Great Little Trading Alba L4467 User manual

1
Alba Regular - Two Door Cupboard Unit
L4467
easy - medium - hard
Assembly Difculty
two-person job
A few important pointers before you start:
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools.Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the tools
you need at the beginning of the instructions.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail
through the whole process. But if it all feels a bit too much
like hard work, then we do have an assembly company we
can recommend: the Flatpack Construction Company offers a
nationwide service and can be contacted on 0843 289 4951 or
www.atpackconstruction.co.uk.
30/08/2019
V2

2
Safety Warnings:
Please read these instructions carefully before assembly.
• Warning! Not suitable for children under 3 years due to small parts
which may become detached and present a choking hazard.
• Assembly by a competent adult is required.
• Unassembled product contain small parts which may pose a choking
hazard to young children.
• During assembly children should be kept away from the product due
to possible risk of injury.
• Assemble and use on a at and level surface.
• This product is heavy, we recommend that you build it where you are
planning to use it.
• This unit must be used in conjunction with Alba Regular Base + Top
Shelf unit.All stacked furniture combinations must start with a GLTC
Alba base unit.
• It is recommended that the Alba range is only stacked 3 units high i.e.
1 x toy box base + top shelf & 2 x middle units OR 1x tall base unit &
1x middle unit.
• Ensure the doors are opened & closed using the handle provided.
• Do not use if any parts are missing or damaged as this may lead to
products being unstable.
• DO NOT use power tools in the assembly of this product as there is a
risk of over tightening and consequently splitting of the wood.
• Do not over tighten hardware. Cam dowels should be inserted to
the collar. Back panel screws should be screwed until they naturally
tighten/stop. This is difcult to feel if power tools are being used.
• WARNING! FURNITURE TIPPING RISK. Serious or fatal crushing
injuries can occur from furniture tipping over. Ensure you secure this
furniture product to the wall before you use it, using the kit provided
in the BASE unit.
• To avoid possible injury from tipping - DO NOT allow children to step
or climb on the product.
• Check all xtures and ttings regularly and tighten as necessary.
• Remove all packaging before allowing your child to use the product.
• Please retain for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
• Regularly check all fastenings, xtures and ttings to ensure that they
properly tightened.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
A B
C D
EF
1x Side Panel
Component Check List Component Check List
1x Side Panel
1x Top Panel 1x Base Panel
1x Central Divider 2x Back Panels
1x Door 1x Door
G H
I
2x Shelf Panels
#1 #2
#3 #4
#5 #6
You will need
(not supplied)
Philips Head Screwdriver
#7 #8
#9 #10
8x Cam Dowels
35mmL
8x Cam Locks
15mm dia
12x Wooden Dowels
25mmL
14x Domed Head Screws
14mmL
30x Flat Head Screws
14mmL
4x Hinges
2x Magnetic Catches
2x Handles
4x Flat Ended Screw
24mmL 2x Keeper Plates
8x Shelf Supports
16mmL
#11

4
Hardware for Step 1:
STEP 1:
Prepare the side panels.
Using a Phillips Screwdriver, insert 4x cam dowels into the four holes on the
corners of BOTH side panels A & B.
8x #1 Cam Dowels
A
B
#1
STEP 2:
Add 2x magnetic catches (#6) to the front edge of the top panel C using 4x
at head screws (#5).
Position the screw in the middle of the slot on the magnetic catches.
NOTE: If, once the unit is complete, the doors are standing proud from the
unit, move the magnetic catches back a little.
Hardware for Step 2:
4x #5 Flat Head Screws
2x #6 Magnetic Catches
C
#5
#5
x2
x2
#6
#6
#6
#5
#5
#1
#1
#1
#1
#1
#1
#1
#1

5
STEP 3:
You are building this unit BACK up.
Take top panel C and insert 2x wooden dowels (#2) into the central holes and
connect to the top edge of panel E. Panel E should have the drill holes closer
to the edge of the panel upper most.
The grooved edge of panel C should be facing up and the large drill holes
should be facing inside the unit.
Then take panel D and insert 2x wooden dowels (#2) into the central holes
and connect the lower edge of panel E.
Again, the grooved edge of this panel should be facing up, but this time the
large drill holes should be facing outwards.
Hardware for Step 3:
4x #2 Wooden Dowels
STEP 4:
Take side panel B and insert 4x wooden dowels into the
remaining holes.
Position the panel with the grooved edge facing up and
the top edge with the shaped notch by the magnetic catch.
Push onto the edges of panels C & D.
Insert 4x cam locks into the large drill holes on panels C &
D and turn clockwise to lock.
C
E
D
#2
#2
#2
#2
#2
C
E
D
B
#2
#2
#3
#3
Hardware for Step 4:
4x #2 Wooden Dowels
4x #3 Cam Locks
BASE
TOP
TOP
BASE
Using Cam Locks:
When inserting into the panel, ensure
that each cam lock’s arrow is pointing
towards the drill hole on the side
edge of the panel & the dowel that it
will be receiving.
When the panels are in the connected
position, using a screwdriver, turn the
cam lock in a clockwise direction to
lock and secure.
#2
#2
#2
#3
#3
#3
Holes closest to the edge of
panel E to be upper most.

