Great Little Trading l3939 User manual

1
Star Bright Wardrobe
A few important pointers before you start:
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools. Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the
tools you need at the beginning of the instructions.
• It’s a good idea to build the unit in the room where you are going to be
using it, to avoid the need to move it after it’s been assembled.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
30/05/2019
V5
easy - medium - hard
Assembly Difculty
two-person job
Thank you for shopping with GLTC, we hope you enjoy having
this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail through
the whole process. But if it all feels a bit too much like hard work, then
we do have an assembly company we can recommend: the Flatpack
Construction Company offers a nationwide service and can be
contacted on 0843 289 4951 or www.atpackconstruction.co.uk.

2
Safety Warnings:
• Adult assembly required.
• Unassembled product contains small parts which may present a
choking hazard.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• Assemble and use on a at and level surface.
• This product is suitable for children aged 3 years+.
• Maximum weight for drawer is 12kgs, maximum weight for
the hanging rail is 25kgs.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• To avoid possible injury from tipping, DO NOT allow children to climb
on the product.
• Always use the wall straps provided.
• WARNING! FURNITURE TIPPING RISK. Serious or fatal crushing injuries
can occur from furniture tipping over. Ensure you secure this furniture
product to the wall before you use it, using the kit provided. If you have not
received an anti-tip kit with your product please contact Customer services.
• Check all xtures and ttings regularly and tighten as necessary.
• IMPORTANT: PLEASE RETAIN THESE
INSTRUCTIONS FOR FUTURE REFERENCE
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [email protected]
Thank you

3
Component Check List Component Check List
A B
C
E
G
I
D
F
H
1x Upper RH Side Panel
1x Top Panel
1x LH Lower Side Panel
1x Base Panel
1x Upper LH Side Panel
2x Back Rails
1x Mid Panel
1x RH Lower Side Panel
1x Upper Back Panel
J
1x Middle Back Panel
K L
M
O
Q
S
N
P
R
1x LH Drawer Side
1x Drawer Front
1x Drawer Base
1x LH Door
1x Lower Back Panel
1x RH Drawer Side
1x Drawer Back
1x Hanging Rail
1x RH Door

4
Component Check List Component Check List
#11 #12
#13
#15
#14
#16
4x Screws
25mmL
6x Hinge Base Plates
1x RH FlatRunners
1x LH ‘L-Shaped’ Runner
1x RH ‘L-Shaped’ Runner
2x Collars
#1 #2
#3
#5
#7
#9
#4
#6
#8
24x Cam Locks
14mm Diameter
16x Wooden Dowels
20mmL
12x Threaded Bolts
42mmL
16x Screws
4mm Diameter x12mmL
24x Cam Dowels
35mmL
2x Rail Mount Plates
Note: These plates may come connected to
Part #13, please unscrew to separate.
12x Barrel Nuts
24x Screws
4mm Diameter x12mmL
26x Screws
16mmL
#10
26x Screws
16mmL
1x LH Flat Runner
1x Allen Key
Phillips Head Screwdriver
You will need (not supplied)
#17 #18
6x Hinges
2
2
2
2

5
STEP 1:
You will need plenty of space to build this unit as the panels are large. We also
suggest you use a carpeted area to protect the panels during the build.
Firstly, decide on the desired height of the hanging rail.There are two positions to
choose from.The higher position offers 120cm of hanging space, the lower position
offers 105cm.The illustration shows the use of the higher position.
Once the position is decided, attach the rail mounting plates (#3) to panels A & B.
Now, insert 4x cam dowels (#1) into the holes along
B
BACK
A
BACK
Hardware for Step 1:
8x #1 Cam Dowels
2x #3 Rail Mount Plates
4x #8 12mmL Screws
#82x
#82x
#12x
#12x
#12x
#12x
#3
#3
TOP
TOP
BASE
BASE
STEP 3: 2 people are needed for this step.
NOTE: You will be building this wardrobe face UP, so the back of the unit will be on
the oor. Align panels A and B as shown ensuring that the groove along the long edge
is to the oor.
Position and connect 2x panel C ensuring the large drill holes are facing down so you
cannot see them. DO NOT turn the unit over to x these panels in place, this step
will be completed at a later stage.
TOP
BASE
C
C
A
B
BACK
BACK
STEP 2:
Prepare the top panel (D) by
inserting 6x cam dowels (#1).
Note: The block on the
underside of the panel
indicates the front
of the panel.
#1
#1
#1 #1
#1
#1
Hardware for Step 3:
6x #1 Cam Dowels
D
FRONT

