GTD GTD-371C II BSW User manual

GTD-371C II BSW
371W II Moving Head
User Manual

GTD all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without
notice. GTD logo and identifying product names and numbers herein are trademarks of GTD. Copyright protection claimed
includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or
hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged. All non-GTD brands and product names are trademarks or registered trademarks
of their respective companies.
GTD and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical
damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information
contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation,
rigging, and operation of this product.
Guangzhou GTD Culture & Technology Group Co.,Ltd. | 27 Fu Yuan Yi Road, Guangzhou 510805, P.R.China
[phone] | [phone] fax | www.gtd-lighting.com | [e-mail]

Table of contents
1. Safety instructions.......................................................................................................................................................1
2. Product introductions.................................................................................................................................................3
2.1 Dimensions..............................................................................................................................................................3
2.2 Fixture overview......................................................................................................................................................4
2.3 Accessories..............................................................................................................................................................4
3. Packing and shipping..................................................................................................................................................5
3.1 Protection lock.........................................................................................................................................................5
3.2 Unpacking...............................................................................................................................................................5
3.3 Packing after use .....................................................................................................................................................5
4. Installation...................................................................................................................................................................6
4.1 Clamps installation..................................................................................................................................................6
4.2 Device installation...................................................................................................................................................6
4.3 Lamp fitting and adjustment...................................................................................................................................7
5. Power / Control connection ......................................................................................................................................8
5.1 Power connection....................................................................................................................................................8
5.2 Control connection..................................................................................................................................................8
5.3 Testing.....................................................................................................................................................................8
6. Control panel...............................................................................................................................................................9
6.1 Panel instruction......................................................................................................................................................9
7. Technical specification..............................................................................................................................................10
8. Gobos and colors.......................................................................................................................................................13
8.1 Gobo specification ................................................................................................................................................13
8.2 Gobos ....................................................................................................................................................................13
8.3 Colors....................................................................................................................................................................14
9. Menu structure..........................................................................................................................................................15
10. DMX protocol..........................................................................................................................................................18
11. System wiring diagram...........................................................................................................................................22
12. Maintenance and Troubleshooting........................................................................................................................23
12.1 Cleaning and maintenance...................................................................................................................................23
12.2 Troubleshooting...................................................................................................................................................23
13. Spare parts list.........................................................................................................................................................27

GTD-371C II BSW
1
1.Safety instructions
Before using the fixture, read the latest version of the product user manual, paying particular attention to
the safety instructions. Please check www.gtd-lighting.com for the latest revision/update of the user manual.
m
ta
tc
The manufacture of this fixture, are not responsible for damages, resulting from misuse of this
fixture, due to the disregard of the information printed in this user manual.
DANGER!
Hazardous voltage. Risk of lethal or severe electric shock
WARNING!
Wear protective eyewear. Never look directly into the light source.
WARNING!
Burn hazard. Hot surface. Do not touch.
Only to direct mounting on non-combustible surfaces.
Minimum distance to lighted objects.
Replace all cracked glass shields.
Indoors use only！
Maximum ambient temperature.
Maximum temp of the external surface.

GTD-371C II BSW
2
General guidelines
Never open this fixture while in use.
The fixture should be kept clean. DO NOT operate the fixture in extreme heat or dusty environments.Avoid contact
with chemical liquid.
This fixture is a professional light effect designed for INDOOR / DRY LOCATIONS ONLY on stage, in nightclubs,
theatres, etc.
Minimum distance to lighted objects must be 49.21feet (15m).
Maximum temp of the external surface 248˚F (120˚C).
Maximum ambient temperature 113˚F (45˚C).
Minimum distance of inflammable materials from the surface 1.6 feet (0.5m).
Lamp should be changed if damaged or distorted in shape due to extreme heat.
Cover, prism or LCD Menu Function Display with visible damages such as cracks or scratches must be replaced to
ensure performance of the fixture.
Disconnect the fixture from power before changing any parts or accessories.
Basic insulation should be maintained between the controllable device and the product power supply.
Make sure that the installation area can hold a minimum point load of 10 times the weight of all installed
fixtures, clamps, cables, auxiliary equipment, etc. Check that the cover, clamps and locks are undamaged. Certified
safety cables must always be used when installing the fixture.
The fixture is only intended for installation, operation and maintenance by qualified professional. Instructions stated in
the manual must be complied.
The fixture must be kept in a well-ventilated place at least 50 cm away from any wall surface. Check if the fans or
ventilation openings are unblocked.
This fixture uses discharge lamp. To avoid reducing the lamp’s life, wait at least 15 minutes after powering off to allow
the unit to cool down before handling.
Broken or damaged cables and light source can only be fixed or changed by certified technicians, certified local
distributors or the manufacturer to ensure operational safety.
Do not stick filters or other materials onto the lens. Do not modify the fixture or install other than GTD manufactured
parts.
For questions regarding safety operation, please contact our technical personnel or call the service hotline
[phone].

