Great Little Trading Wonderland Bookcase L5291 User manual

1
Wonderland Bookcase
27/10/2021
V1
one-person job
Assembly Difculty
easy - medium - hard
A few important pointers before you start:
• Please read the instructions right through before you start, and
check that all the components have been included in the pack;
we nd separating all the hardware into piles makes it easier to
be sure that everything is present and correct.
• Make sure you have the right tools.Allen keys are provided
if required, but screw drivers and other tools are not.You’ll
nd details of the tools you need at the beginning of the
instructions.
• It’s a good idea to build the unit in the room where you are
going to be using it, to avoid the need to move it after it’s been
assembled.
• Do not throw away any packing materials until assembly is
complete, just in case you accidentally discard smaller parts or
hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
L5291

2
Safety Warnings:
• Adult assembly required.
• Unassembled product contains small parts which may present a choking
hazard.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• Assemble and use on a at and level surface.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• Maximum shelf weight: 15 Kgs. Maximum overall weight 80 Kgs. DO NOT
overload.
• To avoid possible injury from tipping, DO NOT allow children to climb
on the product.
• WARNING! FURNITURE TIPPING RISK. Serious or fatal crushing
injuries can occur from furniture tipping over. Ensure you secure this
furniture product to the wall before you use it, using the kit provided.
• If you have not received an anti-tip kit with your product please contact
Customer services.
• Wall xings not included. Please use appropriate xings that are suitable
for the wall type. If in doubt, please seek professional advice.
• Check all xtures and ttings regularly and tighten as necessary.
• PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
• Regularly check all fastenings, xtures and ttings to ensure that they
are properly tightened.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
AB
CD
EF
G
2x Shelves 1x Front Vertical
Divider
1x Side Vertical Divider
3x Wooden Poles
#1 #2
#3 #4
#5 #6
#7 #8
x 17 Cam Dowels x 36 Wooden Dowels
You will need (not supplied)
Philips Head Screwdriver
1x LH Side Panel
(Storage Side)
1x RH Side Panel
(Full Depth)
1x Back Panel
(Side Storage)
Component Check List
Hardware Check List
x 17 Cam Locks x3 Crosshead Bolts
x3 Barrel Nuts x2 Wood Screws (25mm)
x14 Screws x1 Anti-Tip Kit
H
1x Base Panel
I J
K
1x Top Panel 2x Batons
1x Back Panel
(Main Storage)
Component Check List

4
A
A
B
A
A
B
C
STEP 1:
Working on a protective surface like a carpet or a rug, take
front vertical divider panel (B) and position with the slots
facing up and the large drill holes on the side facing left (as
shown).
Now take one shelf panel (A) and slot together with panel
(B) as shown. Ensure the shelf is positioned with the upstand
facing towards the top, drill holes facing down and the second
slot on the short side pointing left.
Repeat with 2nd shelf panel (A).
TOP
BASE
STEP 2:
Take the side vertical divider panel (C) and push into the slots
on the 2x shelves (A) on the left hand side.
Ensure panel (C) is positioned with any drill holes facing the
oor before slotting into place.
TOP
BASE

5
Hardware for Step 4:
4x #2 Wooden Dowels
Hardware for Step 3:
2x #1 Cam Dowels
#1
#1
D
E
E
E
D
B
A
A
C
#2
#2
#2
#2
#3
#3
#2
#3
E
2x #3 Cam Locks
STEP 3:
Prepare LH side panel (D) by
inserting 2x cam dowels (#1) into the
central drill holes as shown using a
Phillips screwdriver.
TOP
BASE
STEP 4:
Adding the wooden poles and the book storage side panel.
Firstly, add 2x wooden dowels (#2) into the outer holes in
the ends of BOTH shelf panels (A).
Now place the 3x wooden poles (E) into the drill holes on
the side of the central divider resting the other end on panel
C whilst you prepare to join panel D to the unit.
Position side panel (D) with the smaller drill holes at the
end of the panel at the base end (this is not shown, but do
check). Align the hardware on panel D with the shelf ends
and also the large drill holes with the wooden poles and push
panel into place. Ensure the poles are in place at both ends
and then insert 2x cam locks (#3) into the drill holes on
the underside of BOTH shelf panels (A). Turn clockwise to
secure the panel.
Using Cam Locks:
When inserting into the
panel, ensure that each cam
lock’s arrow is pointing
towards the drill hole on the
side edge of the panel & the
dowel that it will be receiving.
When the panels are in the
connected position, using a
screwdriver, turn the cam
lock in a clockwise direction
to lock and secure.
Once
step
4 is
complete,
carefully
turn the unit
over so the
wooden poles are
towards the oor.
Ensure you keep the
top and bottom in the
same positions.