6
TOP
BASE
STEP 4:
Insert 4x wooden dowels (#4) to top panel (D) and connect to side panels A and B
securing with 6x cam locks (#2).
Note: Rounded corners and block on top panel D to be uppermost.
STEP 5:
Prepare panel E by inserting 6x
cam dowels (#1) where indicated.
Note the correct position
of this hardware - there
are more drill holes here
that will be used on the
next stages.
A
4x #4 Wooden Dowels
Hardware for Step 4:
6x #2 Cam Locks
#4
#4
#4
D
B
#4
Hardware for Step 6:
6x #5 Barrel Nuts
6x #6 Bolts 42mm
4x #4 Wooden Dowels
E
#23x
#23x
Hardware for Step 5:
6x #1 Cam Dowels
#13x
#13x
STEP 6:
Insert 4x wooden dowels (#4) and 6x barrel nuts (#5)
to the ends of panels A and B. Position panel E to the
ends of panels A and B so that the grooved edge is
facing the oor and it connects to the wooden dowels
(#4). Secure panel with 6x bolts (#6) using the Allen
key provided.
E
#53x
#53x
#63x
#63x
#4
#4
#4
#4
A
B
TOP
BASE
FRONT

7
STEP 7:
NOTE:The back edge of the panels is the one with the groove along it.
Attach LH at runner (#10) to panel F as shown ensuring that the wheel of the
runner is nearest to the at end of the panel (front).
Attach RH at runner (#11) to panel G also ensuring that the wheel of the runner is
nearest the at end of the panel (front).
When xed in the correct position, there will be a gap between the front edge of the
panel and the start of the runner. If the front of runner is level with the edge of the
panel, it is in the wrong position.
STEP 8:
Insert 4x wooden dowels (#4) to panel E and connect side panels F and G as shown
ensuring that the wheel of the runners is at the top. Secure these panels with 6x cam
locks (#2).
Hardware for Step 7:
1x #10 LH Flat Runner
1x #11 RH Flat Runner 4x #4 Wooden Dowels
Hardware for Step 8:
6x #2 Cam Locks
#4
#4
#4
#4
#4
#23x
#23x
E
F
G
6x #8 12mmL Screws
G
#8
#8
#8
#11
F
#8
#8
#8
#10
BACK
FRONT
FRONT
BACK
Use the smaller holes when
attaching the runner. Start
with the rst small next to
the wheel.

8
STEP 9:
Insert 4x wooden dowels (#4) and 6x barrel nuts (#5) to the ends of panels F and
G. Position base panel H to the ends of panels F and G ensuring that the rounded
corners are facing upwards and it connects with the wooden dowels (#4). Secure
panel with 6x bolts (#6) using the Allen key provided.
FH
G
#53x
#53x
#63x
#63x
#4
#4
#4
#4
Hardware for Step 10:
8x #2 Cam Locks
STEP 10:
IMPORTANT:Two people are needed to complete the next step safely.
Carefully turn the unit over so the back is facing up.
Insert 8x cam locks (#2) into the large drill holes on the two back panels (C).Turn
clockwise to lock.
C
C
#22x
#22x
#22x
#22x
Hardware for Step 9:
6x #5 Barrel Nuts
6x #6 Bolts 42mm
4x #4 Wooden Dowels
Rounded corners to face upwards

9
STEP 12:
Attach LH L-shaped’ runner (#13) to drawer side panel L as shown with 3x screws
(#8). Ensure that the wheel of the runner is at the end with the 2x pilot holes.
STEP 11:
Place back panels K, J and I onto the ledged recess on the back of the unit ensuring
that the holes in the panels match the pilot holes in the unit. Secure the panels with
26x screws (#9).
J
K
I
#926x
1x #13 LH ‘L-Shaped’
Runner
Hardware for Step 12:
3x #8 12mmL Screws
Please note that the 2x pilot holes indicated
at the top of the unit are to attach anti-tip
straps included separately with this item.
See step 22.
Hardware for Step 11:
26x #9 16mmL Screws
#8
#8
#8
#13
L
#8
#8
#8
#13