GTD-371C II BSW
3
2. Production instructions
2.1 Diamension
568mm
[22.4in]
441mm
[17.3in]
140mm
[5.5in]
434mm
[17.1in]
489mm
[19.3in]
661mm
[26in]
450mm
[17.7in]
270°
270°
270°

GTD-371C II BSW
4
2.2 Fixture overview
2.3 Accessories
Item
Qty
Unit
Remark
User Manual
1
Pc
--
Clamps
2
Set
20-63mm
Safety cable
1
Pc
Φ5*60cm 7*19 pc with hook Material：Steel
3-pins signal line
1
Set
--
灯头组件
花样组件
底箱组件
折叠灯钩
光源组件
水平垂直扫描
Head module
Color & gobo & CMY
wheels module
Light module
Pan&tilt scan
Fold clamps
Base module

GTD-371C II BSW
5
3. Packing and shipping
3.1 Protection lock
Pan and tilt locks are equipped to ensure safe transportation.
PAN: 4 lock positions are located evenly on the Pan.
TILT: 5 lock positions are located on left and right side of the Tilt with the third one in the center.
3.2 Unpacking
Notes
All products arequalitycontrolled and checked for anyfaults before theyare dispatched to customers. If the fixture is damaged
during delivery, the customer must notify the shipper and manufacturer to file a damage insurance claim. Photographic
evidence of the damage must be provided.
Flight-Case：Open the cover of the flight-case and remove the plastic packing bags. Hold the handles of the fixture firmly
and take it out carefully.
Cardboard box：Open the box and take out the whole set of packaging foam which contains both the fixture and its
accessories. Remove the foam from the top, put away the accessories, and then take out the fixture wrapped in the plastic
bag.
Notes
Check if the pan and tilt are unlocked before connecting the fixture to power.
3.3 Packing after use
1. Switch off the fixture and wait for at least 5 minutes before disconnecting it from AC power. Cool down the fixture for
at least 15 minutes before packing.
2. Lock pan and tilt.
水平保护 锁
垂直保护锁

GTD-371C II BSW
6
3. Flight case: Wrap the fixture in plastic bags. Hold it by the handles, and then carefully place it inside the flight case along
with all the accessories. Close the cover. Only 3 layers are allowed when piling up the flight cases. Do not upside down.
4. Cardboard box: Wrap the fixture in plastic bags. Put it in the packaging foam along with all the accessories. Place the
other set of packaging foam on top then carefully put it inside the cardboard box.
4. Installation
4.1 Clamps installation
The fixturecan be placed on the stageor mounted on the truss facing anydirection. Attach the clampsto the mounting position
on the base of the fixture.
Warning：Use two clamps when mounting the fixture. Turn the screws attached to each clamp a 1/4 turn clockwise to lock.
Always remember to use the safety cable which goes through the mounting hole on the base. Do not attach the safety cable
on the handle.
4.2 Device installation
1. Make sure there is no damage on the clamps or safety cables before installation.
2. The clamp is mounted on the chassis of the fixture. Horizontally insert the clamp into the mounting holes of the chassis.
Fasten the clamp tightly by a 1/4 turn clockwise. Fix another clamp in the same way.
3. Check if pan and tilt are unlocked before connecting the unit to AC power.

GTD-371C II BSW
7
4.3 Lamp fitting and adjustment
1. Disconnect the fixture from AC power. Cool down the fixture. Set the Tilt lock in a horizontal position.
2. Use a flathead screwdriver to loosen the back cover. Remove the lamp by anticlockwise rotating and pull it out.
3. Push the light bulb to the hole on the reflector. Rotate 1/4 turn clockwise until it is securely fastened.
4. Observe the outlet of the reflector when pushing.
5. After fixing the lamp, install the back cover.
105mm
[4.1in] 105mm
[4.1in]
250mm
[9.8in]
105mm
[4.1in]
698mm
[27.5in]
?50 mm
[2in]
Safety cable
mounting position
Clamp Clamp

GTD-371C II BSW
8
Note
The fixture is equipped with Metal Halide 371W short arc discharge lamp, which is featured with high efficiency and short-
arc characteristic, such as a stable 7400K color-temperature and average lifespan of 1500h.
Note
1. Fitting another type of lamp will cause potential damage to the fixture. Change the lamp before it reaches its lifespan.
Read the guidelines in the package carefully when fixing the lamp.
2. To avoid any impact on the beam, do not touch the bulb with your bare hands. The lamp must be kept clean with the use
of the clean paper contained in its package
Enlarged
P ush the lightbulb t
o the hole，press it
dow n
Back cover
Back cover
Remove the back

