panel, ensure that each cam lock’s
arrow is pointing towards the drill hole on the side edge
of the panel & the dowel that it will be receiving.
When the panels are in the connected position, using a
screwdriver, turn the cam lock in a clockwise direction to
lock and secure.

6
STEP 4:
Top Shelf is now ready for use.
STEP 5: Now build the Toy Box Surround.
Attach the at runners (#6) to the toy box side panels G & H using the at head
screws (#5).
The position of the runners is important.
- The wheel of the runner needs to be at the front of the panels (with the at edge) and close to
the straight edge of the panel (this is the base edge).
- Use the smaller holes when attaching the runner. Start with the rst small hole next to the wheel.
- The screws must be fully inserted and lie at on the runner to ensure the runner works smoothly.
When xed in the correct position, there will be a gap between the front edge of the panel and the
start of the runner. If the front of the runner is level with the edge of the panel, it is in the wrong
position.
G
H
#6
#5
#6
#6
#5
#5
#5
#5
#5
#5
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
Hardware for Step 5:
6x #5 Flat Head Screws 14mmL
8x #1 Cam Dowels
2x #6 Flat Runners
Then insert 4x cam dowels (#1) into the smaller holes in the four corners of
BOTH panels G & H.
FRONT
BACK

7
STEP 6:
Lay side panel G down and insert 4x wooden dowels (#2) into the holes in
the four corners of the panel.
Take base panel F (with the 2 ledges) and position under the runner. The
ledges/holes are to face outwards and the grooved edge is to line up with
groove on the side panel G.
Insert 2x cam locks (#3) and turn lock to secure the panels.
Then take top panel E and position on the long shaped edge of side panel G.
Ensure the large drill holes are facing inside the unit and the grooved edge is
lining up with the groove on panel G.
Insert 2x cam locks (#3) and lock to secure the panels.
STEP 7:
Insert 4x wooden dowels (#2) into the outer drill holes on the edges of
panels E & F.
Then take side panel H and position it as shown on top of the part assembled
unit, ensuring the grooved edge is lining up with the grooves on the other
panels.
Insert 4x cam locks (#3) into the remaining holes and lock to secure in place.
E
F
G
#3
#3
#3
#3
#2
#3
#2
#2
#2
#2
Hardware for Step 6:
4x #2 Wooden Dowels
4x #3 Cam Locks
Hardware for Step 7:
4x #2 Wooden Dowels
4x #3 Cam Locks #2
#3
#3
#3
#3
#3
#2
#2
#2
#2
H
G
E
F
Grooved edges on panels to line up
BASE
TOP
FRONT
BACK
BASE
TOP

8
STEP 8:
Line up the back panel I with the pilot holes in the grooved edges and x in
place with 12x domed head screws (#4).
The toy box surround is now ready to use.
Hardware for Step 8:
12x #4 Domed Head Screws 14mmL
STEP 9:
Make the toy box drawer.
Attach the L-shaped runners (#7) to the drawer side panels J & K with the at
head screws (#5).
The wheel of the runner should be on the opposite side of the panel to the
groove and should be next to two small recessed drill holes.
The runners should be the same length as the panels and the screws should
be at against the runner to ensure the drawer pulls out smoothly.
H
F
I
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4 #4
#4
#5
#7
#7
#7 #5
#5
#5
#5
#5
#5
JK
Hardware for Step 9:
6x #5 Flat Head Screws 14mmL
2x #7 L-Shaped runners

9
STEP 10:
Add the back panel L to the drawer sides.
Line up the grooves on the inside of the drawer and use a wooden dowel (#2)
to position the back panel L against the side panel J. Secure in place with 2x
screws (#10). The screws should sit inside the recessed holes and should not
protrude.
Repeat on the other side with panel K, again lining up the grooves on the
inside and securing with 2x screws #10.
STEP 11:
Slide base panel M into the grooves on the inside of the drawer box.
J
L
K
#10
#10
#10
#10
#2
#2
#2
#10
Hardware for Step 10:
2x #2 Wooden Dowels
4x #10 Screws 30mmL
J
L
K
M

10
STEP 12:
Take drawer front panel N and attach 2x handles (#8) using 4x at ended
screws (#9).
Insert 4x cam dowels (#1) into the outer holes on the panel.
#8
#8
#8
#9
#9
#9
#9
#9
#9
#1
#1
#1
#1
#1
N
Hardware for Step 12:
4x #1 Cam Dowels
4x #9 Flat End Screw 24mmL
2x #8 Handles
STEP 13:
Insert 2x wooden dowels into the remaining middle holes on the front panel
N.
Line up the groove on the drawer front with the base panel of the drawer box
and push into position on the drawer box. Insert 4x cam locks into the holes
on panels J & K and lock to secure.
#2
#2
#2
#3
#3
#3
#3
#3
N
M
K
J
L
Hardware for Step 13:
2x #2 Wooden Dowels
4x #3 Cam Locks