10
Hardware for Step 14:
4x #1 Cam Dowels
STEP 13:
Attach RH L-shaped’ runner (#12) to drawer side panel M as shown with 3x screws
(#8). Ensure that the wheel of the runner is at the end with the 2x pilot holes.
STEP 15:
Create the drawer by attaching side panels (L & M) to the drawer back panel (O)
using 4x screws (#14).The runners are to be on the outside of the drawer frame with
the wheels of the runners at the back of the drawer.
Slide in the drawer base panel P. Finally, position the drawer front onto the front of the
drawer, insert 4x cam locks (#2) and turn clockwise to lock.
4x #14 25mmL Screws
Hardware for Step 15:
4x #2 Cam Locks
#1 #1
#1
#1
N
STEP 14:
Prepare drawer front panel (N) by inserting 4x cam dowels (#1)
1x #12 RH ‘L-Shaped’
Runner
Hardware for Step 13:
3x #8 12mmL Screws
#8
#8
#8
#12
M
N
P
M
L
#14
#14
#14
#14
O#22x
#22x

11
STEP 17:
Insert the hanging rail.
Thread the two collars (#15) onto the rail making sure the threaded ends are facing
away from each other and towards each end of the rail itself. Insert one end of the rail
into the mounting plate on the side panel and tighten, then position and tighten the
remaining end to the remaining mounting plate.
Ensure the collars are fully tightened.
STEP 16:
Slide the drawer into the wardrobe.
2x #15 Collar
Hardware for Step 17:
#15 Q
#15
#15
#15

12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
STEP 19:
Attach the 3x hinges (#17) to the back of the LH door R using 6x screws (#7).
Repeat for the RH door S.
S
#72x
#72x
#72x
6x #17 Hinges
Hardware for Step 19:
12x #7 12mmL Screws
2
2
2
2
R
#72x
#72x
#72x
#17
#17
#17
#17
#17
#17
TOP
BASE
STEP 18:
Fitting the hinges.
Attach the 3x hinge base plate (#16) to both of the side panels. There are 3 hinges for
each panel.
It is best to leave the screws slightly loose to allow for aligning the hinges when
attaching the door.
6x #16 Hinge Base Plates
Hardware for Step 18:
12x #7 12mmL Screws
#16
#16
#16
#16
#16
#16
#72x
#72x
#72x
#72x
#72x
#72x
#16
#7
#7
#16
#7
#7

13
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
2
STEP 21:
Attaching the doors.
Repeat step 20 for the LH door R.
Once all hinges are installed on both doors, you can check the alignment of the
door and adjust as required. Please see the adjustment guide at the end of these
instructions.
When happy, tighten ALL the hinge application screws.
R
#17
#17
#17
#16
#16
#16
STEP 20:
Attaching the doors.
Ensure that all the hinges are in the open position (as shown) on the RH Door S.
With the assistance of a second person to support the door, start at with the bottom
hinge and locate the 2 hooks on the hinge onto the front of the hinge raised section
of the hinge base plate (1). Once located in place, push down on the back of the hinge
until you hear a click to denote the hinge is latched in place (2).
Repeat process for each hinge working up the door.
S
#17
#17
#17
#16
#16
#16
NOTE: Steps 20 & 21 could be completed with the
wardrobe on it’s side with the door being xed laying
on the oor with packaging underneath it to raise it to
the required level. This should still be completed with 2
people as it involves moving the whole wardrobe.

14
STEP 22:
Your unit is now ready to use.
Before you use your unit, we strongly advise that you attach the anti-tip kit (included)
to the wardrobe to secure this product to the wall.
Please use the pilot holes on the back panel (highlighted in step 11) to attach the anti-
tip brackets using the hardware included with the kit.
Please refer to the instructions in the kit provided for further guidance.

15
Copyright© 2016 G.L.T.C. Ltd.All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.
2Lateral/Horizontal Adjustment: Moving the door side to side. (To control
the gaps between the door and the side panels)
#A2
#A3
Release screw A2 a little (this is a locking screw).
Then turn A3 screw to adjust the position of the door
(tighten or loosen)
Adjust one hinge at a time.
When correct position is achieved, re-tighten screw A2
on each hinge.
Repeat with the second door
3Forward/backward Adjustment: Moving the door in or out. (To make sure the
doors are flush with the front edge of the side panel)
#A2
Turn screw A2 a little to adjust the door.
Adjust one hinge at a time.
When correct position is achieved, repeat with the
second door.
1Vertical Adjustment: Moving the door up and down. (To control the gaps
between the door and the top/bottom panels)
#A1
#A1
Ensure one person is
holding the door. Unscrew/
loosen the screws shown
on each hinge of one door.
Do not remove the screws
completely.
Once the screws are
released, move the door to
the required position.
When in the corrected
position, re-tighten the
screws.
Repeat with the second
door.
#A1
#A1
Hinge Adjustment - For wardrobes with cup hinges
Note: 2 people should complete the adjustment. One holding the
door, one adjusting the screws