GTD-371C II BSW
9
5. Power/ Control connection
5.1 Power connection
Connection method:
L (Live) Brown wire
E (Earth) Yellow / Green bi-color wire
N (Neutral) Blue wire
The voltage and frequency of the power source must be in compliance with the ones marked on the fixture. It is strongly
recommended that each fixture are to be connected to the power source separately so that they can be switched on / off
individually.
5.2 Control connection
The fixture has 3-pin XLR connectors for DMX data input and output as shown below. Connection between the console and
fixture, and between fixtures must be made with 2 core screened DMX signal cable. Maximum connecting distance of signal
cable is 150 meters. Additional DMX512 signal-amplifier is recommended for longer distance
Connect the Console’s DMX OUTPUT to the first fixture’s DMX INPUT, then the first fixture’s DMX OUTPUT to the
second fixture’s DMX INPUT and so on. It is recommended not to connect more than 32 units on a single DMX universe.
On the last fixture‘s output connect a DMX terminator. (The terminator is a 3-pin XLR connector with a 1/2W and 120Ω
resistor between the pin 2 and pin 3) as shown below:
5.3 Testing
Console Input Terminator
Output Input Output Input Output
12 312 3
DMX 512
1：Ground
2：—
3：+
15
324 15 324
DMX 512
1：Ground
2：—
4：Reserved
5：Reserved
3：+

GTD-371C II BSW
10
Connect the fixture to AC power. Check if the lamp is on and the fixture is independently controllable before
putting into operation.
6. Control panel
6.1 Panel instruction
The control panel features touch-sensitive buttons and LCD digital display for quick and easy setup of address code
and functions menu.
Press UP or DOWN to view or select the function menu.
Press ENTER to choose a function and enter into corresponding sub menu. Each menu represents a specific function
of the fixture.
Press ENTER to select the specific function and save the changes or enter into the submenu, then press UP or DOWN
to change the value of the selected function (increase or decrease).
Press MENU to return to the previous menu or exit.
LED indicators:
Power on: RED power LED indicator on
15
GTD-470 N BSW
GTD-371C II BSW

GTD-371C II BSW
11
7. Technical specification
Optical
Light source: Spec SIRIUS HRI 371W
Expected average lifetime: 1500 h
Color temperature correction: 7500K
Zoom: BEAM 0°~2.5°/ SPOT 3°～43°/WASH 4°～45°
CRI：Ra≥80
Focus: High-precision glass lenses, electronic linear HD focus
Prism: 1 pc tip 16-facet prism，1 pc Symmetry facet prism, prims can be controlled independently ,
or can be combined to make abundant beam effects
Frost: 1-independent frost effect
Gobo
Rotating gobo wheel: 8 interchangeable gobos + open, indexing, CW/CCW rotation, variable speed
Fixed gobo wheel: 6 gobos + open，CW/CCW rotation, variable speed
Gobo outside diameter: 14.4mm
Max. Image diameter: 6mm
Max. Thickness: 0.5mm
Gobo material: metal
Color
Color wheel: 2 Colors wheel，8 colors, split color and linear color shifing
CMY: CMY linear infinity color mixing，with built-in macros
CTO: CTO linear color temperature adjusting,7500K~2700K

GTD-371C II BSW
12
Electrical
Power input, nominal:AC 100-240V ~50/60Hz
Max. Power consumption: 503.1W, max current: 5.083A, PF: 0.996
Power supply unit: Auto-ranging electronic SMPS
Main fuse: 250V/15A
Ballast: Electronic
Power input: Self-contained power cord
DMX data input/output: Chassis 3-pin (in/out)
Control and programming
Control channels (DMX): 24/23/32
Protocol: DMX-512 RDM
Display: LCD
Physical / Installation
Weight: 27.9Kg (61.5lbs.)
IP rating: IP20
Material: Aluminum, steel, plastic
Mounting points: Four quarter-turn locking points + attachment points for safety wire
Dynamic effects
Pan/Tilt movement: 540˚/270˚
Iris: Motorized adjustable iris, wide range of variable pulse effects
Strobe: 1-25Hz, synchronized, pulse effects
Dimmer: 0-100%, mechanical dimming
Thermal
Operating range: 5˚F to 113˚F (-15˚C to +45˚C)
Startup range: -13˚F to 113˚F (-25˚C to +45˚C)
Storage range: -40˚F to 140˚F (-40˚C to +60˚C)
Cooling: Active fan
Humidity: ≤85%
Certification and Safety
EMC: EN 55103-1:2009, EN 55103-2:2009, EN 61000-3-2:2006+A2:2009, EN 61000-3-3:2013,
GB/T 17743-2007, GB 17625.1-2012
Safety: EN 60598-2-17:1989/A2:1991, GB 7000.1-2015, GB 7000.217-200811
Photometric