6
STEP 5:
Repeat step 4 with side panel A .
STEP 6:
Position both back panels F as shown with the angled edges in the corners of
the unit.
Line up the panels with the pilot holes in the grooved edges and x in place
with 14x domed head screws (#4).
When complete, please turn the unit onto it’s side, so you are ready to attach
the doors.
Hardware for Step 5:
4x #2 Wooden Dowels
4x #3 Cam Locks
A
#2
#2
#2
#2
#3
#3
#3
#3
#3
F
F
#4
Hardware for Step 6:
14x #4 Domed Head Screws
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4
A
D

7
STEP 7:
Attach the handles (#8) to the door panels G & H using 4x at ended screws
(#9).
Attach the keeper plates (#10) to EACH door using 2x at head screws (#5)
Then with the hinges (#7) in the open position, insert them into the large
holes on the door panels.
Fix in place with 8x at heads screws (#5)
STEP 8:
IMPORTANT: Two people are needed to complete the next step safely.
Position door G as shown so that the hinge plates on both hinges line up with
the pilot holes on the side panel.
Fix EACH hinge in place with 4x at head screws (#5).
It is best to leave the screws slightly loose to allow for aligning the hinges
once in position.
Hardware for Step 7:
10x #5 Flat Head Screws
4x #9 Flat Ended Screws
Hardware for Step 8:
8x #5 Flat Head Screws
G
H
#8
#8 #8
#9
#9 #9
x2 x2
#10
#5
#5 x2 #5 x2
#7 #7
2x #8 Handles
4x #7 Hinges
2x #10 Keeper Plate
G
#5 x4
#5 x4
#5 x4
Note: Keeper plate on door to
be at the same end of unit as
the magnetic catches (top).
TOP
BASE

8
STEP 9:
IMPORTANT: Two people are needed to complete the next step safely.
Carefully turn the unit over so it is on it’s other side.
Repeat Step 8 with door H.
Again, it is best to leave the screws slightly loose to allow for aligning the
hinges once in position.
Please turn the unit up the right way.
STEP 10:
Insert the 4x shelf supports (#11) at the desired shelf level in each side of the
cupboard unit.
Insert shelf panels I.
Hardware for Step 10:
8x #11 Shelf Supports
Hardware for Step 9:
8x #5 Flat Head Screws
#5 x4
#5 x4
#5 x4
H
I
I
#11
#11
#11
#11
#11
#11
#11
#11
#11

9
STEP 11:
Your unit is now ready to use.
This unit should NOT be used on it’s own, it must be used with an appropriate
Alba REGULAR base unit.

10 Copyright© 2019 G.L.T.C. Ltd.All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.
2Lateral/Horizontal Adjustment: Moving the door side to side. (To control
the gaps between the door and the side panels)
#A2
#A3
Release screw A2 a little (this is a locking screw).
Then turn A3 screw to adjust the position of the door
(tighten or loosen)
Adjust one hinge at a time.
When correct position is achieved, re-tighten screw A2
on each hinge.
Repeat with the second door
3Forward/backward Adjustment: Moving the door in or out. (To make sure the
doors are ush with the front edge of the side panel)
#A2
Turn screw A2 a little to adjust the door.
Adjust one hinge at a time.
When correct position is achieved, repeat with the
second door.
1Vertical Adjustment: Moving the door up and down. (To control the gaps
between the door and the top/bottom panels)
#A1
Ensure one person is
holding the door. Unscrew/
loosen the screws shown
on each hinge of one door.
Do not remove the screws
completely.
Once the screws are
released, move the door to
the required position.
When in the corrected
position, re-tighten the
screws.
Repeat with the second
door.
#A1
#A1
Hinge Adjustment - For cupboards with cup hinges
Note: 2 people should complete the adjustment. One holding the
door, one adjusting the screws
#A1