Great Little Trading L5124 User manual

1
Blake Cube Storage - Bench
L5124, L5125.
17/12/2021
V3
Assembly Difculty
one-person job
easy - medium - hard
A few important pointers before you start:
• Please read the instructions right through before you start, and
check that all the components have been included in the pack;
we nd separating all the hardware into piles makes it easier to
be sure that everything is present and correct.
• Make sure you have the right tools.Allen keys are provided
if required, but screw drivers and other tools are not.You’ll
nd details of the tools you need at the beginning of the
instructions.
• It’s a good idea to build the unit in the room where you are
going to be using it, to avoid the need to move it after it’s been
assembled.
• Do not throw away any packing materials until assembly is
complete, just in case you accidentally discard smaller parts or
hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
GLTC Ltd, 12 Buckhold Road,Wandsworth, London, SW18 4GP, United Kingdom

2
SAFETY WARNINGS!
• This product has been designed, manufactured and tested to comply with
BS EN 17191:2021 seating for children.
• Adult assembly required.
• Unassembled product contains small parts which may present a choking
hazard.
• Assemble and use on a at and level surface.
• Children should be kept away from the product during assembly to avoid
any possible risk of injury.
• This product is suitable for children in the age range of 3 years plus.
• Maximum weight load 100Kg. Do not overload.
• DO NOT place this product near a window as it can be used as a step by
the child and cause the child to fall out of the window.
• DO NOT place this product near a window where cords from blinds or
curtains could strangle a child.
• Be aware of the risk of open res and other sources of strong heat in the
vicinity of the product.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• Check all xtures and ttings regularly and tighten as necessary.
• WARNING. Do not use this bed if any part becomes broken, torn or
missing. Please contact GLTC Customer Services on 0344 848 6000
immediately to arrange for suitable replacement parts.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you
IMPORTANT
READ CAREFULLY - KEEP FOR
FUTURE REFERENCE.

3
A B
C D
E F
G H
I
K
J
1x Side Panel 1x Side Panel
1x Base Panel
1x Back Panel
2x Support Bars
2x Vertical Dividers
2x Long Skirting Bars
3x Shelves (optional)
4x Feet
#1 #2
#3 #4
#5 #6
#7
#9
#11
#8
#10
#12
6x Wood Screws (18mm) 20x Wooden Dowels
8x Cam Dowels 8x Cam Locks
12x Wood Screws (25mm) 8x Cross-Head Bolts (47mm)
8x Barrel Nuts
4x Wooden Dowels (25mm)
1x Allen Key
12x Shelf Pegs
4x Hex Bolts (42mm)
12x Back Panel Screws
You will need
(not supplied)
Philips Head Screwdriver
1x Top Panel
2x Side Skirting Bars
Component Check List Hardware Check List

4
Hardware for Step 2:
4x #2 Wooden Dowels
STEP 2:
Prepare the top panel D by inserting 4x cam dowels (#3) and 4x 20mm
wooden dowels (#2) into the holes as shown.
STEP 3:
Orientate top panel D so that the grooved edge is on the oor.
Take both vertical divider panels E and connect to top panel D along the edge
with the larger drill holes as shown.
When in place, insert 2x cam locks (#4) into the large holes on BOTH panels
E and turn clockwise to secure.
4x #3 Cam Dowels
Hardware for Step 3:
4x #4 Cam Locks
#4
#4
Hardware for Step 1:
6x #1 Wood Screws (18mm)
STEP 1:
Working on a protective surface like a carpet or rug, position both side
panels A & B with drill holes facing up.
Using a phillips screwdriver, insert 2x cam dowels (#3) into the holes in the
corners of BOTH panels, then insert 2x 20mm wooden dowels (#2) into
the holes next to them.
Now take 2x support bars C and attach them to panels A & B using 3x
18mm wood screws (#1) on EACH bar.
#1 #1 #1
#1 #1 #1
#2 #2
#2 #2
4x #2 Wooden Dowels
4x #3 Cam Dowels
A
C
C
BD
D
#3 #3
#3 #3
#3
#3
#3
#3
#2
#2
#2
#2
E
E
#4 #4
Using Cam Locks:
When inserting into the
panel, ensure that each cam
lock’s arrow is pointing
towards the drill hole on
the side edge of the panel
& the dowel that it will be
receiving.
When the panels are in the
connected position, using a
screwdriver, turn the cam
lock in a clockwise direction
to lock and secure.