GTD-371C II BSW
13
0
5m
10m
15m
20m
25m
5m
10m
15m
20m
25m
Beam D iameter(m/ft.) ( 2.5 °)
Distance(m/ft.) 0 20/65.6
Ø0.87/2.85 Ø1.74/5.71 Ø2.61/8.57 Ø3.48/11.42
40/131.2 60/196.9 80/262.5
Il
BEAM
lu m in an ce(LUX)
86350 21588 9595 53972.5°
2°

GTD-371C II BSW
14
Other teatures
Enhanced stability of the fixture due to the wide input voltage AC/DC switching power supply which both reduces the
impact of power and voltage fluctuations, and removes the restriction of voltage and frequency variations in different
countries.
Automatic energy saving: when the shutter or CMY is closed, power consumption will be reduced automatically with
the photoelectric tracking induction technology.
Sleep mode: uses the most advanced technology to remotely activate sleep mode. When the fixture is disconnected from
signal, the sleep mode is enabled automatically to make it more stable and safer. Sleep time can be customized.
Power setting: built-in continuous rechargeable battery, allowing setting functionaldata via LCD interface without power
connection
0
5m
10m
15m
20m
25m
5m
10m
15m
20m
25m
Beam Diameter(m/ft.)( 3 °)
Beam Diameter(m/ft.)( 43°)
Distance(m/ft.) 0 5/16.4
Ø0.29/0.95 Ø0.52/1.71 Ø0.72/2.36 Ø0.88/2.89
Ø3.94/12.93 Ø7.66/25.13 Ø10.5/34.45 Ø13.9/45.60
10/32.81 15/49.21 20/65.62
Il
SPOT
lu m in an ce(LUX)
409000 151000 81920 529903°
3518 916 390 21943 °
3°43°
0
5m
10m
15m
20m
25m
5m
10m
15m
20m
25m
B50%
10%
50%
10%
eam D iameter(m/ft.)( 4 °)
Beam Diameter(m/ft.)( 4 °)
Distance(m/ft.) 0 5/16.4
Ø0.16/0.52 Ø0.34/1.11 Ø0.38/1.25 Ø0.50/1.64
Ø0.33/1.08 Ø0.78/2.56 Ø0.80/2.62 Ø0.98/3.22
Beam Diameter(m/ft.)( 45°)
Beam Diameter(m/ft.)( 45 °)
Ø2.11/6.92 Ø3.82/12.53 Ø6.31/20.70 Ø8.04/26.38
Ø4.14/13.58 Ø9.26/30.38 Ø13.1/42.98 Ø16.4/53.81
10/32.81 15/49.21 20/65.62
Il
WASH
lu m in an ce(LUX)
290000 95800 57220 353304°
2687 670 310 21045 °
4°45°

GTD-371C II BSW
15
8. Gobos and colors
8.1 Gobo specification
All patterns are made onto the metal gobos, and can be customized according to user’s requirement.
The customized size is as below:
Gobo material
Outer dimension
Effective dimension
Thickness
metal gobo
Φ14.4mm
Φ6mm
0.5mm
Gobo material: metal
8.2 Gobos
One rotating gobo wheel: 8 interchangeable gobos + open, indexing, CW/CCW rotation, variable speed
One fixed gobo wheel: 6 gobos + open, CW/CCW rotation, variable speed

GTD-371C II BSW
16
8.3 Colors
Two color wheel: 8 colors, split color, CW/CCW rotation,“Rainbow effect”in both directions

GTD-371C II BSW
17
9. Menu structure
Level 1
Level 2
Level 3
Level 4
Info
Run setting
Address Setting
Value Display
Auto-Program
IP Setting
Mask Address
SysID Setting
Address: 001~ XXX
Pan ……，All，No
Master/Alone
192.168.xxx.xxx
255.255.255.xxx
xxx
Setting the DMX address
Display the channel value
Run auto program in master or slave
Setting ARTNET network address
Setting ARTNET subnet address
Setting Device ID
Device Info
Time Info
This Time
Total Time
Last Time
Lamp On Time
Lamp Off Time
Last Time Code
Clear Last Time
Lamp Time Code
Clear Lamp Time
XXXXXX Hour
XXXXXX Hour
XXXXXX Hour
XXXXXX Hour
XXXXXX Minute
Password: xxx(88)
Yes/No
Password: xxx(111)
Yes/No
Since power on time
Product total run time
Last product run time
Lamp on time
Lamp close time
Clear last time password
Clear last time
Clear lamp time password
Clear lamp time
Temperature
Body Temperature
XXX ’C/’F
Body temperature
Fans Info
NO/...
Err Info
No Err/...
Software Version
XX RDM Code0951-
xxxxxx
The software version and RDM code