GTD GTD-F3 II BSW User manual

GTD-F3 II BSW
Moving Head
User Manual

2
GTD all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without
notice. GTD logo and identifying product names and numbers herein are trademarks of GTD. Copyright protection claimed
includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or
hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged. All non-GTD brands and product names are trademarks or registered trademarks
of their respective companies.
GTD and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical
damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information
contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation,
rigging, and operation of this product.
Guangzhou GTD Culture & Technology Group Co.,Ltd. | 27 Fu Yuan Yi Road, Guangzhou 510805, P.R.China
[phone] | [phone] fax | www.gtd-lighting.com | [e-mail]
P/N：1502011108A

2
Contents
1. Safety instructions.......................................................................................................................................................1
2. Product introductions.................................................................................................................................................3
2.1 Dimensions..............................................................................................................................................................3
2.2 Fixture overview......................................................................................................................................................4
2.3 Accessories..............................................................................................................................................................4
3. Packing and shipping..................................................................................................................................................5
3.1 Protection lock.........................................................................................................................................................5
3.2 Unpacking...............................................................................................................................................................5
3.3 Packing after use .....................................................................................................................................................6
4. Installation...................................................................................................................................................................7
4.1 Clamps installation..................................................................................................................................................7
4.2 Device installation...................................................................................................................................................7
5. Power / Control connection ......................................................................................................................................8
5.1 Power connection....................................................................................................................................................8
5.2 Control connection..................................................................................................................................................8
5.3 Testing.....................................................................................................................................................................8
6. Control panel...............................................................................................................................................................9
6.1 Panel instruction......................................................................................................................................................9
7. Technical specification..............................................................................................................................................10
8. Gobos and colors.......................................................................................................................................................12
8.1 Gobos ....................................................................................................................................................................12
8.2 Colors....................................................................................................................................................................12
9. Menu structure..........................................................................................................................................................14
10. DMX protocol..........................................................................................................................................................17
11. System wiring diagram...........................................................................................................................................28
12. Maintenance and Troubleshooting........................................................................................................................29
12.1 Cleaning and maintenance...................................................................................................................................29
12.2 Troubleshooting...................................................................................................................................................29
13. Spare parts list.........................................................................................................................................................32

1
1.Safety instructions
Before using the fixture, read the latest version of the product user manual, paying particular attention to
the safety instructions. Please check www.gtd-lighting.com for the latest revision/update of the user manual.
m
ta
tc
The manufacture of this fixture, are not responsible for damages, resulting from misuse of this
fixture, due to the disregard of the information printed in this user manual.
DANGER!
Hazardous voltage. Risk of lethal or severe electric shock
WARNING!
Wear protective eyewear. Never look directly into the light source.
WARNING!
Burn hazard. Hot surface. Do not touch.
Only to direct mounting on non-combustible surfaces.
Minimum distance to lighted objects.
Replace all cracked glass shields.
Maximum ambient temperature.
Maximum temp of the external surface.

2
General guidelines
The protection rating of this product IP66.
Never open this fixture while it is in use.
The fixture should be kept clean. DO NOT operate the fixture in extreme heat or dusty environments. Avoid contact
with chemical liquid.
Minimum distance of inflammable materials from the surface 1.6 feet (0.5m).
Maximum ambient temperature 113˚F (45˚C).
Maximum temp of the external surface 176˚F (80˚C).
Minimum distance to lighted objects must be 15m (49.21 feet).
Lamp should be replaced if damaged or distorted in shape due to extreme heat.
Cover, prism or LCD Menu Function Display with visible damages such as cracks or scratches must be replaced to
ensure performance of the fixture.
Disconnect the fixture from power before changing any parts or accessories.
Basic insulation should be maintained between the controllable device and the product power supply.
Make sure that the installation area can hold a minimum point load of 10 times the weight of all installed fixtures,
clamps, cables, auxiliary equipment, etc. Make sure that the cover, clamps and locks are undamaged. Certified safety
cables must always be used when installing the fixture.
The fixture is only intended for installation, operation and maintenance by qualified professional. Instructions stated in
the manual must be complied.
The fixture must be kept in a well-ventilated place at least 50 cm away from any wall surface. Check if the fans or
ventilation openings are unblocked.
This fixture uses discharge lamp. Avoiding reduce the lamp’s life, wait at least 15 minutes after powering off to allow
the unit to cool down before handling.
To ensure operational safety, broken or damaged cables and light source can only be fixed or replaced by certified
technicians, certified local distributors or the manufacturer.
Do not stick filters or other materials onto the lens. Do not modify the fixture or install other than GTD manufactured
parts.
For questions regarding safety operation, please contact our technical personnel or call the service hotline
[phone].

