Great Little Trading L4471 User manual

1
Alba Corner Shelf Unit
L4471
easy - medium - hard
Assembly Difculty
two-person job
A few important pointers before you start:
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools.Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the tools
you need at the beginning of the instructions.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail
through the whole process. But if it all feels a bit too much
like hard work, then we do have an assembly company we
can recommend: the Flatpack Construction Company offers a
nationwide service and can be contacted on 0843 289 4951 or
www.atpackconstruction.co.uk.
07/06/2019
V1

2
Safety Warnings:
Please read these instructions carefully before assembly.
• Warning! Not suitable for children under 3 years due to small parts
which may become detached and present a choking hazard.
• Assembly by a competent adult is required.
• Unassembled product contain small parts which may pose a choking
hazard to young children.
• During assembly children should be kept away from the product due
to possible risk of injury.
• Assemble and use on a at and level surface.
• This product is heavy, we recommend that you build it where you are
planning to use it.
• This unit can only be used in conjunction with other Alba Corner
units.All stacked Alba furniture must start with a GLTC Alba base unit.
• It is recommended that the Alba range is only stacked 3 units high i.e.
1x corner base + top shelf & 2x corner shelf units.
• DO NOT use power tools in the assembly of this product as there is a
risk of over tightening and consequently splitting of the wood.
• Do not over tighten hardware. Cam dowels should be inserted to
the collar. Back panel screws should be screwed until they naturally
tighten/stop. This is difcult to feel if power tools are being used.
• Do not use if any parts are missing or damaged as this may lead to
products being unstable.
• WARNING! FURNITURE TIPPING RISK. Serious or fatal crushing
injuries can occur from furniture tipping over. Ensure you secure this
furniture product to the wall before you use it, using the kit provided
in the base unit.
• To avoid possible injury from tipping - DO NOT allow children to step
or climb on the product.
• Check all xtures and ttings regularly and tighten as necessary.
• Remove all packaging before allowing your child to use the product.
• Please retain for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
• Regularly check all fastenings, xtures and ttings to ensure that they
properly tightened.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
A B
C D
E F
G H
I
1x LH Side Panel
Component Check List Component Check List
J
K L
1x RH Side Panel
1x RH Base Panel
1x LH Shelf Panel 1x RH Shelf Panel
1x Back Support Panel
1x Back Support Panel
(with drill holes on edge)
2x RH Back Panels 2x LH Back Panels
1x LH Top Panel 1x RH Top Panel
1x LH Base Panel

4
#1 #2
#3 #4
#5 #6
You will need
(not supplied)
Philips Head Screwdriver
Component Check List
16x Cam Dowels
35mmL
28x Wooden Dowels
25mmL
16x Cam Locks
15mmL dia
32x Domed Head Screws
14mmL
6x Double Ended Cam Dowels

5
STEP 1:
Join all the corner panels together.
Take top panels C & D and position with large drill holes facing up and the
angled edges next to each other as shown.
Insert 2x wooden dowels (#2) into the inner holes on the angled edge of
panel C.
Insert 2x double ended cam dowels into the outer holes on the edge of the
same panel.
Insert 2x cam locks into the large drill holes on the same panel and turn
clockwise to lock.
Pull the ends of cam dowels out a little.
Now push the two panels together and insert 2x cam locks (#3) into the large
drill holes on panel D and turn clockwise to lock.
Repeat for base panels E & F and shelf panels G & H.
Ensure all cam locks are tightened before moving to the next step.
G H
#3
#3
#5
#2
#2
#5
#3
#3
#2
#3
Hardware for Step 1:
6x #2 Wooden Dowels
12x #3 Cam Locks
6x #5 Double Ended
Cam Dowels
C D
E F
#3
#3
#3 #3
#3
#3
#3#3
#5
#5
#5
#5
#2 x2
#2 x2
#3
#2
Using Cam Locks:
When inserting into the panel, ensure that each cam lock’s
arrow is pointing towards the drill hole on the side edge of
the panel & the dowel that it will be receiving.
When the panels are in the connected position, using a
screwdriver, turn the cam lock in a clockwise direction to
lock and secure.

