Great Little Trading L1420 User manual

1
A few important pointers before you start:
• Please read the instructions right through before you start, and check that all the
components have been included in the pack; we nd separating all the hardware
into piles makes it easier to be sure that everything is present and correct.
• Make sure you have the right tools.Allen keys are provided if required, but screw
drivers and other tools are not. You’ll nd details of the tools you need at the
beginning of the instructions.
• It’s a good idea to build the unit in the room where you are going to be using it, to
avoid the need to move it after it’s been assembled.
• Do not throw away any packing materials until assembly is complete, just in case
you accidentally discard smaller parts and hardware.
Northcote Divider Unit
L1420
easy - medium - hard one-person job 24/01/2017
Thank you for shopping with GLTC, we hope you enjoy having this
product in your home.
We know assembling furniture, toys or accessories is not everyone’s favourite
way to spend their time, so we’ve tried to make assembling this item as quick and
painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail through the
whole process. But if it all feels a bit too much like hard work, then we do have
an assembly company we can recommend: the Flatpack Construction Company
offers a nationwide service and can be contacted on 0843 289 4951 or www.
atpackconstruction.co.uk.
Assembly Difculty
www.gltc.co.ukwww.gltc.co.uk
V2

2
Safety Warnings:
• Anti-tip furniture straps are recommended for use on the Northcote range. Anti-
tip furniture straps (G5323) are available from gltc.co.uk.
• It is recommended that the Northcote modular storage furniture is only stacked
3 units high, inclusive of the base unit. E.g. 1 x Base unit + 2 x Shelf units.
• Adult assembly required.
• Assemble and use on a at surface.
• CHOKING HAZARD – This product contains small parts and must be assembled
by an adult. Special care should be taken in the unpacking and assembly of this
item as unassembled parts may be a choking hazard to children under 3 years old.
• During assembly, children should be kept away from the product due to possible
risk of injury.
• Do not use power tools in the construction of this product.
• This product is heavy, so we recommend that you build it where you are planning
to use it.
• All assembly fastenings should be tightened properly and periodically checked;
care should be taken that no ttings are loose.
• Keep all relevant information for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do not begin
assembly and do not use the item. Please contact GLTC Customer Services on
0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be able to
send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which may contain ammonia, solvents or abrasive
material.
• Do NOT expose the furniture to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in the assembly
of this product we’d be grateful if you could let us know; we’ll pass any helpful hints and
tips on to other customers via our website and update the instructions.
All you need to do is drop us a line at [email protected]
Thank you

3
Unit Side Panels
(left & right)
Central Divider Panel
1x Unit Base
(lip at top & bottom)
C
1x Unit Top
(recessed groove at top)
A
B
2x Back Panels
E F
Component Check List: All Hardware
#1 #2
#3 #4
8x Cam Dowels
45mmL
8x Cam Locks
14mmDia
8x Wooden Dowels
20mmL
8x Shelf Fixings
15mmL
You will need:
(not supplied)
Philips Head Screwdriver
Component Check List: Divider Unit 2x Shelf Panels
D

4
Assembly
STEP 1:
Lay the 2 x side panels (C) on a clean at surface with the drill
holes and groove facing up, in the position shown.
Insert 4 x wooden dowels (#3) into the drill holes in the four
corners of BOTH side panels (C). Ensure they are pushed in as
far as they will go.
Insert 4 x cam dowels (#1) into the drill holes next to the
wooden dowels on BOTH panels (C), tighten with a screw
driver.
NB: Wooden dowels should t snuggly and push in with your ngers. Do not use force or a
hammer as the wood may split.
C
#1
#3
Hardware for Step 1:
8x #1 Cam Dowels
8x #3 Wooden Dowels
left
STEP 2:
Take the unit top (A) and unit base (B) and place them on a clean
at surface with the drill holes facing up.
Insert the 8x cam locks (#2) into the drill holes.
Ensure that each cam lock’s arrow is pointing towards the drill hole
on the side edge of the component.
A
B
Hardware for Step 2:
8x #2 Cam Locks
#2
Ensure that each cam lock’s arrow is
pointing towards the drill hole on the side
edge of the component.

5
STEP 3:
Position unit base (B) over the left hand side panel (C) as shown, so
that the recessed grooves on each panel are aligned. Guide the unit
base (B) over the cam dowels and wooden dowels onto the lower edge
of the side panel (C) and into the drill holes on the edge of the panel.
When in position, push down rmly and secure by tightening 2 x cam
locks (#2) by turning clockwise, at the point of connection between the
two panels.
When in position, turn the 2 x
cam locks (#2) on the unit base
(B) clockwise to lock in place.
B
C
left
STEP 4:
Position the unit top (A) over the shaped top edge of the side
panel (C) as shown, and so the recessed groove lines up on
both panels. Guide the unit top (A) over the cam dowels and
wooden dowels, into the drill holes on the edge of the panel.
When in position, push down rmly and secure by tightening
the 2 x cam locks (#2) on unit top (A).
When in position, turn the 2 x
cam locks (#2) on the unit top
(A) clockwise to lock in place.
B
A
C
left

6
STEP 5:
Insert the divider panel (F) between the unit top (A) and unit base (B) as shown, ensuring that the
protrusions on the divider panel are sitting securely in the corresponding recesses of the unit top (A) &
base (B).
B
A
F
B
STEP 6:
Gently, slide the 2x back panels (E) into the recessed groove of the unit top (A) and base (B), ensuring it is
pushed all the way in to the groove on the side panel (C).
E
E

7
STEP 7:
Position the remaining side panel (C) over the unit. Guide the cam dowels and wooden dowels on the side
panel into the drill holes on the edges of the unit top (A) and base (B).
Once rmly in place, turn the 2 x remaining cam locks (#2) on the unit base (B) clockwise until they lock.
Then turn the 2 x remaining cam locks (#2) on the unit top (A) clockwise until they lock.
E
E
B
C
When in position, turn the four remain-
ing cam locks (#2) on the unit top &
base clockwise to lock in place.
right
STEP 8:
Turn the unit up the right way and insert the shelf pegs (#4) into the drill holes on each side of the divider
unit at the required shelf height.
Note: 4 x shelf pegs (#4) are needed to secure each shelf into position.
A
Hardware for Step 8:
8x #4 Shelf Pegs
#4

8
STEP 9:
Position the 2 x shelf panels (D) over the shelf pegs and press
down rmly so that they are securely in place.
Your unit is now ready to use.
Please ensure you are using this unit with L1422 Northcote Toy Box Base
or L1423 Northcote Open Base.
D
D
Copyright© 2011 G.L.T.C. Ltd.All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.