3
2. Production instructions
2.1 Dimension

4
2.2 Fixture overview
2.3 Accessories
Item Qty Unit Remark
User Manual 1 Pc --
Clamps 2 Set Hanging integrated folding lamp.
Safety cable 1 Pc Φ4*60cm 7*19 pc with hook Material：Steel
3-pins signal line 1 Set 1.5m*2.5mm² connect blue plug

5
3. Packing and shipping
3.1 Protection lock
Pan and tilt locks are equipped to ensure safe transportation.
The horizontal axis has 4 locking points and the vertical axis has 5 locking points.
3.2 Unpacking
Notes
All products are quality controlled before they dispatched to customers. If the fixture is damaged during delivery,
the customer must notify the shipper and manufacturer to file a damage insurance claim. Photographic evidence
of the damage must be provided.
Flight-Case(specification:
575*525*690mm mm)：
Uncover the flight-case and remove the plastic packing bags.
Hold the handles of the fixture firmly and take it out carefully.
Cardboard box(specification：790*550*975mm)
：Open the box and take out the whole set of packaging foam
which are contained both the fixture and its accessories. Remove the foam from the top, put away the
accessories, and then take out the fixture wrapped in the plastic bag.
Notes
Check if the pan and tilt are locked before connecting the fixture to power
3.3 Packing after use
1. Switch off the fixture and wait for at least 5 minutes before disconnecting it from AC power. Cool down the
fixture for at least 15 minutes before packing.
2. Lock pan and tilt.
3. Flight case: Wrap the fixture in plastic bags. Gripping the handle and then place it in the flight case along with
all the accessories carefully. Close the cover lid. The wrap page are not allowed over 3 layers. Do not upside
down.
4. Cardboard box: Wrap the fixture in plastic bags. Put it in the packaging foam along with all the accessories.
Place the other set of packaging foam on top then put it carefully in the cardboard box.

6
4. Installation
4.1 Clamps installation
The fixture can be placed on the stage or mounted on the truss which faces any direction. Attach the clamps to
the mounting position on the base of the fixture.
Warning：
Use two clamps when mounting the fixture. Turn the screws attached to each clamp a 1/4 turn clockwise
to lock. Always remember to use the safety cable which goes through the mounting hole on the base. Do not attach
the safety cable on the handle.
4.2 Device installation
1. Make sure there is no damage on the clamps or safety cables before installation.
2. The clamp is mounted on the chassis of the fixture. Horizontally insert the clamp into the mounting holes of the
chassis. Fasten the clamp tightly by a 1/4 turn clockwise. Fix another clamp in the same way.
3. Check if pan is locked before connecting the unit to AC power.