6
Hardware for Step 5:
4x #1 Cam Dowels
Hardware for Step 6:
4x #3 Cam Locks
4x #2 Wooden Dowels
F
#1
#1
#1
#1
#1
#2
#2 #2
#2
#3
#3
#3
#3
A
A
CF
B
STEP 5:
Prepare the RH Side panel (F) by
inserting 4x cam dowels (#1) into the
outer holes on each set of drill holes.
BASE
(With smaller
drill holes)
TOP
(With larger drill
holes)
STEP 6:
The unit is now facing with its BACK UP.
Insert 2x wooden dowels (#2) into the inner holes in the ends of BOTH
shelf panels (A).
Take RH side panel (F) and position with the recessed edge facing up and
smaller drill holes on the face of the panel at the base end.
Align the hardware on panel F with the shelf ends and push into place.
Insert 2x cam locks (#3) into the large drill holes on the underside of
BOTH shelf panels (A). Turn clockwise to secure in place.
TOP
BASE
#3

7
Hardware for Step 8:
Hardware for Step 7:
4x #1 Cam Dowels 4x #2 Wooden Dowels
#1
G#1
#1
#1
#2
#2
#2
#2
#3
#3
#3
#3
G
FB
C
#5
#5
#2
#3
4x #3 Cam Locks
1x #5 Barrel Nut
STEP 7:
Prepare the thicker back panel (G) by
inserting 4x cam dowels (#1) into the outer
holes on each set of drill holes.
STEP 8:
Insert 2x wooden dowels (#2) into the inner
holes on the edges of BOTH shelf panels (A).
Position panel G with the large drill holes facing
up/outwards and align the hardware on the
underside with the edges of both shelf panels (A).
Push into place.
Now insert 2x cam locks (#3) into the large drill
holes on the underside of BOTH shelf panels (A).
These will now be inside the unit. Ensure you
insert all 4 cam locks (#3) and turn clockwise to
secure in place.
Finally, insert 1x barrel nut (#5) into the visible
hole on the inside face of panel D at the base end
as shown. This will be needed in a later step.
A
A
TOP
BASE

8
#1
#1
#1
#1
I
#1
#1
#1
H
G
F
#5
#5
#2
#5
#2
#2
#2
#2
#4
#2
#4
#4
#2
#2
#2
#2
#2
#3
#4
H
Hardware for Step 9:
7x #1 Cam Dowels
Hardware for Step 10:
2x #3 Cam Locks
10x #2 Wooden Dowels
2x #5 Barrel Nuts
STEP 9:
Take top panel (I) and base panel (H) and position
with the drill holes facing up.
Insert 5x cam dowels (#1) into the holes shown on
top panel (I).
Then insert 2x cam dowels (#1) into the holes
shown on base panel (H).
STEP 10:
Add the base panel.
Start by inserting 2x barrel nuts (#5) into the
holes on the inside face of side panel (F).
Now insert 10x wooden dowels (#2) into the
following panels:
- F & G: 2x #2 in the inner holes of panel ends.
- D: 2x #2 in the outer holes of panel end.
- B & C: 2x #2 into the holes on the panel ends.
Align the hardware on base panel (H) with the
holes of the panel on the built unit and push
into position.
Insert
2x cam
locks (#3)
onto the large
holes on back
panel (G) and turn
clockwise to lock.
Insert 3x crosshead
bolts (#4) into the holes
on the LH & RH sides of
the base panel (H) to secure
the side panels on both sides.
B
3x #4 Crosshead Bolts
D
#1
#3
#3

9
H
J
J
#6
#6
#2
#2
#2
#2
#2
#2 #2
#2
#2
#2 #2
#2
#3
#3
#2
#2
#3
#3
#2
#3
F
G
I
Hardware for Step 11:
4x #2 Wooden Dowels
2x #6 Wood Screw (25mm)
Hardware for Step 12:
10x #2 Wooden Dowels
4x #3 Cam Locks
STEP 11:
Attach the 2x batons (J) on each side of the
base panel.
Insert 2x wooden dowels (#2) into the holes
next to the feet. Push the baton into position
and x in place with 1x screw (#6) using a
Phillips screwdriver.
Repeat on remaining side.
STEP 12:
Attach the top panel.
Insert 10x wooden dowels (#2) into the
following panels:
- F & G: 2x #2 in the inner holes of panel ends.
- D: 2x #2 in the outer holes of panel end.
- B & C: 2x #2 into the holes on the panel ends.
Orientate top panel (I) with the recessed section
facing up as shown.
Align the hardware on top panel (I) with the
holes of the panel on the built unit and push into
position.
Insert 2x cam locks (#3) onto the large holes
on back panel (G) and 2x cam locks (#2) on the
inside face of side panel (F) and turn clockwise
to lock.
B
D

10
F
H
G
K
#7
#7
#7
#7 #7
#7
#7
#7
#7
#7
#7
#7
#7
#7
#7
#3
#3
Hardware for Step 13:
14x #7 Back Panel Screws
Hardware for Step 14:
1x #3 Cam Lock
STEP 13:
Attach the remaining back panel.
Position back panel (K) on the unit and check
the alignment of the holes in the panel with
those on the unit.
Using your Philips screwdriver, x the panels in
place with x14 screws (#7).
Please note that the 2x pilot holes indicated at
the top of the unit are to attach the anti-tip kit
included separately with this item.
Please note:
These arrows
indicate the drill
holes used for the
anti-tip kit brackets
& hardware
included in with
your unit. Do not
use hardware #7 in
these holes.
STEP 14:
Carefully stand the unit up on its feet.
Add the nal cam lock into the drill hole on the
inside of side panel (D), it is accessed through
the upper book storage area.Turn clockwise to
lock.
D