6
STEP 3:
Carefully turn joined panels E & F over, to show the small set of drill holes in
the corner.
Insert 2x cam dowels (#1) into the smaller, middle drill holes in the corners of
the C/D & E/F sets of joined panels.
Hardware for Step 3:
4x #1 Cam Dowels
C D
EF
#1 #1
#1 #1
STEP 2:
Using a Phillips screwdriver, insert 6x cam dowels (#1) into BOTH side panels
A & B.
Hardware for Step 2:
12x #1 Cam Dowels
A
B
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1

7
STEP 5:
Take the C/D top panels and insert 4x wooden dowels (#2) into the
remaining holes in the corner.
Push into the drill holes on the edges of panels I & J.
Insert 1x cam lock (#3) in the large hole on panel J and turn clockwise to
lock.
Take the E/F base panels and insert 4x wooden dowels into the remaining
holes in the corner.
Now push this onto the back support panels I & J.
Insert 1x cam lock in the large hole on panel J and turn clockwise to lock.
NOTE: The cam locks on panel I will be secured at a later stage.
E
F
Hardware for Step 5:
8x #2 Wooden Dowels
2x #3 Cam Locks
G
H
C
D
J
#2 x4
#2 x4
#2 x4
#3
#3
#3
STEP 4:
Lay back support panel I at on the oor. The large drill holes on the panel
to be facing the oor and the small pilot holes on the edge MUST be facing
outwards.
Take the joined G/H shelf panels and insert 2x wooden dowels (#2) into the
holes in the corner.
Connect the shelf panel with panel I.
Now take back support panel J and position with the drill holes facing
outwards. Push onto the dowel of G/H. It will sit on the top of panel I.
Hardware for Step 4:
2x #2 Wooden Dowels
G
H
I
J
#2
#2
#2
BASE
TOP
It is important that these small pilot
holes are visible and in this position on
panel I, as they are needed in a later step.
BASE
TOP

8
STEP 7:
Keeping the unit in the same position, repeat step 6 with panel B.
This time, ensure the grooved edge is facing the the oor.
Tighten all cam locks fully.
Now the unit is stable, please carefully rotate it onto its base.
Hardware for Step 7:
6x #2 Wooden Dowels
6x #3 Cam Locks
E
FG
H
C
D
#3
#2
#2
#2
#2
#2
#2
#3
#3
#3
#3
B
A
STEP 6:
Take side panel A and insert 6x wooden dowels in the remaining drill holes.
Line up the grooved edge on panel A with the grooved edges of the corner
panels and push on to the ends of panels D, F & H.
Insert 6x cam locks into the drill holes on panels D, F & H and turn clockwise
to lock.
Hardware for Step 6:
6x #2 Wooden Dowels
6x #3 Cam Locks
#3
#3
#3
#3
#3
#3
#2
#2
#2
#2
#2
#2
#3
E
FG
HC
D
A

9Copyright© 2019 G.L.T.C. Ltd.All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.
STEP 9:
IMPORTANT! Before the back panels are secured, please insert 2x cam locks
(#3) into the remaining holes on panel I.Turn clockwise to lock.
Take 2x back panel L and starting with the lower panel, align with the drill
holes in the grooved edges of panel E & C.
Note the the positioning of panels L. At one end the drill holes are set further
into the panels. This end needs to be at the corner join.
Secure with 16x domed head screws (#4).
Take 2x back panels K and starting with the lower panel, align with the drill
holes in the grooved edges of panels F & D.
Again, the holes on the panel that are set further in should be at the corner
join.
Secure with 16x domed head screws (#4).
Hardware for Step 9:
32x #4 Domed Head Screws
#4 x8
#3
D C
Your unit is now ready to use.
This unit should NOT be used on it’s own, it must be used with the Alba
CORNER base unit.
IMPORTANT: This unit is very heavy and will need two people to move it
or stack it on top of the Alba Corner base Unit or Alba Corner Shelf Unit
2x #3 Cam Locks
K
K
L
L
#3
#4 x8
#4 x8
#4 x8