7
4.3 Lamps installation
1. Disconnect the power, cool down the fixture, and set the Tilt lock-catch on the arm in a horizontal
position.
2. Use a screwdriver to rotate 1/4 circle counter-clockwise to unscrew the four quick bolts on the lamp’s
back-cover.
3. Pull the back cover out gently in parallel direction by hands, and pull it in full place to let it drop down
naturally.
4. Let the dot on the sphere of the lamp face to the back and the sphere face to the front, put the lamp
horizontally into the slot on the lamp-holder and make sure that the lamp’s metal handle already be in alignment
with the bayonet edge of the holder. Then press the metal legs at the ends of the lamp gently down to the right
position, and make sure the lamp has been fixed well to the position.
5. And then push the back-holder with the fixed lamp gently into the reflector, observing the lamp after
finising, and plug in the windproof fan.
lamp cover
Dismantle cover
Dismantle lamp cover
Fit the light bulb

8
Attention
The fixture is equipped with PHILIPS MSD Platinum Flex 300S which is featured with high efficiency and
short-arc characteristic, such as a stable 7200K color-temperature and average lifespan of 6000h.
Attention
1. There is potential damage to the fixture if fitting another type of lamp. Change the lamp before it reaches
its lifespan. Read the guidelines in the package carefully when fixing the lamp.
2. To avoid any impact on the beam, do not touch the bulb with your bare hands. The lamp must be kept
clean with the use of the clean paper contained in its package.

9
5. Power/ Control connection
5.1 Power connection
Connection method:
L (Live) Brown wire
E (Earth) Yellow / Green bi-color wire
N (Neutral) Blue wire
The numbers of series circuit：6 （220VAC/50HZ）
The voltage and frequency of the power source must be in compliance with the ones marked on the fixture.
It is strongly recommended that each fixture are to be connected to the power source separately so that they
can be switched on / off individually.
5.2 Control connection
The fixture has 3-pin XLR connectors for DMX data input and output as shown below. Connection between the
console and fixture, and between fixtures must be made with 2 core screened DMX signal cable. Maximum
connecting distance of signal cable is 150 meters. Additional DMX512 signal-amplifier is recommended for
longer distance.
Connect the Console’s DMX OUTPUT to the first fixture’s DMX INPUT, then the first fixture’s DMX OUTPUT to
the second fixture’s DMX INPUT and so on. It is recommended not to connect more than 32 units on a single
DMX universe. On the last fixture’s output connect a DMX terminator. (The terminator is a 3-pin XLR connector
with a 1/2W and 120Ω resistor between the pin 2 and pin 3) as shown below:
5.3 Testing
Connect the fixture to AC power. Check if the lamp is on and the fixture is independently controllable before
putting into operation.
Input Output
Input Output
DMX terminator
Output Input
Console

10
6. Control panel
6.1 Panel instruction
The control panel features touch-sensitive buttons and LCD digital display for quick and easy setup of
address code and functions menu.
Press UP or DOWN to view or select the function menu.
Press CNTERtochoose afunctionandenterintocorrespondingsubmenu.Eachmenurepresentsa specific
function of the fixture.
Press RIGHT to select the specific function and save the changes or enter into the submenu, then press
UP or DOWN to change the value of the selected function (increase or decrease).
Press RIGHT to return to the previous menu or exit.

11
7. Technical specification
Optical
Light source: PHILIPS MSD Platinum Flex 300S
Expected average lifetime: 6000 h
Color temperature correction: 7200K
Lumens:16000lm
Zoom range：BEAM 0°～2.5°/ SPOT 3°～ 43°/ WASH 4°～ 45°
CRI：Ra≥80
Focus: with precision HD Glass lens, electronic linear focus clearly
Prism: 1 sixteen-prism,double opposite mirror
Frost: 1-independent frost effect
Gobo
Rotating gobo wheel: 1 interchangeable gobo rotator, 8 optional pattern pieces,
Fixed gobo wheel:6 gobos + open, CW/CCW rotation, variable speed.
Gobo outside diameter: 14.4mm
Max. Image diameter: 6mm
Max Thickness:0.5mm
Gobo material: metal
Color
Color wheel: 11 color gel and open gobo, linear adjustment function, “Rainbow effect” in both directions
Electrical
Power input, nominal: AC 200-240V 50/60Hz
Max. Power consumption: 570W
Max current: 2.5A, PF: ≧0.99
Power supply unit: ≧0.99
Main fuse: 6.3A
Power input: Self-contained power cord
DMX data input/output: Chassis 3-pin
Control and programming
Control channels (DMX): 19/16/22
Protocol: DMX-512 RDM
Display: LCD
Physical / Installation
Weight: 28kg (61.73lbs.)
IP rating: IP66
Material: Aluminum, copper, steel, plastic,iron
Mounting points: 4 fixed folding lamp hook + attachment points for safety wire

