Great Little Trading Star Bright L3959 User manual

1
Star Bright Bookcase
A few important pointers before you start:
•It might be worth checking on our website that there are no updates
or revisions to these instructions (if we have had helpful feedback from
other customers we pass it on via the product web page). Simply check
any site updates.
•Please read the instructions right through before you start, and check
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
•Make sure you have the right tools. Allen keys are provided if required,
tools you need at the beginning of the instructions.
•It’s a good idea to build the unit in the room where you are going to be
using it, to avoid the need to move it after it’s been assembled.
•Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
L3959
20/05/2016
V1
easy - medium - hard two-person job
Thank you for shopping with GLTC, we hope you enjoy having
this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail through
the whole process. But if it all feels a bit too much like hard work, then
we do have an assembly company we can recommend: the Flatpack
Construction Company offers a nationwide service and can be
contacted on
Good luck!

2
Safety Warnings:
• Adult assembly required.
• Unassembled product contains small parts which may present a
choking hazard.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• Assemble and use on a at and level surface.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• To avoid possible injury from tipping, DO NOT allow children to climb
on the product.
• Always use the wall straps provided.
• Wall xings not included. Please use appropriate xings that are
suitable for the wall type. If in doubt, please seek professional advice.
• Check all xtures and ttings regularly and tighten as necessary.
• Please retain these instructions for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
Component Check List Component Check List
#1 #2
#3
#5
#7
#4
#6
14x Cam Locks
14mm Diameter
4x Barrel Nuts
18x Screws
17.5mmL
14x Cam Dowels
35mmL
20x Wooden Dowels
20mmL
4x Threaded Bolts
42mmL
1x Allen Key
Phillips Head Screwdriver
You will need (not supplied)
A B
C
E
G
I
D
F
H
1x LH Side Panel
1x Star Panel
1x Top Panel
1x Middle Back Panel
1x RH Side Panel
2x Shelf Panels
1x Base Panel
1x Lower Back Panel
1x Upper Back Panel

4
STEP 1:
Take both side panels (A & B) and insert 4x cam dowels (#1) into the outside holes
on EACH panel.
NOTE:
You will be building this unit face down. To make later steps easier and also to protect
the product during the building process, we suggest laying the polystyrene packing
down on the oor rst and building on top of it.
Hardware for Step 1:
8x #1 Cam Dowels
STEP 2:
Take the two shelf panels C and the star panel D and position them as shown against
the RH side panel A. Ensure the edges of the shelves with the small pilot holes are
facing upwards and the large drill holes on the shelves themselves are facing down
towards the base of the unit. Also check that the large holes on the star panel are
facing up, as shown.
Push the three panels into place using the wooden dowels (#3) and then secure the
shelves by inserting 4x cam locks (#2) and turning clockwise to lock.
A
TOP
BASE
B
#1
#1
#1
#1
BASE
TOP
#1
#1
#1
#1
A
BASE
TOP
C
C
D
6x #3 Wooden Dowels
Hardware for Step 2:
4x #2 Cam Locks
#2
#3
#2
#2
#2
#3
#3
#3
#3
#3

5
TOP
BASE
STEP 3:
Position the left hand side panel B onto the unit using the xed hardware and the
wooden dowels (#3). Ensure the smaller drill holes on the side panel are at the base
end of the unit.
Secure the shelves to the side panel by inserting 4x cam locks (#2) into the large drill
holes and turning clockwise to lock.
STEP 4:
Attach the base panel E to the rest of the unit using wooden dowels, bolts and barrel
nuts as shown. Tighten the bolts using the Allen key provided.
C
6x #3 Wooden Dowels
Hardware for Step 3:
4x #2 Cam Locks
#2
#3
#3
#3
#3
#2
#2
C
D
B
TOP
BASE
#2 #3
#3
Hardware for Step 4:
4x #5 Barrel Nuts
4x #4 Bolts
4x #3 Wooden Dowels
#5
#4
#4 #4
#4
#5
#5
#5
#3
#3
#3
#3
E
B
A
NOTE:
This is where it helps building on the polystyrene
packaging.The unit will now be raised slightly making
it easier to attach the base & top panels without
having to lift up the part constructed unit.

6
STEP 6:
Position the top panel F onto the unit using the xed
hardware and wooden dowels (#3). Once in place,
insert 6x cam locks (#2) into the larger
holes on the side and star panels and
turn clockwise to secure the
top panel in place.
STEP 5:
Prepare the top panel F.
STEP 7:
Attach the back panels using the longer, thinner screws (#6). Check that the back
panels are positioned as shown.
NOTE:
The two pilot holes on the top corners of the upper back panel need to be left free
for Step 8.
G
4x #3 Wooden Dowels
Hardware for Step 6:
6x #2 Cam Locks
FRONT
F
TOP
BASE
#6
#2
#3
BACK
Hardware for Step 5:
6x #1 Cam Dowels
#1
#1
#1
#1
#1
#1
#2
#2
#2
#2
#2
#3 #3
#3
F
B
A
H
I
#6
#6
#6
#6
#6
#6
#6
#6
#6
#6
#6
#6
#6 #6
#6
#6
#6
Hardware for Step 7:
18x #6 17.5mmL Screws

7
STEP 8:
TOP
Copyright© 2016 G.L.T.C. Ltd.All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.
Your unit is ready to use.
Please not that the 2x pilot holes indicated
at the top of the unit are to attach anti tip
straps included separately with this item.
Please be aware that we advise that safety straps are used to
secure this to the wall, for details on securing the unit to the wall see
the anti-tip kit guidance. Alternative furniture safety straps are
available at www.gltc.co.uk