5
STEP 6:
Now attach the 2x long skirting bars H to the edges of base panel F.
Position them rst using 4x 20mm wooden dowels (#2). Then x the bars in
place with 8x 25mm wood screws (#5).
Again the recessed holes should be facing up to hide the hardware once inserted.
STEP 7:
Turn base panel F over and insert 8x 20mm wooden
dowels (#2) into the inner holes of each pair as
shown below.
STEP 4:
Now take both side panels (A & B) and insert the hardware into the open ends
of top panel D.
Ensure the grooved edges of the side panels are on the oor.
Insert 4x cam dowels (#4) into the large drill holes on panel D and turn
clockwise to secure the side panels in place.
Hardware for Step 5:
4x #5 Wood Screws (25mm)
STEP 5:
Take Base Panel F and orientate with the multi-drilled side shown here facing
up.
Take the 2x side skirting bars G and using the holes shown, attach to base
panel F with 4x 25mm wood screws.
The recessed holes on the bars should be facing up to hide the hardware
once inserted.
Hardware for Step 4:
4x #4 Cam Locks
#4
#5
#5
#5
#4
#4
#4
BD
A
EE
F
G
G
#5
H
H
F
#2
#2
#2
#2
#2
#2
#2
#2
#5 #5
#5
#5
#5
#5
#5
#5
Hardware for Step 6:
Hardware for Step 7:
8x #5 Wood Screws (25mm)
4x #2 Wooden Dowels
8x #2 Wooden Dowels
F
#2
#2
#2
#2

6
STEP 8:
Return to the bench frame and insert 8x
barrel nuts (#7) into the holes on the sides of
panels A, B & both Es. Ensure the hole in the
barrel nut is facing the edge of the panels.
With the grooved edge of the base panel F on
the oor, position the panel onto the bench
frame using the wooden dowels.When in
place, insert 8x cross-head bolts (#6) through
the base and into the barrel nuts. Fully tighten
all bolts.
STEP 9:
Attach the feet.
Use 1x 25mm wooden dowel (#9) to position
1x foot (K) on any corner of the base, then
insert 1x hex bolt (#8) through the base panel
to secure.
Fully tighten using the allen key (#12) supplied.
Repeat on remaining 3 feet.
STEP 10:
Carefully stand the unit onto its feet and insert
back panel J into the grooved edges and secure
using 12x back panels screws (#10).
Note the lower edge of the back panel has the
notches on both sides.
#6
#6
#6
#6
#7
#7 #7 #7
#8
#9
#9
#9
#10
#7
#6
#6
#6
#6
Hardware for Step 8: Hardware for Step 9:
Hardware for Step 10:
8x #7 Barrel Nuts 4x #9 Wooden Dowels (25mm)
8x #6 Cross-Head Bolts (47mm) 4x #8 Hex Bolts (42mm)
12x #10 Back Panel Screws
K
K
K
K
#9
#8
J
#10
#10
#10
#10
#10 #10
#10
#10
#10
#10
#10
F
B
E
E
A

7
Copyright© 2021 G.L.T.C. Ltd.All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.
STEP 11:
If you are using the optional shelves (I) in some
or all of the storage areas of the bench, insert
4x shelf pegs (#11) into the holes on the inside
of the spaces you wish to shelve.Then place the
shelf on top of the pegs.
Your product is now ready to use.
I
I
I
#11
#11
#11
4x
4x
4x
Hardware for Step 11:
12x #11 Shelf Pegs