12
Dynamic effects
Pan/Tilt movement: 540˚/270˚，adopting a function which resets 32bit accurately and automatically
Strobe: 1-25Hz, strobe randomly, pulse randomly, strobe synchronously and asynchronously
Dimmer: 0-100%, mechanical linear dimming
Thermal
Operating range: 5˚F to 113˚F ( -15˚C to 45˚C)
Startup range: -13˚F to 113˚F( -25˚C to 45˚C)
Storage range: -40˚F to140˚F( -40˚C to60˚C)
Cooling: Active fan
Humidity: ≤85%
Certification and Safety
EMC: EN 55103-1:2009, EN 55103-2:2009, EN 61000-3-2:2006+A2:2009, EN 61000-3-3:2013,
GB/T 17743-2007, GB 17625.1-2012
Safety: EN 60598-2-17:1989/A2:1991, GB 7000.1-2015, GB 7000.217-2008
Photometric
0
2m
4m
6m
8m
10m
2m
4m
6m
8m
10m
Beam Diameter(m/ft.)
Distance(m/ft.) 020/65.6
Ø0.87/2.85 Ø1.7/1.44 Ø0.66/2.16 Ø0.87/2.85
40/131.2 60/196.9 20/262.5
Illu m inan ce(LUX)
759000 18975 8433 4743
2.5°
2.5°
(2.5°)
0
2m
4m
6m
8m
10m
2m
4m
6m
8m
10m
Beam Diameter(m/ft.)
Beam D iameter(m/ft.)
Distance(m/ft.) 05/16.4
Ø0.22/0.72 Ø0.44/1.44 Ø0.66/2.16 Ø0.87/2.85
Ø3.94/12.93 Ø7.66/25.13 Ø13.9/45.60 Ø10.5/34.45
10/32.81 15/49.21 20/65.62
Ill um inance(LUX)
796000 210000 130000 75900
2.5°
5440 920 389 336
43°
2.5° 43°
(2.5°)
(43°)

13
Other features
Enhanced stability of the fixture due to the wide input voltage AC/DC switching power supply which both
reduces the impact of power and voltage fluctuations, and removes the restriction of voltage and frequency
variations in different countries.
Automatic energy saving: when the shutter or CMY is closed, power consumption will be reduced automatically
with the photoelectric tracking induction technology.
Sleep mode: uses the most advanced technology to activate sleep mode remotely. When the fixture is
disconnected from signal, the sleep mode is enabled automatically to make it more stable and safer. Sleep
time can be customized.
Communications Design：DMX wired/wireless transmission, bidirectional-control technology,upgrade the
software quickly and conveniently by using DMX cable.
Thermal design: The wind drainage and intelligent temperature monitoring technology can monitor lighting’s
state : on /off. It can adjust the thermal design by the position’s temperature of lighting so that the temperature
can be controlled.
0
2m
4m
6m
8m
10m
2m
4m
6m
8m
10m
B50%
10%
eam Diameter(m/ft.)
Beam Diameter(m/ft.)
Distance(m/ft.) 05/16.4
Ø0.16/0.52 Ø0.34/1.11 Ø0.38/1.25 Ø0.50/1.64
Ø0.33/1.08 Ø0.78/2.56 Ø0.98/3.22 Ø0.80/2.62
10/32.81 15/49.21 20/65.62
Ill u m inan ce(LUX)
536000 137000 789000 45800
4°
4240 850 525 336 45°
4° 45°
(4°)
(4°)
B50%
10%
eam Diameter(m/ft.)
Beam Diameter(m/ft.)
Ø2.11/6.92 Ø3.82/12.53 Ø6.31/20.70 Ø8.04/26.38
Ø4.14/13.58 Ø9.26/30.80 Ø16.4/53.81
(45°)
(45°) Ø13.1/42.98

14
8. Gobos and colors
8.1 Gobo specification
All patterns are made onto the metal gobos, and can be customized according to user’s requirement.
The customized size is as below:
Gobo material Outer dimension Effective dimension Thickness
Glass gobo Φ14.4mm Φ6mm 0.5mm
Gobo material: Glass
8.2 Gobos
One rotating gobo wheel: 7 interchangeable gobos + open, indexing, CW/CCW rotation, variable speed
One fixed gobo wheel: 7 gobos + open, CW/CCW rotation, variable speed.
8.3 Colors
Color wheel: 9 colors + open, linear color conversion and “Half rainbow effect” in both direction.
1.RED 2.ORANGE 3.BLUE 4.GREEN
5.Magenta 6.YELLOW 7. CYAN 8.PINK
9.CTO 10.UV 11.CRI FILTER

15
9. Menu structure
Level 1 Level 2 Level 3 Level 4 Info
Run setting Address Setting
Value Display
Auto-Program
Address: 001~ XXX
Pan ……，All，No
Master/Alone
Setting the DMX address
Display the channel value
Run auto program in master
or slave
Device Info
Time Info This Time
Total Time
Last Time
Lamp On Time
Lamp Off Time
Last Time Code
Clear Last Time
Lamp Time Code
Clear Lamp Time
XXXXXX Hour
XXXXXX Hour
XXXXXX Hour
XXXXXX Hour
XXXXXX Minute
Password: xxx(88)
Yes/No
Password: xxx(111)
Yes/No
Since power on time
Product total run time
Last product run time
Lamp on time
Lamp close time
Clear last time password
Clear last time
Clear lamp time password
Clear lamp time
Temperature
Body Temperature
XXX ’C/’F
Body temperature
Fans Info
NO/...
Err Info
No Err/...
Software Version XX RDM Code0032-
xxxxxx
The software version and
RDM code
Lamp
Control Lamp On/Off
Power On Lamp
On
Console Lamp On
Console Lamp Off
Lamp On Temp.
Lamp Off Temp.
On/Off
Enable/Disable
Enable/Disable
Enable/Disable
20~79, 45’C
/68~174 ,
113’F
80~139,
130’C/176~282,266’F
Open lamp
Power on open lamp
Console open lamp
Console close lamp
Open lamp below
temperature
Close lamp above
temperature
System
Setting Status Setting Console Set Addr No Signal Status
Pan Reverse
Tilt Reverse
Pan Scan Degree
Scan Feedback
Standby Time
Enable/Disable
Off/Hold/Auto/Music
Enable/Disable
Enable/Disable
360/540
Enable/Disable
Disable/1~20 Min, 30
Address can be changed by
console
The status while no signal
Pan Reverse
Tilt Reverse
Pan Scan Degree
Scan Feedback
Standby time
Fan Speed Smart Control
High Speed
Low Speed
Auto fans speed
Fans high speed
Fans low speed
Display Setting Backlight Time
Keyboard Lock
Brightness Set
Language
Auto Screen Set
1~80 Min/Disable
Enable/Disable
15%~100% 80%
Chinese/English
on/off/Auto
Backlight off time
Press <menu> 3s to unlock
Brightness Set
Change the language
Screen display upside down
Temperature Unit Celsius Temperature unit

16
Fahrenheit
Value Default Pan…… Pan =XXX The default value
Wireless Dev
Wireless Off
Wireless On
Wireless Trans.
Wireless Reset
Wireless off
Wireless on
Wireless transfer DMX data
to another Wireless reset
Dimmer Mode
M0:...~M5:... M1
Dimmer mode select
Restore Default
Restore/Cancel
Restore to default value
Motor
Reset System Reset
Scan Reset
Color Reset
Gobo Reset
Strobe Reset
Other Reset
System reset
Pan and tilt motor reset
color motor reset
gobo motor reset
strobe motor reset
other motor reset
Channel
Adjust Test Mode Pan…… Every channel test
Manual Mode Pan:Pan =XXX:Manual control
Adjust Mode Input Password
Pan:
Password=XXX(99)
Pan=XXX:
The password ofadjust mode
Fixed all begin position
Channel
Setting
Channel Mode Standard Mode
Simplified Mode
Extended Mode
Custom Mode A
Custom Mode B
Custom Mode C
Standard channel mode
Simplified channel mode
Extended channel mode
Custom channel mode A
Custom channel mode B
Custom channel mode C
Set CustomMode1
Set Custom Mode2
Set Custom Mode3
Max Channel
Pan:Channel = XX Pan = CH01:Change the channel order
Program
Edit Select Group Program Unit 1 Program Unit 2
Program Unit 3
Auto-Program 1 ~10
Auto-Program 1 ~10
Auto-Program 1 ~10
Choose build-in program for
slave 1
Choose build-in program for
slave 2
Choose build-in program for
slave 3
Program Edit Auto-Program1:
Auto-Program10 Program Test
Step 1=Scene xxx
Step 64=Scene xxx
Test the auto program
The start scene of the
program
The end scene of the
program
Scene Edit Scene Edit:001-250 Pan,……（Pan=xxx）
Scene T:（=xxxS）
Rec. Outside
Edit the channel DMX
Edit the scene time
Get scene DMX form
console
Record Scene Scene XX->XX Record scene form console
*Settings hightlighted in light grey are default values

17
10. DMX Protocol
Standard
DMX mode
Name DMX value DMX percentage Function Default DMX
Value
Standard
(19ch)
1 Strobe/
Shutter
0 31 0.0% 12.2% Closed
0(0%)
32 63 12.5% 24.7% Open
64 127 25.1% 49.8% Synchronous strobe from slow to fast
128 159 50.2% 62.4% Open
160 223 62.7% 87.5% Random strobe from slow to fast
224 255 87.8% 100.0% Open
2 Intensit
y
0 255 0.0% 100.0% No light →Full light 0(0%)
3 0 65535 0.0% 100.0% Intensity fade, fine (LSB)
4 Color
wheel
0 17 0.0% 6.7% Open
0(0%)
18 27 7.1% 10.6% Color 1
28 37 11.0% 14.5% Color 2
38 47 14.9% 18.4% Color 3
48 57 18.8% 22.4% Color 4
58 67 22.7% 26.3% Color 5
68 77 26.7% 30.2% Color 6
78 87 30.6% 34.1% Color 7
88 97 34.5% 38.0% Color 8
98 107 38.4% 42.0% Color 9
108 117 42.4% 45.9% Color 10
118 127 46.3% 49.8% Color 11
128 187 50.2% 73.3% Color1 continous rotation CW from
slow to fast
188 195 73.7% 76.5% Stop
196 255 76.9% 100.0% Color1 continous contrarotation CCW
from slow to fast
5
Gobo
wheel
(static)
0 17 0.0% 6.7% Open gobo
0(0%)
18 22 7.1% 8.6% Gobo 1
23 27 9.0% 10.6% Gobo 2
28 32 11.0% 12.5% Gobo 3
33 37 12.9% 14.5% Gobo 4
38 42 14.9% 16.5% Gobo 5
43 47 16.9% 18.4% Gobo 6
48 52 18.8% 20.4% Gobo 7
53 57 20.8% 22.4% Open gobo
58 66 22.7% 25.9% Gobo 1 shake